Instrukcja obsługi Honeywell CT33A

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Honeywell CT33A (16 stron) w kategorii termostat. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/16
Owner’s Manual
English: Page 1
Mode d’emploi
Français : Page 6
Manual de Uso
Español: Página 11
CT30 Series
Low-Voltage Thermostat
® U.S. Registered Trademark. Patents pending.
Copyright © 2009 Honeywell International Inc.
All rights reserved.
69-2338EFS-01
M29578
M23786
MERCURY NOTICE
If your old thermostat contains
mercury, contact your local waste
management authority for proper
disposal instructions.
TURN OFF POWER at heating/cooling system (or fuse/circuit-breaker panel).
Remove cover and thermostat, but leave wallplate with wires attached.
Is there a sealed tube containing mercury?
If so, see mercury notice below.
Leave wallplate in place.
Old thermostat Cover
Getting started
Remove your old thermostat
Check package contents:
• Thermostat
• Coverplate
• Wallanchors&screws(2each)
• Cautioncard
• Wirelabels
Before you begin, make sure you have:
• No.2Phillips&smallpocketscrewdrivers
• Hammer
• Level(optional)
• Pencil
• Drillandbit(3/16”fordrywall,7/32”for
plaster)
CT30 Series • Owner's Manual
69-2338EFS—01 2
0
0
0
M23787
Wrapsuppliedlabelssecurelyaroundeachwire.Do not let wires fall into wall opening!
IGNORE WIRE COLORS: Use only letter
designations to identify wire types.
For CT31: If your old thermostat
has 5 or more wires (not counting
terminals or C C1), you may have
purchased the wrong replacement
thermostat. Stop now and call
1-800-468-1502foradvice.
1. Pullwires
through base
(CT31only).
2. Level base if
desired.
3. Markpositions
of both screw
holes.
For : If your old CT30/CT33
thermostathas3ormorewires
( ), not counting terminals C or C1
you may have purchased the
wrong replacement thermostat.
Stopnowandcall1-800-468-1502
for advice.
Use a screwdriver to disconnect wires one by one. As you disconnect each wire, wrap it with
the label matching the letter on your old thermostat. (Adhesive labels are supplied in your
thermostat package.)
Remove the old wallplate only after all wires are labeled. Be careful not to let loose wires fall
into the wall opening.
Label wires and remove old wallplate
Mark mounting position
CT30/CT33 CT31
English: Page 1 • Français : Page 6 • Español: Página 11
3 69-2338EFS—01
M29583
M29582
1. Drillholesatpencil-marked
locations(3/16”holesfor
drywall,7/32”holesfor
plaster).
2. Use hammer to tap anchors
intoholesuntilushwithwall.
3. Optional: Pull wires through
cover plate (if needed to cover
marks left by your old thermo-
stat).
4. Connect wires rst (see page
4),theninsertscrews.Check
level if desired, then tighten
screws.
1. Drillholesatpencil-marked
locations(3/16”holesfor
drywall,7/32”holesfor
plaster).
2. Use hammer to tap anchors
intoholesuntilushwithwall.
3. Optional: Pull wires through
cover plate (if needed to cover
marks left by your old thermo-
stat).
4. Pullwiresthroughthermostat
base and insert screws.
Check level if desired, then
tighten screws.
Mount thermostat base - CT30/CT33
Mount thermostat base - CT31
Optional cover plate
Optional cover plate
Thermostat base
Thermostat base

Specyfikacje produktu

Marka: Honeywell
Kategoria: termostat
Model: CT33A

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Honeywell CT33A, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą