Instrukcja obsługi Gigaset AS300A Duo

Gigaset telefon AS300A Duo

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Gigaset AS300A Duo (4 stron) w kategorii telefon. Ta instrukcja była pomocna dla 10 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

Gigaset AS200-AS200A-AS300_AS300A_UK _ A31008-M2208-L101-2-7619

Quick start guide

AS200 - AS200 A

AS300 - AS300 A

GIGASET. INSPIRING CONVERSATION.

GIGASET HELPLINE: 0845 3670812

Pack contents

If you have purchased a model

with multiple handsets the

package should contain two

batteries, a battery cover, a

charging cradle 8 with mains

adapter 9 for each additional

handset.

1one Gigaset AS200/AS200A/AS300/AS300A Base station

2one mains adapter

3one Gigaset AS200H/AS300H handset

4one phone cord

5two batteries

AS185

GIGAS ET . INS PIRING C ONVERSA T ION.

6one battery cover

7this Quick start guide

8 9

Connecting the base station

¤Connect power adapter 1 and

Phone jack 2 to the base and

place the cable recesses.

Please ensure the power lead is

fully inserted.

Please note:

uThe mains adapter must always be connected, as the Phone will not operate

without a mains connection.

uAlways use the power adapter and Phone cord supplied. Pin connections on

Telephone cables can vary.

Connecting the charging cradle (if included)

¤Plug the mains adapter into the

plug socket 2.

¤Connect the flat plug from the

mains adapter 1.

If you need to disconnect the plug from the

charging cradle, press the release button 3 and

disconnect the plug 4.

Preparing the handset

Initial charging and discharging of the batteries

Insert the batteries the right way

round. The polarity is indicated

in/on the battery compartment.

¤Then slide the battery cover back

into the main casing until it clicks

into place.

If you need to open the battery cover, for

instance to replace the batteries, place

your fingertip in the grooved area on the

top of the cover and slide down.

The correct charge status can only be displayed if

the batteries are first fully charged and discharged.

¤Place the handset in the charger

for 7hours.

Then remove the handset from the charger, make and receive Phone calls, setup the

Phone etc. and do not put it on the charger until the batteries are fully discharged.

Setting the date and time

Set the date and time so that the correct date and time can be assigned to incoming

calls, and so that the alarm can be used.

Date: DD: MM: YY

“ T OK

INT MENU

¤Press the key below MENU on the

display screen to open the main

menu.

Date/Time

“OK

¤Press the bottom of the control

key ...

... until the Settings menu item

appears.

¤Press the key below OK on the

display screen to confirm your

selection.

The Date/Time menu item appears on

the display.

¤Press the key below OK on the

display screen to open the input

field.

Settings

“OK

¤The active cursor position is flashing.

Enter day, month and year as an

6-digit number via the handset,

e.g. Q11Q1Q for 01/10/10.

Message indication

Message Indication Key ‘ on handset will flash to indicate one or all of the

following events:

umissed calls (if caller ID is enabled for your line numbers will be shown)

unew messages on the answer machine (AS200A/AS300A only)

Activating/deactivating the answer machine (AS200A/AS300A only)

MENU ¢Voice Mail ¢OK ¢Answer Mach. ¢OK (‰= on)

If the answer machine is activated, the answer machine icon ± will be displayed in

the header.

To retrieve your messages, just press the flashing ‘ key on your handset.

Dial tone

The dial tone will only be heard when pressing the c call button for 2 seconds.

A short press will open the redial list.

You can also use the

speaker button (AS300/AS300A only).

Display in idle status

u2: internal number, if more then one handset is registered

u±: answer machine is activated (AS200A/AS300A only)

uBattery charge status:

–= e V U (empty to full)

–= flashes: batteries almost empty

–e V U flashes: charging procedure

Registration handset

Your handsets should already be registered by default, if your handset is flashing the

text "No Base" then it can be that:

uYour base station is not switched on, please check if the power supply is connected

properly.

uThere is too much distance between the handset and base.

uYour handset has not been pre-registered in the factory.

In the case that the handset has not been pre-registered, or you want to register an

additional handset to your base station, use the manual registration procedure

below.

Automatic registering procedure

Manual registration procedure

1. On the handset:

MENU ¢Settings ¢OK ¢Handset ¢OK ¢Register HS ¢OK ¢enter the

system PIN for the base and press OK. Default PIN = 0000

2. On the base station:

Within 60 seconds of entering the system PIN, press and hold the registration/paging

key (min. 3 seconds). Registration takes approx. 1 minute.

You can register up to four handsets to your base. You can also register other Gigaset

handsets and handsets from other devices with GAP functionality.

Put into base

Place the handset with the

display facing up in the base

station.

The handset registers

automatically. Registration

can take up to 5 minutes.

Do not remove the handset

from the base station during

this time.

Put into base

Registering

Frequently asked questions

Q: There is no dial tone.

A: Press call button for 2 seconds (long press) to obtain dial tone.

A short press opens the redial list.

Q: The line is crackling / not clear.

A: Have you used the new line cable provided? Please do not use an old cable.

Q: The display is not clear / seems to be broken.

A: The display is protected by a plastic film, please make sure you have removed

the protective film.

Q: The handset is not registered.

A: If your handset is not registered, please follow the Registration handset procedure.

(Described on this page)

Q: The caller ID is not working.

A: Have you subscribed to this service (CLIP) from your provider?

Q: Message indicator flashing and I cannot retrieve my message.

A: Message indicator will flash to indicate missed calls. (Described on this page)

Please check:

Have you used the phone cord supplied 

Have you fully inserted the power cable into the base station 

Have you inserted the batteries correctly 

Have you charged the batteries for 7 hours 

Have you set up the Date/Time 

To download the latest manuals, visit our web-site: http://www.gigaset.com

You have questions? As a Gigaset customer, you can take advantage of our comprehensive

service offerings. You can find help quickly in this User Manual and in the service pages of

our Gigaset online portal: http://www.gigaset.com

Product may not be fully compatible with the national telephone network. It is clearly

specified on the box near the CE mark for which country/countries the equipment has been

developed. If the equipment is used in a manner inconsistent with this advice or with the

instructions of the manual and on the product itself, this may have implications on the

conditions for warranty or guarantee claims (repair or exchange of product).

In order to make use of the warranty, the product purchaser is asked to submit a receipt

which proves the date of purchase (date from which the warranty period starts) and the

type of goods that have been purchased.

If you have problems setting up or operation this product please call

GIGASET UK HELPLINE 0845 3670812

GIGASET IRL HELPLINE 1850 777277

Gigaset AS200-AS200A-AS300_AS300A_UK _ A31008-M2208-L101-2-7619

The handset and base at a glance

± V

11.12. 11:56

INT MENU

The base station at a glance

The handset at a glance

1Registration/paging key:

Search for handsets (press briefly, "Paging" )

2On/Off key: activate and deactivate answer machine.

Lights up: answer machine is activated.

Flashes: there is at least one new message or message is

in the process of being recorded.

Flashes very quickly for about 4 seconds: memory is full.

3Volume keys: (– + = quieter; = louder)

During message playback: adjust the speaking volume.

While phone is ringing: adjust ringer volume.

4Play/Stop key:

Play back messages from the answer machine, or cancel

playback.

During message playback:

5Delete current message.

6Skip to the start of the current message (press once) or go

to the previous message (press twice).

7Skip to next message.

Display keys on handset:

Pressing a key launches the func-

tion that appears above that key

in the display.

AS200/AS200AAS300/AS300A

Display

icon

Function when

pressed

INT Call other registered

handsets.

MENU Open main/submenu.

“ Go back one menu

level.

UScroll up/down or

adjust volume with u.

T Move cursor to left/

right with u.

˜Backspace deletes one

character at a time

from right to left.

OK Confirm menu

function or save entry.

1 Charge status of the batteries

2 Answer machine icon

(AS200A/AS300A only)

3 Display keys

4 Message key

Flashes: new messages re-

ceived

5AS200/AS200A:

h Directory key

AS300/AS300A:

d Handsfree key

6 Control key (u)

7 Talk key

8 AS300/AS300A:

h Directory key

(press down)

9 End call and

On/Off key

10 Ringer on/off

(press and hold

in idle status)

11 Keypad lock on/off

(press and hold)

12 Recall key

- Consultation call

(flash)

- Dialling pause

(press and hold)

13 Microphone

14 "Microphone off " key

Making calls

Making external calls and ending

calls

External calls are calls using the public telephone

network.

~ (Enter the phone number) ¢c.

The phone number is dialled. (Or you can first

press and hold c [dial tone] and then enter the

number.) During the call you can adjust the ear-

piece volume using

t and set the volume with u.

End the call/cancel dialling:

Press the end call key a.

You can automatically insert a network provider

dialling code before any phone number.

Accepting a call

The handset indicates an incoming call by ringing

and by a display on the screen. Press the talk key

c to accept the call. When Auto Answer is acti-

vated, simply remove the handset from the base

station/charging cradle. In idle status, use t to

activate the menu for setting the call volume and

use u to set the volume.

Calling Line Identification

When you receive a call, the caller's number will be

displayed on your handset; the caller's name will

be displayed if it is stored in the directory.

Requirements:

1You have asked your network provider for the

caller's number (CLIP) to be displayed on your

handset screen.

2The caller has asked the network provider for his

number to be identified (CLI).

® appears in the display if you have

not requested Calling Line Identification,

Withheld appears if the caller has withheld CLI,

and Unavailable appears if CLI has not been

requested.

Switch to mute

You can mute your handset when making

external calls. Your caller can no longer hear you.

Press the "Microphone off" key

m during the call

to activate/deactivate the function.

Using the directory and lists

Using shortcut keys

You can assign directory entries to the keys 0

and 2–9:

h u ¢(select entry)

¢MENU ¢Shortcut ¢OK

¢~(press the key you want to assign the

entry to)

To dial, press and hold the required shortcut key.

Transferring the directory to

another handset

Requirements:

uThe sending and receiving handsets must

both be registered to the same base station.

uThe other handset and the base station can

send and receive directory entries.

h u ¢(select entry) ¢MENU

¢Send Entry / Send List ¢OK

¢~(enter the internal number of the

receiving handset) ¢OK

Last number redial list

This list contains the ten last dialled numbers.

Dialling from the last number redial list

c (press briefly)

¢u (select entry)

¢c

Managing entries in the last number

redial list

c (press briefly)

¢u (select entry)

¢MENU

You can select the following settings:

Calls list/voicemail (network

mailbox) list

An advisory tone sounds and the message key

flashes as soon as a new entry appears in the calls

list/voicemail list. A message appears in the

display.

When you press the f key, all the lists are dis-

played. If only one list contains new messages,

this will be opened automatically.

Calls list

Precondition: CLIP

Depending on the type of list set, the calls list

contains

uanswered calls

umissed calls

ucalls on the answer machine (AS200A/AS300A)

Depending on the type of list set, all numbers of

the last 25 incoming calls are saved or just the

missed calls are saved.

The calls list is displayed as follows:

Number of new entries + number of old, read entries

Open the calls list

f ¢CallsList 01+02 ¢OK

The last incoming call is displayed.

If necessary, use u to select another entry.

Using other functions

u(select entry) ¢MENU

The following functions can be selected with u:

Calling back a caller from the calls list

f ¢CallsList 01+02 ¢OK

¢u(select entry) ¢c

Use Number Edit or add to the number.

Then dial or select other

functions from the MENU.

Copy to Dir. Copy an entry to the directory.

Delete Entry Delete selected entry.

Delete List Delete all entries.

Please note:

If calls are saved in the network mailbox, you will

receive a message if the appropriate settings

have been set (depending on your network

provider).

Delete Entry Delete current entry.

Copy to Dir. Copy an entry to the directory.

Date/Time Call date and time (if set).

Status New Call: new missed call.

Old Call: entry already read.

Answ.: call taken.

Delete List Warning! All old and new

entries will be deleted.

CallsList 01+02

Answer machine (AS200A/AS300A)

The answer machine can be operated from the

handset or by using the key on the base station.

The telephone is supplied with a pre-recorded

announcement. You can only record your own

announcement messages using the handset.

This pre-recorded announcement is used if no

personal announcement is available.

If the memory is full, the answer machine switches

itself off automatically. It activates again automat-

ically when you delete old messages.

Activating/deactivating the answer machine

MENU ¢Voice Mail ¢ ¢OK Answer Mach.

¢OK (‰= on)

When the answer machine is switched on,

the ± icon appears in the display.

Recording your own announcement

MENU ¢Voice Mail ¢ ¢OK Announcements

¢OK ¢Rec announce ¢OK

¢Speak after OK ¢OK

You hear the ready tone (short tone). Now say

your announcement (at least 3 seconds).

Press OK to confirm or press

a ” or to reject your

recording. After recording, the announcement is

played back for you to check.

Please note:

Recording ends automatically when the max.

recording time of 170 seconds is reached or if

there is a break in speaking of more than

2 seconds.

Playing/deleting messages

Open the voicemail list to play back messages.

Stopping and controlling playback

During message playback:

Deleting individual messages

While playback is paused, press the

display key.

Deleting all old messages

During playback or pause:

MENU ¢Delete all old

¢OK (confirm the security prompt)

Accepting call from answer machine

You can still accept a call while the answer

machine is recording the message by pressing c.

Recording stops and you can speak to the caller.

Setting up the answer machine

The answer machine has already been preset at

the factory. Make individual settings using the

handset.

Details on how to set a delay time, after which the

answer machine is to answer a call, as well as

details on how to set the recording length and

activate call screening during the recording, are

available from the Menu tree.

Assigning key 1 for fast access to the answer

machine (network mailbox)

Simply press and hold key 1 on the handset and

you will be connected directly to the answer

machine (network mailbox).

Remote operation when on the move

You can check and activate your answer machine

from any other telephone (hotel, pay phone etc.).

Requirements:

uYou have set a system PIN other than 0000.

uThe phone you are using for remote

operation has touch tone dialling (DTMF),

i.e. you hear different tones when you press

the keys.

Calling the answer machine and playing

back messages

~ (Dial your own number) ¢while listening to

your announcement: press the 9key and enter

the system PIN

The following keys are used for operation:

Activating the answer machine

~ (Enter your own number and allow the phone

to ring until you hear the message: "Please enter

PIN") ¢~ enter system PIN

2Stop playback. Press 2 again to resume.

tGo to the start of the current message.

2 x tSkip to the previous message.

vSkip to the next message.

2 x vGo to the next message but one.

AGo to the start of the current message.

Press twice to go back to the previous

message.

BStop playback. Press again to resume.

3Skip to next message.

0delete current message.

Phone settings

Changing the display language

MENU ¢Settings ¢OK

¢Handset ¢OK

¢Language ¢OK

¢select the language ¢OK

The current language is indicated by ‰.

If you accidentally choose a language you do not

understand:

MENU ¢421

(press the keys one after the other)

Select the correct language with

u and press .OK

Resetting the handset

You can reset individual settings and changes that

you have made. Entries in the directory, the calls

list and the handset's registration to the base

station will be retained.

MENU ¢Settings ¢OK

¢Handset ¢OK

¢Reset Handset ¢OK

Cancel the reset with

Restoring the base station to the

factory settings

When restoring factory settings:

uAll handsets are de-registered

uIndividual settings are reset

uAll lists are deleted

uThe system PIN is reset to the original

code 0000

Only the date and time are retained.

Software reset

MENU ¢Settings ¢OK

¢Base ¢OK

¢Base Reset ¢OK

Hardware reset

Disconnect the power cord from the base station.

Hold down the registration/paging key on the

base station while reconnecting the power cable

to the base station. Release the key after approxi-

mately 5 seconds.

Repeater mode

With a repeater you can increase the range of your

base station. You will need to activate repeater

mode. Repeater mode and Eco mode or Eco

mode+ cancel each other out.

Operating the base station on

the PABX

The following settings are only necessary if

your PABX requires them, see the user guide

for your PABX.

When entering the digits, enter them slowly

one after the other.

Changing the dialling mode

MENU ¢4 I O 1 1

¢The number for the set dialling mode flashes:

0 = touch tone dialling (DTMF);

1 = dial pulsing (DP)

¢enter number ¢OK.

Setting recall

MENU¢4IO12

¢The number for the current recall flashes:

0 = 80 ms; 1= 100 ms; 2= 120 ms; 3= 400 ms;

4 5 = 250 ms; = 300 ms; 6 = 600 ms; 7 = 800 ms

¢ ¢enter number OK.

Changing pause after line seizure

You can set the length of the pause inserted

between pressing the talk key c and sending the

phone number.

MENU ¢4 I O 1 O

¢The number for the current pause length

flashes: 1 = 1 sec.; 2= 3 sec.; 3 = 7 sec.

¢enter number ¢OK.

Changing the pause after the recall key

MENU ¢4 I O 1 4

¢The number for the current pause length

flashes: 1 = 800 ms; 2 3 = 1600 ms; = 3200 ms

¢enter number ¢OK.

Locating a handset ("paging")

You can locate your handset using the base

station.

uBriefly press the registration/paging key on

the base station.

uAll handsets will ring simultaneously

("paging"), even if the ringer tones are

deactivated.

End paging: briefly press the registration/paging

key on the base station or the talk key c on a

handset.

General

Using several handsets

Making internal calls

Internal calls are free calls to other handsets that

are registered to the same base station.

To make a call to other handsets, press

uINT ¢~ (1...4, enter internal number of

the handset), the handset is called or

uINT ¢star key P, all handsets are called.

When a participant answers you can speak to

them. To end the call, press the end call key

Internal consultation call/

connecting a call

You are in conversation with an external

participant. Press the INT key and call one or all

handsets. The external participant hears the hold

music.

uBefore the internal participant has answered,

press the end call key a; the call is diverted

to the participant who answers the call.

uAfter the internal participant has answered,

you can talk to him. Press the end call key a;

the call is diverted, or press the display key

”;

you are reconnected to the external partici-

pant.

Listening in to an external call

You are conducting an external call. An internal

participant can listen in on this call and take part

in the conversation (conference).

Precondition: The Listening in function must be

activated.

Activating/deactivating listening in

MENU ¢Settings ¢OK ¢Base ¢OK

¢Listening in ¢OK (‰= on)

Internal listening in (conference)

You want to listen in to an existing external call.

Press and hold the c key. You can listen in to the

call. All participants hear a signal tone.

To end: press the end call key a. All participants

hear a signal tone.

If the first internal participant presses the end call

key a, the handset that has "listened in" remains

connected to the external participant.

Setting the alarm clock

Activating/deactivating the alarm clock

MENU ¢ Alarm Clock ¢OK

¢ Activation ¢OK (‰ = on)

When activated:

¢Set the wake-up time ¢OK

When the alarm clock rings, press any key to

switch it off for 24 hours.

If the alarm clock is set, the wake-up icon l will

appear on the screen and the wake-up time will

be displayed instead of the date.

Setting the wake-up time

MENU ¢Alarm Clock ¢OK

¢Wake-up time ¢OK

Enter the wake-up time in hours and minutes,

then press OK.

Entering letters/characters

Press the relevant key the number of times

indicated.

Briefly press the hash key # to switch from

"Abc" to "123" mode, from "123" to "abc" mode

and from "abc" to "Abc" mode.

Standard characters

1) Space

123456789

10 11 12 13 14

1 1 £ $ ¥ ¤

2 a b c 2 ä á à â ã ç

3 d e f 3 ë é è ê

4 g h i 4 ï í ì î

5 j k l 5

6 m n o 6 ö ñ ó ò ô õ

7 p q r s 7 ß

8 t u v 8 ü ú ù û

9 w x y z 9 ÿ ý æ ø å

0 . , ? ! 0 + - : ¿ ¡ " ’ ; _

P* / ( ) < = > %

Abc

-->

123

-->

abc # @ \ & §

Safety

Safety precautions

uOnly use the mains adapter supplied.

uFit only the recommended, rechargeable

batteries, i.e. never use any other battery type

or non-rechargeable batteries as this could

result in significant health risks and personal

injury.

uThe operation of medical appliances may be

affected. Be aware of the technical conditions

in your particular environment, e.g. doctor's

surgery.

uDo not hold the rear of the handset to your

ear when it is ringing. Otherwise you risk

serious and permanent damage to your

hearing.

The handset may cause an unpleasant

humming noise in hearing aids.

uDo not install the phone in a bathroom or

shower room. The handset and base station

are not splashproof.

uDo not use your phone in environments with

a potential explosion hazard, e.g. paint shops.

uIf you give your Gigaset to someone else,

make sure you also give them the user guide.

uPlease remove faulty base stations from use

or have them repaired by Service, as they

could interfere with other wireless services.

uDisposal:

Batteries should not be disposed of in general

household waste. Observe the local waste

disposal regulations, details of which can be

obtained from your local authority or the

dealer you purchased the product from.

All electrical and electronic equipment must

be disposed of separately from general

household waste using the sites designated

by local authorities. If a product displays this

symbol of a crossed-out rubbish bin, the

product is subject to European Directive

2002/96/EC. The appropriate disposal and

separate collection of used equipment serve

to prevent potential harm to the environment

and to health. They are a precondition for the

re-use and recycling of used electrical and

electronic equipment.

For further information on disposing of your

used equipment, please contact your local

authority, your refuse collection service or the

dealer you purchased the product from.

Emergency numbers cannot be dialled if the

keypad lock is activated!

Not all of the functions described in this user

guide are available in all countries.

Care

Wipe down the base station and handset with a

damp cloth (no solvents) or an antistatic cloth.

Never use a dry cloth. This can cause static.

Contact with liquid

If the handset should come into contact with

liquid:

uSwitch the handset off and remove the

batteries immediately.

uAllow the liquid to drain from the handset.

uPat all parts dry, then place the handset with

the battery compartment open and the

keypad facing down in a dry, warm place

for at least 72 hours (not in a microwave,

oven etc.).

uDo not switch on the handset again until it

is completely dry.

When it has fully dried out, you will normally be

able to use it again.

Read this user guide and the safety precautions

carefully before use. Explain their content and the

potential hazards associated with using the

telephone to your children.

ECO DECT

You are helping to protect the environment with

your Gigaset AS200/AS200A/AS300/AS300A.

Reduced energy consumption

Your telephone has a power-saving adapter plug

and uses less power.

Reduced transmission power

The transmission power of your telephone is

reduced automatically:

The handset's transmission power is reduced

depending on the distance to the base station.

The transmission power on the base station is

reduced to virtually zero when only one handset

is registered and the handset is in the base

station.

You can reduce the transmission power of the

handset and base station even more by using

Eco Mode/Eco Mode+:

uEco Mode: 80% transmission pow

er reduction in standby mode and during a

call (the range of the base station is

reduced).

uEco Mode+: 100% transmission power deac-

tivation in standby mode (top left display

icon ½ c). Press and hold the talk key to

check that the base station can be reached.

You will hear the ringing tone if the base sta-

tion can be reached.

Registering handsets that do not support

Eco Mode+ causes the mode to be deacti-

vated on the base and all other handsets.

Specifications

Recommended batteries

Technology: Nickel-metal-hydride (NiMH)

Size: AAA (Micro, HR03)

Voltage: 1.2 V

Capacity: 400–800 mAh

We recommend the following types of battery:

GP 550/700 mAh, Yuasa Phone 700/800 mAh,

Peacebay 550/650 mAh ( Valid at the time of going

to press). The handset is supplied with recom-

mended batteries.

Base station power consumption

General specifications

Guarantee Certificate United Kingdom

Without prejudice to any claim the user (customer)

may have in relation to the dealer or retailer, the cus-

tomer shall be granted a manufacturer's Guarantee

under the conditions set out below:

uIn the case of new devices and their components

exhibiting defects resulting from manufacturing

and/or material faults within 24 months of pur-

chase, Gigaset Communications shall, at its own

option and free of charge, either replace the device

with another device reflecting the current state of

the art, or repair the said device. In respect of parts

subject to wear and tear (including but not limited

to, batteries, keypads, casing), this warranty shall

be valid for six months from the date of purchase.

uThis Guarantee shall be invalid if the device defect

is attributable to improper treatment and/or fail-

ure to comply with information contained in the

user guides.

uThis Guarantee shall not apply to or extend to serv-

ices performed by the authorised dealer or the

customer themselves (e. g. installation, configura-

tion, software downloads). User guides and any

software supplied on a separate data medium shall

be excluded from the Guarantee.

uThe purchase receipt, together with the date of

purchase, shall be required as evidence for invok-

ing the Guarantee. Claims under the Guarantee

must be submitted within two months of the Guar-

antee default becoming evident.

uOwnership of devices or components replaced by

and returned to Gigaset Communications shall

vest in Gigaset Communications.

uThis Guarantee shall apply to new devices pur-

chased in the European Union. For Products sold in

the United Kingdom the Guarantee is issued by:

Gigaset Communications UK Limited, Quatro

House, Lyon Way, Camberley, Surrey, GU16 7ER.

uAny other claims resulting out of or in connection

with the device shall be excluded from this Guar-

antee. Nothing in this Guarantee shall attempt to

limit or exclude a Customers Statutory Rights, nor

the manufacturer's liability for death or personal

injury resulting from its negligence.

uThe duration of the Guarantee shall not be

extended by services rendered under the terms of

the Guarantee.

uInsofar as no Guarantee default exists, Gigaset

Communications reserves the right to charge the

customer for replacement or repair.

uThe above provisions does not imply a change in

the burden of proof to the detriment of the cus-

tomer.

To invoke this Guarantee, please contact the Gigaset

Communications telephone service. The relevant

number is to be found in the accompanying user

guide.

Authorisation

This device is intended for analogue phone lines

in the UK. Country-specific requirements have

been taken into consideration.

We, Gigaset Communications GmbH, declare that

this device meets the essential requirements and

other relevant regulations laid down in Directive

1999/5/EC. A copy of the 1999/5/EC Declaration of

Conformity is available at this Internet address:

www.gigaset.com/docs

Issued Gigaset Communications GmbH

Frankenstr. 2a, D-46395 Bocholt.

Rights of modification reserved.

www.gigaset.com

A31008-M2208-L101-2-7619

In standby mode

– Handset in base station

– Handset outside base station

approx. 1.0 W

approx. 0.7 W

During a call approx. 0.8 W

DECT standard is supported

GAP standard is supported

Range up to 300 m outdoors

up to 50 m indoors

Base station power

supply 230 V ~/50 Hz

Environmental condi-

tions in operation +5°C to +45°C, 20% to

75% relative humidity

Using the directory and lists

Specyfikacje produktu

Marka:	Gigaset
Kategoria:	telefon
Model:	AS300A Duo
Kolor produktu:	Czarny
Czas rozmowy:	20 h
Czas gotowości:	220 h
Długość przekątnej ekranu:	1.5 "
Maksymalny zakres zewnętrzny:	300 m
Nazwa i identyfikacja dzwoniącego:	Tak
Rodzaj baterii:	AAA
Model:	Telefon w systemie DECT
Liczba baterii:	2
Kolory wyświetlacza:	Monochromatyczne
Typ mocowania:	Ściana
Maksymalny czas nagrywania:	12 min
Kolor podświetlenia:	Bursztyn
Obsługa funkcji Plug & Play:	Tak
Przyciski oświetlane od tyłu:	Tak
Ilość linii teksu:	3 linii
Montaż naścienny / rzutowanie na sufit:	Tak
Pojemność książki telefonicznej:	60 wejścia
Wskaźnik ładowania baterii:	Tak
Automatyczna sekretarka:	Tak
Liczba melodii:	10
Współpraca z wieloma słuchawkami:	4
Pojemność listy połączeń:	25
Klawisze nawigacyjne:	Tak
Słuchawka:	2
Dzwonek polifoniczny:	Tak
Maksymalny zakres wewnętrzny (pomieszczenie):	50 m
Wymiary słuchawki (SxGxW):	49 x 31 x 147 mm
Wymiary stacji bazowej:	103 x 56 x 124 mm
Zegar z kalendarzem:	Tak