Instrukcja obsługi Haier DW9-AFM

Haier zmywarka DW9-AFM

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Haier DW9-AFM (12 stron) w kategorii zmywarka. Ta instrukcja była pomocna dla 11 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/12

Cleaning and Special Maintenance

Filter Assembly

For the best performance and results, the filter assembly must

be cleaned.

The filter efficiently removes food particles from the wash water,

allowing it to be recirculated during the cycle. For this reason, it

is a good idea to remove the larger food particles trapped in the

filter after each wash cycle by rinsing the "A" semi-circular filter

and cup under running water. To remove the filter assembly, pull

on the cup handle in the upward direction. The entire filter as-

sembly (made up of the "A" semicircular filter and the "B" fine

filter) should be cleaned at least once a month. To clean the filter

and the fine filter, use a cleaning brush. Then, reassemble the

filter parts as shown in the figures below and reinsert the entire

assembly in the dishwasher, positioning in its seat and pressing

downward.

The dishwasher must never be used without the filters. Improper

replacement of the filters may reduce level of the appliance and

damage dishes and utensils.

Cleaning the Spray Arms

It may happen that food particle become encrusted on the sprayer

arms and block the hole. Check the sprayer arms periodically

and clean them when needed. (See "Close up view [interior]" ,

letters C-E ).

Cleaning the Water Inlet Filter

Periodically clean the water inlet filter (see figure 1/A) located on

the outlet of the water supply tap.

After turning off the water tap, unscrew the end of the water sup-

ply hose, remove the filter and clean it carefully under running

water. Then, return the filter to its place and tighten the water

supply hose back into position.

Installation

Positioning the Appliance

Position the appliance in the desired location. The back should

rest against the wall behind it, and the sides, along the adjacent

cabinets or wall. The dishwasher is equipped with water supply

and drain hoses that can be positioned to the right or the left to

facilitate proper installation.

Levelling the Appliance

Once the appliance is positioned, adjust the feet (screwing them

in or out) to adjust the dishwasher, making it level. In any case,

the appliance should not be inclined more than 2 . If the appli-

ance is level, it will help ensure proper performance.

Cold Water Connection

Connect the cold water supply hose to a threaded 3/4 (gas) con-

nector and make sure that it is fastened tightly in place (see fig.

1).

If the water pipes are new or have not been used for an extended

period of time, let the water run to make sure that the water is

clear and free of impurities. If this precaution is not taken, there

is a risk that the water inlet can get blocked and damage the

appliance.

Hot Water Connection

The water supply to the appliance can also be connected to the

house's hot water line (centralised system, heating system), as

long as it does not exceed a temperature of 60 .

In this case, the wash cycle time will be shortened by about 15

minutes and the wash efficiency slightly reduced.

The connection must be made to the hot water line following the

same procedures as those for the connection to the cold water

line.

Drain Hose Connection

Insert the drain hose into a drain pipe with a minimum diameter

of 4cm, or let it run into the sink, making sure to avoid bending

or crimping it. Use the special plastic support that comes with

the appliance (see fig.2). The free end of the hose must be at a

height between 40 and 100 cm and must not be immersed in

water.

Attention:

The special plastic hose support must be solidly fastened to

the wall to prevent the drain hose from moving and allowing

water to spill outside the drain.

Electrical Connection

After making sure that the voltage and frequency values for the

current in the home correspond to those on the rating plate

(located on the stainless steel inner door of the appliance) and

that the electrical system is sized for the maximum voltage on

the rating plate, insert the plug into an electrical socket which

is earthed properly (the earthing of the appliance is a safety

requirement mandated by law).

If the electrical socket to which the appliance must be connected

is not appropriate for the plug, replace the plug, rather than

using adaptors or the like as they could cause overheating and

burns.

MAX 100 MIN 40

fig.2

Troubleshooting

It may occur that the dishwasher does not function or does not

function properly. Before calling for assistance, let us see what

can be done first: have you forgotten to press one of the buttons

or to perform an essential operation?

The Dishwasher Does Not Start

Have you checked whether:

- the plug is pushed into the socket correctly;

- the power is on in the house;

- the door is closed properly;

- the ON-OFF switch is on "ON";

- the water supply is turned on.

The Dishwasher Does Not Load Water

Have you checked whether:

- the water is turned on and the hose is

connected properly;

- the water supply to the house on and has

sufficient pressure;

- the water supply hose is crimped or bent;

- the filter for the water supply hose is clogged.

The Dishes Are Not Clean

Have you checked whether:

- the water is turned on and the hose is

connected properly;

The Dishwasher Does Not Drain

Have you checked whether:

- the drain hose is crimped or bent.

Lime Deposits or a White Film Form on the Dishes

Have you checked whether:

- the lid to the salt container is closed properly;

- the rinse aid dosage is correct.

If, despite all these checks, the dishwasher still does not function

and/or the problem persists, contact the nearest authorised ser-

vice centre and provide them with the following information:

- the nature of the problem;

- the model type number (Mod...) And the serial number (S/N...),

which are indicated on the plate located on the side of the inner

part of the door.

Never call on unauthorised technicians and refuse to

allow parts to be installed that are not original spare

parts.

- the water supply to the house on and has

sufficient pressure;

- the water supply hose is crimped or bent;

- the filter for the water supply hose is clogged.

.10.

.9. GB

Fig.1

- It is important to try and run the dishwasher when it is fully

loaded to save on energy. In order to prevent odors from form-

ing and food from caking onto the dishes, you can run the hold

cycle.

- Choose the right wash cycle: the choice of cycle depends on

the type of dishware, cookware and utensils being washed and

how dirty they are.

Energy Saving Tips

- Use the right amount of detergent: if you use too much detergent,

the result will not be cleaner dishes, but, rather, a greater nega-

tive impact on the environment.

- There is no utility in rinsing dishes, cookware and untensils

before placing them in the dishwasher.

How to Keep Your Dishwasher in Shape

After Every Wash

After every wash, turn off the water supply to the appliance and

leave the door slightly ajar so that moisture and odors are not

trapped inside.

Remove the Plug

Before cleaning or performing maintenance, always remove the

plug from the socket. Do not run risks.

No Solvents or Abrasive Cleaning Products

To clean the exterior and rubber parts of the dishwasher, do not

use solvents or abrasive cleaning products. Rather, use only a

cloth and warm soap water.

To remove spots or stains from the surface of the interior, use a

cloth dampened with water and a little white vinegar, or a clean-

ing products made specifically for dishwasher.

When You Go on Holiday

When you go on holiday, it is recommended that you run a wash

cycle with the dishwasher empty and then remove the plug from

the socket, turn off the water supply and leave the door of the

appliance slightly ajar. This will help the seals last longer and pre-

vent odors from forming within the appliance.

Moving the Appliance

If the appliance must be moved, try to keep it in the vertical position.

If absolutely necessary, it can be positioned on its back.

Seals

One of the factors that cause odors to form in the dishwasher is

food that remains trapped in the seals. Periodic cleaning with a

sponge will prevent this from occurring.

Wash Cycle Table

.8.

.7. GB

Cycle Cycle Selection

Information

Description of

Cycle

Deter-

gent

Rinse

Aid

Intensive

Wash

Glassware

Soak

Very dirty dishes, pots and

pans. (not to be used with

delicate items)

Economic, fast cycle to be

used for items which are sen-

sitive to higher. Run immedi-

ately after dishes are used.

Pre-wash of dishes, pots and

pans while waiting for the

load to be completed after

the subsequent meal.

Pre-wash with cold water.

Rinse with cold water.

Extended wash at 50

Rinse with hot water

Drying.

Wash at 50 .

Hot Rinse

Drying.

Short cold wash to prevent

food residue from drying on

the dishes

30g

15g

N o r m a l W a s h

(IEC-EN50242)

25g

Normally dirty dishes, pots

and pans. Standard daily

cycle.

Rinse with cold water.

Extended wash at 50

Rinse with hot water

Drying.

Rinse

For dishes that need to be

rinsed and dried only.

Rinse with hot water

Drying.

Specyfikacje produktu

Marka:	Haier
Kategoria:	zmywarka
Model:	DW9-AFM
Położenie urządzenia:	Wolnostojący
Wysokość produktu:	850 mm
Szerokość produktu:	450 mm
Głębokość produktu:	600 mm
Funkcja AquaStop:	Tak
Ilość programów piorących:	5
Poziom hałasu:	55 dB
Pobór wody na cykl:	14 l
Zużycie energii na cykl:	0.95 kWh
Kategoria prania:	B
Kategoria suszenia:	B