Instrukcja obsługi Honeywell CT87K1012/E1

Honeywell termostat CT87K1012/E1

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Honeywell CT87K1012/E1 (16 stron) w kategorii termostat. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/16
Owners Manual
English: Page 1
Mode d’emploi
Français: Page 6
Manual de Uso
Español: Página 11
T87N Easy-To-SeeTM
The Round®
C
O
O
L
O
F
F
H
E
A
T
F
A
N
O
N
A
U
T
O
6
7
8
The Round® Easy-To-SeeT M
69-1840EFS-07
Check package contents:
Thermostat
Wall anchors & screws (2 each)
Owner's Manual
Large Print Subbase Switch Labels
Coverplate
Before you begin, make sure
you have:
No. 2 Phillips & small pocket
screwdrivers
Hammer
Level (optional)
Pencil
Drill and bit (3/16” for drywall, 7/32”
for plaster)
MERCURY NOTICE
If this product is replacing a control that contains mercury in a sealed tube, do not
place the old control in the trash. Contact your local waste management authority for
instructions regarding recycling and proper disposal.
CAUTION: ELECTRICAL HAZARD
Can cause electrical shock or equipment damage. Disconnect power before
beginning installation.
Must be installed by a trained, experienced technician
Read these instructions carefully. Failure to follow these instructions
can damage the product or cause a hazardous condition.
Pre-installation checklist
This thermostat contains a Lithium battery which may contain Perchlorate material.
Perchlorate Material—special handling may apply,
See www.dtsc.ca.gov/hazardouswaste/perchlorate
Read before installing
T87N, T87N1026
T87N Easy-To-SeeTM • Owner's Manual
69-1840EFS—07 2
System Types
Gas, oil, or electric heat with air
conditioning
Warm air, hot water, high-efficiency
furnaces, heat pumps, steam, gravity
Heat only
Heat only with fan
Cool only
System Settings
Heat, Off, Cool
Fan Settings
Auto, On
Specifications
Temperature Range
40° to 90°F (4.5° to 32°C)
Shipping Temperature
20° to 120°F (28.9° to 48.9°C)
Operating Relative Humidity
5% to 90% (non-condensing)
Electrical Ratings
Voltage: 2030 VAC
Running current:0.021.0 A,
50/60 Hz
Install the thermostat about 5 feet (1.5 m) above the floor in an
area with good air circulation at average temperature.
Do not install in locations where the thermostat can be affected by:
Drafts or dead spots behind doors and in corners
Hot or cold air from ducts
Sunlight or radiant heat from appliances
Concealed pipes or chimneys
Unheated/uncooled areas such as an outside wall behind the
thermostat
NO
NO NO
Installation tips
Product application
This thermostat provides electronic control of 24 VAC single-stage heating
and cooling systems.
English: Français: Español:Page 1 • Page 6 • Página 11
3 69-1840EFS—07
1. Pull wires through wire
hole. Position coverplate
on wall, level and mark hole
positions.
2. Drill holes (3/16” for
drywall, 7/32” for plaster)
and tap in supplied wall
anchors.
3. Pull wire through
coverplate and subbase,
position over anchors,
then insert and tighten
mounting screws. Check
level if desired.
4. Apply the large-print labels
to the coverplate, matching
the labels on the subbase.
1. Loosen screw terminals, insert wires
into terminal block, then re-tighten
screws.
2. Push excess wire back into the wall
opening.
3. Plug the wall opening with
nonflammable insulation to prevent
drafts from affecting thermostat
operation.
Terminal Designations
W Heat relay.
Y Compressor contactor.
G Fan relay.
O Heat pump changeover valve
energized in cooling.
Rc Cooling power. Connect to
secondary side of cooling system
transformer.
R Heating power. Connect to
secondary side of heating system
transformer.
B Heat pump changeover valve
energized in heating.
Wiring
NOTES
R & Rc terminals
In single-transformer system, leave metal
jumper in place between R & Rc. Remove
metal jumper if two-transformer system.
Heat pump systems
If wiring to a heat pump, use a small piece of
wire (not supplied) to connect terminals W
and Y.
Wire specifications
Use 18 to 22-gauge thermostat wire.
Shielded cable is not required.
R
G
W
Y
B
Rc
O
E
F
Coverplate
Subbase
Large-print
subbase switch
labels
Subbase and base installation


Specyfikacje produktu

Marka: Honeywell
Kategoria: termostat
Model: CT87K1012/E1

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Honeywell CT87K1012/E1, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje termostat Honeywell

Instrukcje termostat

Najnowsze instrukcje dla termostat

Siemens

Siemens RDG100T Instrukcja

15 Października 2024
Junkers

Junkers TA 21E Instrukcja

14 Października 2024
Oreg

Oreg AT90E Instrukcja

9 Października 2024
Oreg

Oreg AT60E Instrukcja

9 Października 2024
Heatit

Heatit PRO Instrukcja

9 Października 2024
Heatit

Heatit MULTIREG6 Instrukcja

9 Października 2024
Avidsen

Avidsen HomeFlow W Instrukcja

9 Października 2024
ORNO

ORNO OR-SH-17701 Instrukcja

8 Października 2024
ORNO

ORNO OR-SH-17702 Instrukcja

8 Października 2024
STI

STI -9102 Instrukcja

8 Października 2024