Instrukcja obsługi Honeywell ST9400S
Honeywell
kontroler temperatury
ST9400S
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Honeywell ST9400S (2 stron) w kategorii kontroler temperatury. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/2
Copyright©Honeywell
50029833-004 A
HOT WATER HEATING
GUIDE TO THE USE OF THE ST9400S PROGRAMMER:
The purpose of the Programmer is to control the times when the heating and hot water can be switched on.
MODE buttons Slider
Normal Use:
Lift the flap to make sure the Slider is in the position.RUN
Also make sure that both hot water and heating are operating in AUTO or
ONCE mode, by pressing the buttons repeatedly until the display MODE
shows or .AUTO ONCE
AUTO means on and off twice each day, following the programme.
ONCE means coming on at the first programme time then off at the last
programme time.
To turn the hot water and heating OFF:
(1) Keep pressing the hot water MODE button until the display shows that
hot water is . If the hot water was on, the light will turn off. OFF
(2) Keep pressing the heating button until the display shows that MODE
heating is . If the heating was on, the light will turn off.OFF
To turn the hot water and heating ON:
(1) Keep pressing the hot water button until the display shows MODE
CONT (this is short for continuous). The hot water light will turn on.
The hot water will not turn off in this position.
(2) Keep pressing the heating button until the display shows MODE
CONT (this is short for continuous). The heating light will turn on.
The heating will not turn off in this position.
Temporary Overrides to the Set Programme:
To turn the hot water ON press the hot water OVERRIDE button – the light
will turn ON, unless the hot water is operating in the OFF mode.
To turn the hot water OFF press the hot water button again OVERRIDE
– the light will turn OFF.
This button will only work in the or modes. It will NOT work AUTO ONCE
in the or modes.OFF CONT
At the next SET time the Programmer will go back to automatic
operation.
(The same applies to the heating button)OVERRIDE
For a temporary boost of heating or hot water, press the corresponding
EXTRA HOUR button.
Pressing once brings the heating or hot water ON for 1 hour.
Press twice for 2 hours extra, three times for 3 hours extra.
Pressing again will turn the heating OFF.
This button works in the AUTO, ONCE, and OFF modes. It will NOT work
in the mode.CONT
If the heating or hot water is already ON, pressing the corresponding
EXTRA HOUR button will add the extra hours to the end of the current
ON period.
For guidance on the operation of the other buttons please refer to the complete user instructions supplied with the
product.
Hot Water
OVERRIDE button
HOT WATER HEATING
EXTRA HOUR
OVERRIDE
EXTRA HOUR
OVERRIDE
OK
NEXT
DAY/TIME
HOT WAT ER
HEATING
RUN
ST 940 0S
(1) (2)
HOT WATER HEATING
EXTRA HOUR
OVERRIDE
EXTRA HOUR
OVERRIDE
Heating
OVERRIDE button
Hot Water
EXTRA HOUR button
HOT WATER HEATING
EXTRA HOUR
OVERRIDE
EXTRA HOUR
OVERRIDE
Heating
EXTRA HOUR button
BOILER SERVICE REMINDER:
By Law, your gas boiler should be inspected once a year to ensure it is operating safely. Your ST9400S Programmer
has a range of features designed to help make sure this service is carried out at the correct time.
These features will be programmed by your Installer, Maintenance Engineer or Landlord.
• A message can be displayed on the screen to remind you that a boiler service is due
• If the service is overdue, the Programmer may switch off the heating system, to ensure your safety.
Countdown to service:
Your Programmer can indicate a countdown for the number of days until
a service is due. This type of message will appear on the screen every
few seconds, to give you an opportunity to arrange a service visit.
What you should do:
• Arrange for a service visit before the service is due.
When service is due:
When your gas boiler service is the words “ ” OVERDUE SERVICE DUE
will continue to flash on your screen.
What you should do:
• Arrange an immediate service visit.
Boiler shut-down:
If your Programmer shows the words “ ” and “ ” then SERVICE DUE OFF
your boiler service is and the boiler has been automatically OVERDUE
switched off to ensure your safety.
What you should do:
• Arrange an immediate service visit.
• If set to do so, it may be possible to obtain limited use of the boiler
by pressing any button. Each button press will allow EXTRA HOUR
operation of the boiler for 1 hour at a time, and the screen will show
the message “ ”On 1h
How to arrange a service visit:
• Your Landlord, Installer, or Maintenance Engineer should contact you
before the boiler service is due to allow you to arrange the service
visit. Their communication will include contact details.
• Contact details may also be found in the ST9400S User Guide, or may
be on an information sticker placed on or near the boiler.
• A contact telephone number may also have been programmed into
the Programmer. If so, a message will appear on the screen indicating
the number you should call.
Specyfikacje produktu
| Marka: | Honeywell |
| Kategoria: | kontroler temperatury |
| Model: | ST9400S |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Honeywell ST9400S, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje kontroler temperatury Honeywell
15 Czerwca 2024
15 Czerwca 2024
15 Czerwca 2024
15 Czerwca 2024
15 Czerwca 2024
15 Czerwca 2024
15 Czerwca 2024
15 Czerwca 2024
15 Czerwca 2024
15 Czerwca 2024
Instrukcje kontroler temperatury
- kontroler temperatury AEG
- kontroler temperatury Voltcraft
- kontroler temperatury Panasonic
- kontroler temperatury Carel
- kontroler temperatury IFM
- kontroler temperatury Techno Line
- kontroler temperatury Fluke
- kontroler temperatury Dimplex
- kontroler temperatury Hager
- kontroler temperatury ACV
- kontroler temperatury Inkbird
- kontroler temperatury Emko
- kontroler temperatury Kathrein
- kontroler temperatury JUNG
- kontroler temperatury Wachendorff
- kontroler temperatury AstralPool
- kontroler temperatury Cocraft
- kontroler temperatury SRS
- kontroler temperatury Ventus
- kontroler temperatury Technoline
- kontroler temperatury Davis
- kontroler temperatury Bulex
- kontroler temperatury Berker
- kontroler temperatury Opticlimate
- kontroler temperatury Ziehl
- kontroler temperatury Ygnis
- kontroler temperatury Jumo
Najnowsze instrukcje dla kontroler temperatury
27 Grudnia 2024
27 Grudnia 2024
27 Grudnia 2024
27 Grudnia 2024
27 Grudnia 2024
27 Grudnia 2024
27 Grudnia 2024
27 Grudnia 2024
27 Grudnia 2024
16 Grudnia 2024