Instrukcja obsługi Godox LED126
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Godox LED126 (4 stron) w kategorii Błysk. Ta instrukcja była pomocna dla 10 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/4
L
L
L
LLE
E
E
EED V
D V
D V
D VD V
i
i
i
iid
d
d
dde
e
e
eeo L
o L
o L
o Lo L
i
i
i
iig
g
g
ggh
h
h
hht
t
t
tt
型号: LED126/LED170
Instruction manual | 说明手册
Chinese English Bilingual | 中英文双语
705-LED170-07
地址/Add: 深圳市宝安区福永镇福洲大道西新和村华发工业园A4栋
Building A4, Xinhe Huafa Industrial Zone, Fuzhou RD West, Fuyong
Town, Baoan District, Shenzhen 518103, China
电话/Tel: +86-755-29609320(8062) Fax: +86-755-25723423传真/
邮箱/E-mail: godox@godox.com
深圳市神牛摄影器材有限公司
GODOX Photo Equipment Co., Ltd.
5.滤色片更换
● 用手轻轻按住滤色片(02)向右推。
● 听到“咔”声后，抽出滤色片(02)。
● 将新滤色片直接插入，向左推移，听到“咔”声
后表示锁紧，更换完毕。
* 设计和规格如有变更，恕不另行通知。
产品型号
灯珠数量
电池供电
DC电源供电
功率
亮度
锂电池供电
色温
调光方式
使用时长(以碱性电池为参考)
色片
工作环境温度
产品尺寸(不包含转轴尺寸)
净重
五、产品参数
LED126
126个
6*AA电池
6~9V
<7.5W
>2 00Lux (0.5 米)2
SONY：NP-F970（数码摄像机/相机充电电池）
5500~6500K
无级调光
约1小时
柔光片、黄色滤色片各1张
-10~55度
143*96.5*42.5mm
280g
LED170
170个
8*AA电池
6~12V
<10W
>2700Lux (0.5 米)
172*108.6*42.5mm
350g
Thank you for purchasing this Godox Product!
This LED video light is excellent for macrophotography, product shooting,
photojournalistic and video recording, etc. This lightweight and portable
light provides high brightness and accurate color temperature. It comes
with a diffusion filter and a yellow filter, and also supports multiple power
supply modes. You can flexibly control the light brightness by using the
dimmer and change the illumination direction by using the angle adjusting
knobs.
Foreword:
Always keep this product dry. Do not use in rain or in damp conditions.
Do not disassemble. Should repairs become necessary, this product
must be sent to an authorized maintenance center.
Keep out of reach of children.
As this product do not have waterproof function, please take measures
of waterproof in rainy or damp environment.
Do not use or store the product if the ambient temperature reads over
50°C.
Do not use the flash unit in the presence of flammable gases,
chemicals and other similar materials. In certain circumstance, these
materials may be sensitive to the strong light emitting from this flash
unit and fire or electromagnetic interference may result.
Observe precautions when handling batteries
● Do not put batteries into a fire or apply direct heat to them.
● Batteries are prone to leakage when fully discharged. To avoid
damage to the product, be sure to remove batteries when the
product is not used for a long time or when batteries run out of
charge.
● Should liquid from the batteries come into contact with skin or
clothing, rinse immediately with fresh water.
Warning:
01. LED Beads
02. Color Filters
03. Power Switch
04. Brightness Controller
05. Battery Level Indicator
06. DC Power Jack
07. Battery Compartment Lock
08. Battery Compartment
09. Lithium Battery Container
10. Angle Adjusting Knob A
11. Angle Adjusting Knob B
12. Locking Ring
13. Camera Hotshoe Connection
14. 1/4″ Bracket Mounting Hole
Parts:
01
03
02
04
05
06
07
14
10
11
12
13
09
08
1.Power Supply
Three power supply modes are available:
2.Installing the Video Light
● Screw the Locking Ring (12) to the highest point
and insert the Camera Hotshoe Connection (13)
horizontally into the hotshoe of a camera or a
camcorder.
● Tighten the Locking Ring (12).
Note: If your camcorder has no hotshoe connection, you
are advised to purchase a connecting bracket for
camcorder. The video light has a 1/4″ Bracket Mounting
Hole as your camcorder does. Therefore, you can easily
connect both the light and the camcorder to the bracket.
* When using AA batteries or lithium battery, the Battery Level
Indicator (05) turns green, meaning battery power is sufficient.
When the indicator turns red, the battery power is low.
* When the indicator turns red and blinks, the lithium battery
power is low. Please recharge it immediately before use in
order to avoid forceful auto off.
* When using DC power supply, the indicator shows green.
●
Using batteries: This
light uses AA-sized
alkaline or Ni-MH
rechargeable batteries.
●
Using lithium battery:
This light uses SONY
NP-F970 model lithium
battery.
●
Using DC power jack:
This light can be powered
by DC power supply. Use
an adapter (purchased
separately) to connect the
light with the AC power
supply. LED126 uses a
6V-9V adapter and
LED170 uses a 6-12V
adapter.
Installation and Operation
Specyfikacje produktu
| Marka: | Godox |
| Kategoria: | Błysk |
| Model: | LED126 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Godox LED126, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Błysk Godox
9 Stycznia 2025
9 Stycznia 2025
9 Stycznia 2025
9 Stycznia 2025
7 Stycznia 2025
7 Grudnia 2024
9 Października 2024
8 Października 2024
7 Października 2024
7 Października 2024
Instrukcje Błysk
- Błysk Sony
- Błysk Leica
- Błysk Panasonic
- Błysk Canon
- Błysk Asus
- Błysk Fujifilm
- Błysk Sigma
- Błysk Nikon
- Błysk Minox
- Błysk LogiLink
- Błysk Vimar
- Błysk Ricoh
- Błysk Rollei
- Błysk Lastolite
- Błysk Olympus
- Błysk Pulsar
- Błysk Audio-Technica
- Błysk Konica Minolta
- Błysk COLBOR
- Błysk GVM
- Błysk Pentax
- Błysk Quantum
- Błysk EasyMaxx
- Błysk Ikan
- Błysk Impact
- Błysk Aputure
- Błysk Dörr
- Błysk Metz
- Błysk Bolt
- Błysk Nissin
- Błysk Profoto
- Błysk Hähnel
- Błysk Vello
- Błysk Goodram
- Błysk Yongnuo
- Błysk Konig
- Błysk Xit
- Błysk Genaray
- Błysk Sunpak
- Błysk SeaLife
- Błysk Neewer
- Błysk Xantech
- Błysk Kenko
- Błysk Elinchrom
- Błysk Dracast
- Błysk Cullmann
- Błysk Rotolight
- Błysk Cactus
- Błysk PolarPro
- Błysk ANDYCINE
- Błysk Westcott
- Błysk Ikelite
- Błysk Kaiser Fototechnik
- Błysk Triopo
- Błysk Luxli
Najnowsze instrukcje dla Błysk
8 Stycznia 2025
27 Grudnia 2024
22 Grudnia 2024
22 Grudnia 2024
22 Grudnia 2024
15 Grudnia 2024
15 Grudnia 2024
15 Grudnia 2024
14 Grudnia 2024
14 Grudnia 2024