Instrukcja obsługi HiKOKI GP13
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla HiKOKI GP13 (17 stron) w kategorii Sander. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/17
Grinder
手提電磨機
เครื่องเจียร
GP 13
Handling instructions
使用說明書
คูมือการใชงาน
Read through carefully and understand these instructions before use.
使用前務請詳加閱讀
โปรดอานโดยละเอียดและทําความเขาใจกอนใชงาน
1
1 2
3
English 中國語 ไทย
1Wheel guard 砂輪保護裝置 กําบังหินเจียร
2Grinding wheel 砂輪 หินเจียร
3Nose bracket 鼻形支撐架 โครงยึดเครื่องมือ
4Hanger 挂耳 ที่แขวน
5Brush cap 刷子蓋 ฝาแปรงถาน
6Stopper 制動器 สต็อปเปอร
7Switch trigger 觸動開關 สวิทซไก
8Nut M12 M12螺帽 น็อต M12
9Wheel washer 輪墊圈 แหวนหินเจียร
0Spindle detent hole 主軸銷鍵孔 ชองแกนเพลา
!Wear limit 磨損極限 ขอบเขตการสึกหรอ
@No. of carbon brush 碳刷號 จํานวนแปรงถาน
1
23
4 5
679
0
8
2
!
@
38
6 mm
17 mm
English
2
GENERAL SAFETY RULES
WARNING!
Read all instructions
Failure to follow all instructions listed below may result in
electric shock, fi re and/or serious injury.
The term “power tool” in all of the warnings listed below
refers to your mains operated (corded) power tool or battery
operated (cordless) power tool.
SAVE THESE INSTRUCTIONS
1) Work area
a) Keep work area clean and well lit.
Cluttered and dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
fl ammable liquids, gases or dust.
Power tools create sparks which may ignite the dust
of fumes.
c) Keep children and bystanders away while
operating a power tool.
Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adapter plugs with earthed
(grounded) power tools.
Unmodifi ed plugs and matching outlets will reduce
risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators.
There is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions.
Water entering a power tool will increase the risk
of electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts.
Damaged or entangled cords increase the risk of
electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces
the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired
or under the infl uence of drugs, alcohol or
medication.
A moment of inattention while operating power
tools may result in serious personal injury.
b) Use safety equipment. Always wear eye
protection.
Safety equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c) Avoid accidental starting. Ensure the switch is in
the off position before plugging in.
Carrying power tools with your fi nger on the
switch or plugging in power tools that have the switch
on invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on.
A wrench or a key left attached to a rotating part
of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times.
This enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts.
Loose clothes, jewellery or long hair can be caught in
moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used.
Use of these devices can reduce dust related
hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application.
The correct power tool will do the job better and safer
at the rate for which it was designed.
b) Do not use the power tool if the switch does not
turn it on and off .
Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
c) Disconnect the plug from the power source
before making any adjustments, changing
accessories, or storing power tools.
Such preventive safety measures reduce the risk
of starting the power tool accidentally.
d) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and
any other condition that may aff ect the power
tools operation.’
If damaged, have the power tool repaired before
use.
Many accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
g) Use the power tool, accessories and tool bits
etc., in accordance with these instructions and
in the manner intended for the particular type
of power tool, taking into account the working
conditions and the work to be performed.
Use of the power tool for operations diff erent from
intended could result in a hazardous situation.
5) Service
a) Have your power tool serviced by a qualifi ed
repair person using only identical replacement
parts.
This will ensure that the safety of the power tool
is maintained.
PRECAUTION
Keep children and infi rm persons away.
When not in use, tools should be stored out of reach of
children and infi rm persons.
Specyfikacje produktu
Marka: | HiKOKI |
Kategoria: | Sander |
Model: | GP13 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z HiKOKI GP13, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Sander HiKOKI
29 Września 2024
26 Września 2024
24 Września 2024
24 Września 2024
8 Sierpnia 2024
8 Sierpnia 2024
Instrukcje Sander
- Sander AEG
- Sander Worx
- Sander Milwaukee
- Sander Bosch
- Sander Parkside
- Sander Global
- Sander Toolcraft
- Sander Festool
- Sander Bavaria By Einhell
- Sander Stanley
- Sander Black & Decker
- Sander Scheppach
- Sander Proxxon
- Sander Ribimex
- Sander Hazet
- Sander RIKON
- Sander DeWalt
- Sander Einhell
- Sander Hyundai
- Sander Silverline
- Sander Makita
- Sander Ozito
- Sander RYOBI
- Sander Flex
- Sander Biltema
- Sander Hilti
- Sander Trotec
- Sander Dremel
- Sander Handwerk
- Sander Meec Tools
- Sander Güde
- Sander Arendo
- Sander Bavaria
- Sander Gastroback
- Sander DURO PRO
- Sander McKenzie
- Sander Westfalia
- Sander Ergotools Pattfield
- Sander Fein
- Sander Ferm
- Sander Hitachi
- Sander Herkules
- Sander Craftsman
- Sander Matrix
- Sander Fieldmann
- Sander Ridgid
- Sander PowerPlus
- Sander Alpha Tools
- Sander Vonroc
- Sander Workzone
- Sander Porter-Cable
- Sander Metabo
- Sander Skil
- Sander Kinzo
- Sander Far Tools
- Sander Tryton
- Sander Tacklife
- Sander Maktec
- Sander Bort
- Sander Power Craft
- Sander Topcraft
- Sander Gamma
- Sander Duro
- Sander Varo
- Sander Max
- Sander Truper
- Sander Bruder Mannesmann
- Sander Meister Craft
- Sander Rupes
- Sander Batavia
- Sander Protool
- Sander Holzmann
- Sander Black Decker
- Sander Stomer
- Sander Elu
- Sander King Craft
- Sander Powertec
- Sander Toolson
- Sander Toledo
- Sander FIXIT
- Sander Einhell Bavaria
- Sander THUN
- Sander Pevec
- Sander TAURUS Titanium
- Sander Stalco
Najnowsze instrukcje dla Sander
14 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
7 Października 2024
7 Października 2024
7 Października 2024
7 Października 2024