Instrukcja obsługi Gossen Metrawatt SECULIFE ST HV

Gossen Metrawatt Przyrządy pomiarowe SECULIFE ST HV

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Gossen Metrawatt SECULIFE ST HV (72 stron) w kategorii Przyrządy pomiarowe. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/72

SECULIFE⏐ST and SECULIFE⏐ST HV

Test Instruments for Portable Appliance Testing according to Health and Safety Policy

and in Accordance with the Medical Product Law as well as for Routine Testing

3-349-448-03

21/7.15

Operating Instructions

2GMC-I Messtechnik GmbH

PROBE 54

SONDE

Auto

Function

Test

VAux Setup

Iso /

I leakage

BDFHK

AC E G I

Applied Parts

45678910

14 15 1816 17

Probe connection

Insert the double plug of the probe into sockets 4 and

5 such that the plug with the white ring contacts

socket 5 (vertical bar).

Note: Contact problems with exposed conductive parts

when using the standard probe with test tip

In order to assure good contact, surface coatings must be

removed from devices under test with special tools at a suit-

able location so that the surface has a metallic shine. The tip

of the test probe is not suitable for scratching away paint, be-

cause this may impair its coating and/or mechanical

strength. The brush probe (Z745G) may be more suitable

than the test probe in certain individual cases.

Measurements at jacks 1 – 2 – 3

Always start with the measurement before contacting

the measuring point. Between jacks 1 and 2, a maxi-

mum of 10 V may be applied. Between jacks 2 and 3,

up to 253 V may be applied.

Attention: Jacks (2) and (3) are short-circuited

during all measurements at the test socket!

(Exception: see chapter 12.2)

Standard equipment

Test instrument with 10 + 2 connectors for application parts

1 Probe cable with test probe

1 Clip-on alligator clip for test probes

3 Clip-on quick-clamp terminals

10 conductor patient connection cable 2 mm

10 Clip-on alligator clip 2 mm

1 Calibration certificate per DAkkS

1 Operating instructions

1Carrying strap

Up-to-date PC software (free start-up programs or

demo software for data management, report and list

generation) is available on our website for download.

These operating instructions describe an

instrument with firmware version 7.35.

RS232

IOIOI

max. 10 V

max. 253 V

GMC-I Messtechnik GmbH 3

1 Jack for protective conductor at device under test

2 Jack for neutral conductor at device under test

3 Jack for phase conductor at device under test

4 Jack for connecting the probe

5 Jack for connecting the probe

6 Function selector switch

– Function Test: Function test

– Auto: Automatic test sequence according to selected standard

– PE: Protective conductor test

– Iso/HV: Insulation test / high-voltage test

– I leakage: Leakage current measurement

– V Ω: Multimeter functions

– Aux: Auxiliary multimeter functions

– Setup: Device configuration

7 scroll key for menu and parameter selection

8 scroll key for menu and parameter selection

9 LCD window

10 Socket connector interface RS232 for (P)SI module SECUTEST PSI/SI+, storage

adapter

SECUSTORE

, barcode or RFID scanner

11 Signal lamp for mains connection error

12 key for entry and for starting test sequences and finger contact

13 help key (context sensitive)

14 Key next to the symbol for switching test voltage to

the test socket (only possible if symbol LED is blinking)

15 Signal lamp for the functions test

16 Functional earth (equipotential bonding)

17 Operational earth

18 Connector jacks for application parts

19 Push-buttons (left and right) for releasing the handle from its snap-in position

20 Earthing contact socket for service purposes (Feature B01),

e.g. for connecting a notebook or an A4 format printer, Terminal Data see page 63

21 Standard outlet socket (test socket) for connecting the device under test

22 Push-buttons (left and right) for releasing the lid

23 Lid

24 Compartment for probe and accessories

25 Cover or (P)SI module (accessory

SECUTEST PSI

or SECUTEST SI+)

26 Carrying handle and tilt stand

27 Test probe (accessory probe with coil-cable SK2W (Z745N))

Overview of Available Probe Types

1) Accessory

Note

when using other probes than those specified above

The cables plugged into the sockets (4 and 5) must be short

circuited for testing with the probe, i.e. by plugging the ends of

the cable together, or via a conductive surface at the device

under test (4-wire measurement).

Remove any corrosion from the device under test.

Data Security

Measurement data, report data and user entries are stored to RAM at the

(P)SI module (accessory), as long as the respective battery supplies the

required amount of voltage.

Save your data to a PC on a regular basis in order to prevent any loss of data

at the (P)SI module. We assume no liability for data loss. We recommend the

following PC programs for data processing and data management:

•PS3 (transmission of measurement data to a PC, documentation,

management, report generating and deadline follow-up)

•PC.doc-WORD/EXCEL (report and list generation

•PC.doc-ACCESS (test data management)

•ELEKTROmanager/PROTOKOLLmanager for SECUTEST...

•patManager (Report and list generation)

Probe Type Application Special Features

Standard probe (test probe with

coil-cable and alligator clip)

Max. test current: 25 A Probe with cable

(no coil-cable)

SK2 1) Max. test current: 25 A Probe with cable (no coil-cable),

2 meters long

SK2W 1) Max. test current: 25 A Probe with cable (coil-cable),

2 meters long

Feature KD01 with probe SK5 Restriction with

Feature G01 (IK>25A):

short-circuit current < 25 A

Special probe in combination with

“automatic recognition of measur-

ing point change” function (see

chapter 17)

Brush probe 1)

Can be plugged onto all above

listed probes and test probes

Leakage current,

protective conductor resistance

For contacting devices under test

with rotating, vibrating, exposed

conductive parts

Specyfikacje produktu

Marka:	Gossen Metrawatt
Kategoria:	Przyrządy pomiarowe
Model:	SECULIFE ST HV

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Gossen Metrawatt SECULIFE ST HV, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Przyrządy pomiarowe Gossen Metrawatt

Gossen Metrawatt SECUSTAR FM plus Instrukcja

26 Września 2024

Gossen Metrawatt METRATESTER 4 Instrukcja

26 Września 2024

Gossen Metrawatt METRATESTER 5 Instrukcja

26 Września 2024

Gossen Metrawatt SECULIFE IT Instrukcja

25 Września 2024

Gossen Metrawatt METRAHIT T-COM Instrukcja

25 Września 2024

Gossen Metrawatt METRAHIT 18S Instrukcja

25 Września 2024

Gossen Metrawatt METRISO PRIME Instrukcja

25 Września 2024

Gossen Metrawatt SECUTEST 0701 Instrukcja

25 Września 2024

Gossen Metrawatt SECULIFE ST HV Instrukcja

25 Września 2024

Gossen Metrawatt SECULIFE HIT Instrukcja

25 Września 2024

Instrukcje Przyrządy pomiarowe

Najnowsze instrukcje dla Przyrządy pomiarowe

Voltcraft VC840 Instrukcja

28 Września 2024

Voltcraft VC-12A Instrukcja

28 Września 2024

Voltcraft 122953 - Colour Analysis Instrukcja

28 Września 2024

Voltcraft VC960 Instrukcja

28 Września 2024

Voltcraft VC-531 stroomtang Instrukcja

28 Września 2024

Voltcraft VC-12 Instrukcja

28 Września 2024

Voltcraft VC-10 Instrukcja

28 Września 2024

Voltcraft VC100 serie Instrukcja

28 Września 2024

Voltcraft VC-521 Instrukcja

28 Września 2024

Voltcraft VC950 Instrukcja

28 Września 2024