Instrukcja obsługi Hammond XMc-2
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hammond XMc-2 (12 stron) w kategorii organ. Ta instrukcja była pomocna dla 17 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/12
Model :/E
Owner’s Manual
*#1 *#1
*#1 *#1
*#1
Thank you, and congratulations on your choice of
a Hammond XMc-2, Drawbar Controller.
In order to get the most out of this instrument for
many years to come, please take the time to read
this manual in full.
*#1 :/Owner’s Manual
IMPORTANT SAFETY INSTRUCTIONS
In case if in the future your instrument gets too old to
play/use or malfunctions beyond repair, please observe
the instructions of this mark, or, if any question, be sure
to contact your dealer or your nearest town or municipal
office for its proper disposal.
Before using this unit, please carefully read this “Safety Instructions” and use it correctly.
Please be sure to keep this manual at hand even after reading it once.
This “Safety Instructions” section contains very important points for securing your safety. Strictly observe the instructions, please.
In this manual, the degrees of dangers and damages are classified and explained as follows:
WARNING This sign is for alerting the user there is a risk of death or severe injury if this unit is not
properly used as instructed.
This sign is for alerting the user there is a risk of injury or material damage if this unit
is not properly used as instructed.
* Material damage here means a damage to the room, furniture or animals or pets.
CAUTION
Do not open (or modify in any way) the unit.
Do not attempt to repair the unit, or replace parts in it (except
when this manual provides specific instructions directing you
to do so). Refer all servicing to your retailer, the nearest
Hammond, or an authorized Hammond distributor, as listed
on the “Service” page.
Never use or store the unit in places that are:
Subject to temperature extremes (e.g., direct sunlight in
an enclosed vehicle, near a heating duct, on top of heat-
generating equipment); or are
Damp (e.g., baths, washrooms, on wet floors);
or are
Humid; or are
Exposed to rain; or are
Dusty; or are
Subject to high levels of vibration.
Be sure to use only the connecting cord supplied with the unit.
Do not excessively twist or bend the connecting cord, nor place
heavy objects on it. Doing so can damage the cord, producing
severed elements and short circuits. Damaged cords are fire
and shock hazards!
Do not allow any objects (e.g., flammable material, coins,
pins); or liquids of any kind (water, soft drinks, etc.) to pen-
etrate the unit.
Immediately turn the power off, remove the AC adaptor from
the outlet, and request servicing by your retailer, the nearest
Hammond, or an authorized Hammond distributor, as listed
on the “Service” page when:
The AC adaptor, the power-supply cord, or the plug has
been damaged; or
If smoke or unusual odor occurs
Objects have fallen into, or liquid has been spilled onto
the unit; or
The unit has been exposed to rain (or otherwise has be-
come wet); or
The unit does not appear to operate normally or exhibits a
marked change in performance.
In households with small children, an adult should provide
supervision until the child is capable of following all the rules
essential for the safe operation of the unit.
Protect the unit from strong impact.
(Do not drop it!)
Do not put anything that contains water (e.g., flower vases)
on this unit. Also, avoid the use of insecticides, perfumes, al-
cohol, nail polish, spray cans, etc., near the unit. Swiftly wipe
away any liquid that spills on the unit using a dry, soft cloth.
WARNING
The unit should be located so their location or position does
not interfere with their proper ventilation.
Always grasp only the plug on the AC adaptor cord when plug-
ging into, or unplugging from, an outlet or this unit.
Try to prevent cords and cables from becoming entangled.
Also, all cords and cables should be placed so they are out of
the reach of children.
Never climb on top of, nor place heavy objects on the unit.
Before moving the unit, disconnect the AC adaptor and all
cords coming from external devices.
CAUTION
*#1 :/EOwner’s Manual
3
TOP PANEL
1. DRAWBARS
Controls harmonics of the part that is selected by the
DRAWBAR Button (6). The setting of the Drawbars is
called “Registration”.
2. OVERDRIVE Knob
Controls the Distortion of the Upper and Lower part.
3. O.D. ON Button
Switches ON/OFF the Overdrive effect.
4. REVERB Knob
Controls the depth of the Reverb effect.
5. PERC Button
Switches the Percussion voice.
6. DRAWBAR Button
This button selects Registration Parts. Also activate Draw-
bars (1).
7. PRESET Buttons
Recalls the selected Patches.
8. VIBRATO & CHORUS Buttons
Switch the Vibrato and Chorus effects.
9. LESLIE Buttons
Switch the Leslie effect.
REAR PANEL
10. MIDI IN Jack
This is the Input Jack for the MIDI Keyboard.
11. TO XM-2 Jack
This Jack is for connecting the XM-2 to this unit by the
attached HMC-1 cable.
NAMES AND FUNCTIONS
1
2
3
4
5
67
8 9
10 11
Specyfikacje produktu
| Marka: | Hammond |
| Kategoria: | organ |
| Model: | XMc-2 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Hammond XMc-2, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje organ Hammond
23 Maja 2024
Inne instrukcje Hammond
19 Września 2024
18 Września 2024
17 Września 2024
17 Września 2024
17 Września 2024
6 Lipca 2024
23 Maja 2024