Instrukcja obsługi Hitachi CMP402HDU
Hitachi
Monitory plazmowe
CMP402HDU
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hitachi CMP402HDU (35 stron) w kategorii Monitory plazmowe. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/35
i
SAFETY GUIDELINES
ENGLISH
This monitor is designed to be safe to use. However, due to high voltage of about 400 V,
fire or serious injury may occur unless you use this monitor in correct way.
You are strongly suggested to follow the instruction shown below in order to avoid such
injury.
Keep the safety guideline
Do not use the monitor if it fails
If you find something unusual ,
If smoke comes out,
If there is a strange smell,
If water enters the case,
If you drop the monitor or
damage the cabinet,
Turn off the monitor
Disconnect the power
plug from the power point
Request for repair
Warning and Caution are indicated in this guide and monitor itself.
Fire or electric shock may cause death or serious injury unless you
follow the instruction.
Warning
Electric shock or other accidents may cause serious injury or damage
of your properties.
Caution
ENGLISH
ii
If something smells strange or smoke comes from the monitor:
Turn off the monitor and disconnect the power plug from the power point immediately.
Contact service center after confirming that the smoking has stopped.
If you continue to operate the monitor with such abnormal condition, it may cause fire
or you may receive an electric shock.
Do not drop water or a foreign substance on to the monitor.
If you drop water or a foreign substance on to the monitor, it may cause fire or an
electric shock.
If it happens turn off the monitor and disconnect the power plug from the power point
and ask service center for instruction.
Do not put the monitor on an unstable place.
If you put the monitor on an uneven or unstable place, it may fall down and you may be
injured.
Put the monitor on a flat surface strong enough to take the weight.
Do not apply shock to the monitor.
If no picture, glass broken, smoke or something is smelling after applying shock to the
monitor, turn off the monitor and disconnect the power plug from the power point
immediately. Then, call the service center.
If you continue to operate the monitor with such abnormal conditions, it may cause fire
or you may receive an electric shock.
Do not disassemble or modify the monitor.
There is high voltage portion inside of the monitor. Disassembling or modification of the
monitor may cause fire or electric shock.
Do not use the monitor in wet environment.
If you use the monitor in a wet place such as bath or shower room, it may cause fire or
electric shock. Using the monitor beside a window when snowing or raining or by a
seaside are not recommended.
Do not damage or modify the power cord.
If you put something heavy on the power cord or pull, squeeze, heat the cord, it may be
damaged and it may cause fire or electric shock.
If the power cord is damaged, call service center.
Fire or electric shock may cause death or serious injury unless you
follow the instruction below.
Warning
SAFETY GUIDELINES(continued)
ENGLISH
iii
Fire or electric shock may cause death or serious injury unless you
follow the instruction.
Warning
The enclosed power cord must be used!
Failure to do so may cause electric shock hazard or fire hazard.
In USA/Canada, use a UL LISTED/CSA LABELLED or CERTIFIED power cord set
meeting the following specifications :
Rating: min. 125V, 10A , Length: max. 3.0m , Type: SVT or SJT
Plug type: NEMA 5-15P figure, Parallel blade, Grounding type
In Europe, a proper European standard approved power cord is to be used with this
monitor.
For a rated current up to 6 A, a type not lighter than H05VV-F 3G 0.75 mm2 or
H05VVH2-F 3G 0.75 mm2 must be used.
Use only the correct voltage power outlet with safety ground connection!
100 - 120 V for USA, Canada, etc.
200 - 240 V for Europe, etc.
(This monitor will automatically adjust to the input voltage 100 - 120 / 200 - 240V.)
Be careful of power cord connection!
Before inserting the plug of the power cord into a socket of the correct voltage, check
that the connection portion of the power cord is clean (with no dust). Then, insert the
plug of power cord into the socket firmly, otherwise it may cause electric shock or fire
hazard.
Do not touch the power plug when lightning is close to you.
You may receive an electric shock.
Do not touch the power plug with wet hands.
You may receive an electric shock.
Do not obstruct a ventilation hole.
If you obstruct a ventilation hole during the operation of the monitor or just after
switching off the power, it may cause a fire or electric shock due to heating up the
monitor.
Do not put the monitor screen side up.
Do not put the monitor on a shelf or in a cabinet.
Do not put the monitor on a carpet or mattress.
Do not cover the monitor with a cloth.
Specyfikacje produktu
| Marka: | Hitachi |
| Kategoria: | Monitory plazmowe |
| Model: | CMP402HDU |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Hitachi CMP402HDU, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Monitory plazmowe Hitachi
13 Października 2024
10 Października 2024
9 Sierpnia 2024
9 Sierpnia 2024
6 Lipca 2024
4 Lipca 2024
3 Lipca 2024
Instrukcje Monitory plazmowe
Najnowsze instrukcje dla Monitory plazmowe
12 Października 2024
4 Lipca 2024
3 Lipca 2024
3 Lipca 2024