Instrukcja obsługi Hitec RANGER_IIN
Hitec
Sterowanie radiowe
RANGER_IIN
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hitec RANGER_IIN (4 stron) w kategorii Sterowanie radiowe. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/4
Hitec RCD Korea, Inc.
Printed in Philippines
A. TRANSMITTER
- SUPER-HETERODYNE DIGITAL PROPORTIONAL FOR EXTRA LONG RANGE
- CRYSTAL INTERCHANGEABLE
- ALL CHANNEL SERVO REVERSING SWITCHES
- CHARGER CONNECTOR FOR NI-CAD BATTERIES(8CELL 9.6V)
- LOW BATTERY WARNING L.E.D INDICATOR FOR BATTERY POWER
- NEUTRAL POSITION ADJUSTMENT FOR THROTTLE
- ALL SMT CIRCUITRY
B. RECEIVER
- BUILT IN B.E.C (BATTERY ELIMINATOR CIRCUIT)
- CRYSTAL INTERCHANGEABLE
- SIZE AND WEIGHT
SIZE : 53 X 35 X 19(mm) (2.1" X 0.8" X 1.4") , WEIGHT : 28g (0.99oz)
C. SERVO
- HEAVY-DUTY SUPER HORN
- DUST RESISTANT DESIGN
- HIGH SPEED : 0.19sec/60
- HIGH TORQUE : 3.0kg.cm(41.66oz.in)
- HI-TEC CUSTOM CHIP FOR NARROW DEADBAND
- ALL SMT CIRCUITRY
Welcome to the exciting world of R/C Modeling
Thank you for purchasing the Ranger 2N, two channel, AM radio system.
The Ranger 2N is ergonomically designed using the finest components
available and engineered to provide years of trouble-free service.
Look for the complete line of entry level, sport and competition quality
Hitec radio systems, servos, receivers, speed controls and battery
chargers at your favorite hobby dealer.
FEATURES AND SPECIFICATIONS
2 3
TRANSMITTER
ANTENNA
CARRYING HANDLE
POWER L.E.D
THROTTLE
CONTROL STICK
STEERING TRIM
LEVER
STEERING
CONTROL STICK
TRANSMITTER
CRYSTAL
THROTTLE
TRIM LEVER
CHARGING
JACK
STEERING SERVO REVERSE SWITCH
POWER ON/OFF
SWITCH
THROTTLE SERVO
REVERSE SWITCH
NEUTRAL POSITION
ADJUSTMENT LEVER
X-TAL
FREQUENCY FLAG
Set-up and installation of your new Ranger 2N
Please read the following section carefully before
attempting to install the Ranger 2N system
When installing the system in the model of your choice, please follow the
detailed instructions found in the model kit.
1. The transmitter requires eight and the receiver battery pack needs four
AA size batteries. These can be Alkaline or Ni-cad cells. If you choose to
install Ni-cad batteries, the optional CG-25A(110V)or CG-22(220V)
Hitec overnight wall charger can be used to re-charge them.
2. When loading the batteries, make sure the receiver and transmitter switches
are in the "off" position.
3. Open the battery door in the back of the transmitter by squeezing the tab on the
bottom of the battery door and lifting up.
4. Load batteries into the appropriate slots, taking care to install according to the
proper polarity.
5. Replace the battery door and turn the power "on". If the batteries are fresh and
charged, the green L.E.D. will be lit. Should the battery power drop to an unacceptable
level, the red L.E.D. will glow, warning the user of impending failure. At this point,
replace the alkaline cells or charge the batteries if they are Ni-cads.
1. Install the receiver to protect it from vibration and potential crash damage.
2. Typically one servo will be used for the steering and the other servo will be
used to operate a mechanical speed control, or not used at all and an optional
electronic speed control will be used.
3. If your vehicle is electric, there will be a proportional speed control you will wish
to use. If your speed control is mechanical, it will require a servo to operate it.
The battery and switch harness found in the kit must also be used to provide the
receiver with power.
4. Should your model use an electronic speed control that has the option of the
B.E.C. circuit (battery eliminator circuit), this feature will eliminate the receiver
battery and use the motor battery to feed the receiver and servos through the
speed control.
5. Please refer to the instructions that accompany your electronic
speed control for installation.
BATTERY INSTALLATION
RADIO SYSTEM INSTALLATION
4 5
PRESS BOTTOM AND
OPEN UPWARD
BATTERY COVER
8 AA SIZE BATTERY. BE
CAREFUL TO LOAD RIGHT
DIRECTION OF BATTERIES( + - )
(Electronic Speed Control)
Specyfikacje produktu
| Marka: | Hitec |
| Kategoria: | Sterowanie radiowe |
| Model: | RANGER_IIN |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Hitec RANGER_IIN, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Sterowanie radiowe Hitec
25 Września 2024
23 Września 2024
22 Września 2024
22 Września 2024
18 Września 2024
15 Września 2024
13 Września 2024
13 Września 2024
12 Września 2024
11 Września 2024
Instrukcje Sterowanie radiowe
- Sterowanie radiowe Spektrum
- Sterowanie radiowe Reely
- Sterowanie radiowe Futaba
- Sterowanie radiowe Graupner
- Sterowanie radiowe Multiplex
- Sterowanie radiowe Robbe Futaba
- Sterowanie radiowe Robbe
- Sterowanie radiowe JRpropo
- Sterowanie radiowe Sanwa
- Sterowanie radiowe Rush
Najnowsze instrukcje dla Sterowanie radiowe
14 Października 2024
27 Września 2024
27 Września 2024
27 Września 2024
27 Września 2024
27 Września 2024
27 Września 2024
27 Września 2024
26 Września 2024
26 Września 2024