Instrukcja obsługi Hatco HZMH-30D

Hatco Płyta rozgrzewająca HZMH-30D

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hatco HZMH-30D (4 stron) w kategorii Płyta rozgrzewająca. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

Heated Zone Merchandisers

HZMH and HZMS Series

Installation and Operating Manual

P/N 07.04.569.00

(see page 2)

www.hatcocorp.com

Do not operate this equipment unless you

have read and understood the contents of

this manual! Failure to follow the

instructions contained in this manual may

result in serious injury or death. This

manual contains important safety

information concerning the maintenance,

use, and operation of this product. If

you’re unable to understand the contents

of this manual, please bring it to the

attention of your supervisor. Keep this

manual in a safe location for future

reference.

No opere este equipo al menos que haya

leído y comprendido el contenido de este

manual! Cualquier falla en el seguimiento

de las instrucciones contenidas en este

manual puede resultar en un serio lesión

o muerte. Este manual contiene

importante información sobre seguridad

concerniente al mantenimiento, uso y

operación de este producto. Si usted no

puede entender el contenido de este

manual por favor pregunte a su

supervisor. Almacenar este manual en

una localización segura para la referencia

futura.

Ne pas utiliser cet équipement sans avoir

lu et compris le contenu de ce manuel !

Le non-respect des instructions

contenues dans ce manuel peut entraîner

de graves blessures ou la mort. Ce

manuel contient des informations

importantes concernant l'entretien,

l'utilisation et le fonctionnement de ce

produit. Si vous ne comprenez pas le

contenu de ce manuel, veuillez le signaler

à votre supérieur. Conservez ce manuel

dans un endroit sûr pour pouvoir vous y

référer plus tard.

WARNING

ADVERTENCIA

AVERTISSEMENT

Model Voltage Watts Amps

Overhead

Zones Plug Configuration

HZMH-24D 120 1500 12.5 4 NEMA 5-20P

HZMH-30D 120/208–240 2700 11.3 8 NEMA L14-20P

HZMH-36D 120/208–240 2800 11.7 8 NEMA L14-20P

HZMH-42D 120/208–240 2900 12.1 8 NEMA L14-20P

HZMH-48D 120/208–240 3000 12.6 8 NEMA L14-20P

HZMH-54D 120/208–240 4200 17.6 12 NEMA L14-30P

HZMH-60D 120/208–240 4300 18.0 12 NEMA L14-30P

Model Voltage Watts Amps

Overhead

Zones Plug Configuration

HZMH-24 120 750 6.3 2 NEMA 5-15P

HZMH-30 120 1350 11.3 4 NEMA 5-15P

HZMH-36 120 1400 11.7 4 NEMA 5-15P

HZMH-42 120 1450 12.1 4 NEMA 5-20P

HZMH-48 120 1500 12.5 4 NEMA 5-20P

HZMH-54 120 2100 17.5 6 NEMA 5-30P

HZMH-60 120 2150 17.9 6 NEMA 5-30P

Form No. HZMM-0812 5

SPECIFICATIONS

Electrical Rating Chart — HZMH-XX Models (Horizontal Single Shelf)

Electrical Rating Chart — HZMH-XXD Models (Horizontal Dual Shelf)

Plug Configurations

Units are equipped with an electrical cord and plug appropriate

for the electrical rating of the unit and must be connected to a

dedicated circuit.

ELECTRIC SHOCK HAZARD: Plug unit into a properly

grounded electrical receptacle of the correct voltage, size,

and plug configuration. If plug and receptacle do not

match, contact a qualified electrician to determine and

install proper voltage and size electrical receptacle.

NOTE: The specification label is located on the side of the

control enclosure. See the label for the serial number

and verification of unit electrical information.

WARNING

Plug Configurations

NOTE: Receptacle not supplied by Hatco.

NEMA 5-15P NEMA 5-20P

NEMA L14-20P NEMA L14-30P

Form No. HZMM-0812 11

OPERATION

General

Heated Zone Merchandisers are setup at the factory for energy-

saving, automatic operation (Auto Mode ). Refer to “Factory

Setpoints” in the SPECIFICATIONS section for factory setpoint

information. Use the following information and procedures to

operate a Heated Zone Merchandiser.

Read all safety messages in the IMPORTANT SAFETY

INFORMATION section before operating this equipment.

Do not place food product directly onto hardcoat surface.

Food product must be wrapped, boxed, or on a food pan.

Do not slide pans across hardcoat surface, use rough-

bottomed pans, or drop anything on hardcoat surface.

Scratching may occur. Damage to hardcoat surface caused

by misuse is not covered under warranty.

Theory of Operation

The Heated Zone Merchandiser is designed for efficient and

environmentally-friendly operation by heating specific “zones”

only when product is present. The operation of the Heated Zone

Merchandiser is controlled by a series of optical sensors and

the LCD controller. The sensors are located along the sides of

each hardcoat shelf. Larger units have additional sensors

located in zone dividers that separate each shelf into multiple

overhead heat zones.

For all sizes of units, each hardcoat shelf is equipped with

separate front and rear heating elements. These two elements

operate independently in Auto Mode .

The number of overhead ribbon heating elements is determined

by the size of the unit. The overhead elements above each

hardcoat shelf are considered individual heat zones. This means

that the number of zones on each shelf is either two, four, or

six—depending on the size of the unit. Each overhead element

operates independently in Auto Mode .

NOTE: Each shelf on a Heated Zone Merchandiser can be set

to a different operating mode.

Auto Mode Operation

At startup in Auto Mode operation, all shelf heating elements

and overhead heating elements in an empty Heated Zone

Merchandiser will be in . The front and rear shelfStand-By

elements will heat at their Stand-By power percentage to the

setpoint temperature. All overhead elements remain off. When

product is placed on a shelf, the optical sensors signal the LCD

controller, and the controller activates the appropriate shelf

elements and overhead elements. Each of the shelf elements

affected by the placement of product will heat at full wattage to

the setpoint temperature. Each of the overhead elements

affected by the placement of product will heat at its setpoint

power percentage. All affected elements will remain activated

until all product is removed from the “zone.” Anytime a zone is

emptied of product, the zone will return to Stand-By.

On Mode Operation

At startup in On Mode operation, all shelf heating elements will

heat at full wattage to the setpoint temperature, and all

overhead heating elements will heat at their setpoint power

percentage. All shelf elements will remain at full wattage and

all overhead elements will remain at their setpoint power

percentage the entire time the unit is on.

WARNING

NOTICE

Off Mode Operation

At startup in Off Mode operation, all shelf heating elements and

overhead heating elements are disabled. Only the LED lights

above each shelf will illuminate. This mode provides ambient

lighting for the display of non-heated product.

Startup

1. Move the Power ON/OFF (I/O) switch to the ON (I) position.

• The LED lights will illuminate.

• The LCD controller will startup. After the startup screens

and during operation, the display will cycle through the

overhead heat zones showing their current status and

temperature.

• Auto Mode = All shelf elements will heat at Stand-By

power percentage to the setpoint temperature. All

overhead elements remain off.

On Mode = All shelf elements will heat at full wattage to

the setpoint temperature. All overhead elements will heat

at their setpoint power percentage.

Off Mode = All heating elements are disabled—for

ambient lighting only.

HZM Series Control Panel

NOTE: If the warning light comes on at any time, the unit is

overheating/malfunctioning. Turn off and unplug the

unit. Contact an Authorized Service Agent or Hatco for

assistance.

BURN HAZARD: Some exterior surfaces on unit will get

hot. Use caution when touching these areas.

2. Place pre-heated, wrapped food product onto the desired

shelf.

• Auto Mode = The optical sensors will signal the LCD

controller, and the controller will activate the appropriate

zone(s).

3. Continue to load and empty the shelves on the unit as

desired.

• Auto Mode = The various zones in the unit will adjust

automatically to the levels of product on the

shelves—ensuring maximum efficiency.

NOTE: To change the shelf setpoint temperature(s), element

power percentages, or the operating mode, refer to the

appropriate procedure in this section.

Shutdown

1. Move the Power ON/OFF (I/O) switch to the OFF (O)

position. All LED lights, heating elements, and the LCD

controller will shut off.

Display

Power ON/OFF (I/O) Switch

Warning

Light LCD Controller

CAUTION

Specyfikacje produktu

Marka:	Hatco
Kategoria:	Płyta rozgrzewająca
Model:	HZMH-30D

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Hatco HZMH-30D, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Płyta rozgrzewająca Hatco

Hatco Ultra-Glo UGFFBL Instrukcja

23 Września 2024

Hatco HZMS-60D Instrukcja

23 Września 2024

Hatco Glo-Ray GRS-54-I Instrukcja

23 Września 2024

Hatco IHDCH-28 Instrukcja

22 Września 2024

Hatco HZMH-60 Instrukcja

22 Września 2024

Hatco IHDCH-45 Instrukcja

22 Września 2024

Hatco Glo-Ray GRS-24-I Instrukcja

22 Września 2024

Hatco HZMH-60D Instrukcja

22 Września 2024

Hatco Glo-Ray GRPWS-3618Q Instrukcja

22 Września 2024

Hatco HSBF-GL-3018 Instrukcja

22 Września 2024

Instrukcje Płyta rozgrzewająca

Najnowsze instrukcje dla Płyta rozgrzewająca

Royal Catering RC-SHSFL09 Instrukcja

14 Października 2024

Hendi 238868 Instrukcja

9 Października 2024

Rommelsbacher WPR 307/E Instrukcja

8 Października 2024

Salton ICS2146 Instrukcja

7 Października 2024

Salton TWT30 Instrukcja

7 Października 2024

Salton SMW2094BKW Instrukcja

7 Października 2024

Salton SP2111 Instrukcja

7 Października 2024

Bartscher WP230S-EB 1/1S Instrukcja

7 Października 2024

BEEM Buffet Star 2 in 1 Instrukcja

5 Października 2024

Brentwood BF-215 Instrukcja

4 Października 2024