Instrukcja obsługi Geemarc AMPLICALL PSA200

Geemarc Niesklasyfikowane AMPLICALL PSA200

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Geemarc AMPLICALL PSA200 (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

Transmitter

1. Loudspeaker

2. Battery cover

3. Power slide switch

(Alert/o󰀨/arm)

4. Pressure sensor mat

2 3 4

Pressure sensor mat and alarm

DESCRIPTION

INSTALLATION

Inside your gift box you should nd the below elements:

- 1 user guide

- 1 pressure sensor mat and its transmitter

- 1 wireless receiver

- Batteries are not included.

- A mains adapter is available as a spare part (6V 0.3A)..

(Fig1) (Fig 2)

(Fig3)

(Fig 4)

(Fig 5)

FEATURES

AMPLICALL PSA 200

Box Content

Wireless receiver

1. Volume control (HI/LO)

2,4. Visual indicators (Flash when

triggered by transmitter)

3. Visual indicator (Flashes when

triggered by transmitter/ Lights up

when batteries are low)

5. Loudspeaker

8. “Learn” paring button

9. Battery cover

10. Screw

11. Holes to mount device onto a wall

6. Power slide switch (Alarm/

o󰀨/chime)

7. DC adaptor socket (6V

DC/0.3A)

Setting up the transmitter and placing

the pressure sensor mat.

Setting up the receiver

1. Slide open the transmitter’s battery compartment

and place a 9V battery type PP3 (not included) while

observing the correct polarity before replacing the

battery cover. (Fig1)

2. Connect the transmitter’s wire to that of the

pressure sensor pad. (Fig2)

3. Place the pressure sensor mat under the cushion

of the wheelchair of the person you are caring for.

(Fig3)

Note: The transmitter

can be installed

onto a wall. To

do so the bellow

instructions should

be followed.

4. Drill two holes horizontally, 44 mm apart.

5. Insert two wall plugs xing into the two holes.

6. Screw two screws into the plugs, hang the

transmitter on the support and slide it down to lock it.

1. Unscrew the screw that is on the back of the wireless

receiver and that holds the cover of the battery

compartment in place before sliding open the battery

compartment. (Fig4)

2. Place three 1.5V batteries ( type LR14 ) in the battery

compartment while observing the correct polarity, and

place the battery compartment back in place. (Fig5)

3. You can connect an AC adapter 6V DC 0.3A (not

included); plug length: 12mm; inside positive ID: 2.1mm;

outside negative OD: 5.5mm) to the alert, and install the

batteries as backup in case of power failure.

Note: The receiver is wall mountable.

A. Drill two holes horizontally, 36 mm apart.

B. Insert two wall plugs xing into the two holes.

C. Screw two screws into the plugs, hang the receiver on the

support and slide it down to lock it.

The Amplicall PSA200 consist of a battery powered pressure

sensor mat connected to a signal transmitter, and a wireless

signal receiver.

As soon as pressure stops being applied to the sensor mat, the

transmitter it is connected to will send a signal to the wireless

receiver which will immediately start ringing and ashing. The

receiver’s alarm volume can be set to high or low. The distance

between the transmitter and the receiver should not exceed 30

meters in open eld.

The pressure sensor mat, which is powered by a 9V battery

(not included) was designed to be placed on the wheelchair or

mattress of a person with reduced mobility. The alarm it needs to

be paired with, which can work either with batteries (not included)

or plugged into the mains (adaptor not included), alerts the

caregiver whenever the person p1-he or she cared for appears to no

longer be sitting or lying on the pressure sensor mat.

Extremely easy to use our product is suitable for households that

count a member with reduced mobility, nursing homes, hospitals

and other places where patients or residents are being cared for.

Distance in between cannot exceed 30 meters.

EVERYDAY USE

You need to sit on the pressure sensor mat before turning on the

transmitter, otherwise the alarm will start ringing.

When sitting on the pressure sensor mat, move the power slide

switch of the transmitter to the “ ” position. The transmitter will ALERT

sound 4 seconds later to indicate it is now working. As soon as the

transmitter detects that no pressure is being applied to the sensor

mat, it will send a signal to the wireless receiver to trigger its alarm

and ashing light. It will keep sending a signal every 40 seconds

until pressure is once again applied on the sensor mat.

When the power slide switch of the receiver is placed on the

“CHIME” position, the receiver will ring and ash for 5 seconds

every 30 seconds each time it receives a signal from the transmitter

alerting it that no pressure is being applied on the sensor mat. The

receiver will keep ringing until it is turned o󰀨 or pressure is once

again applied on the sensor mat.

When the power slide switch of the receiver is placed on

the “ALARM” position, the receiver will ring and ash for 30

seconds every 10 seconds each time it receives a signal

from the transmitter alerting it that no pressure is being

applied on the sensor mat. The receiver will keep ringing

until it is turned o󰀨 or pressure is once again applied on the

sensor mat.

Note: when not used, the power switch of both the

receiver and transmitter should be moved to the “OFF”

position to prevent them from ringing and save battery

life.

OFF

CHIME

ALARM

ALERT ARM

OFF

CHIME

ALARM

ALERT ARM

PAIRING

The pressure sensor mat and wireless receiver are

delivered already paired. When setting them up for the

rst time, you should apply pressure on the sensor mat

to make sure this triggers the alarm, which ought to be

placed less than 30 meters away.

Material :

Plastic PVC

UGEnACPSA200

ALERT ARM

The middle LED (3) will start ashing to warn you that

the battery needs to be replaced.

For product support and help visit our

website at

www.geemarc.com

E-mail : help@geemarc.com

telephone 01707 387602

lines are open 09h00 to 16h00 Mon

to Fri

Parc de l’Etoile, 2 Rue Galilée, 59760

Grande-Synthe,France.

This product is made in China To

Geemarc Telecom

TECHNICAL CHARACTERISTICS

TROUBLE SHOOTING

As soon as you hear a short tone, you can release the “learn”

button. The wireless receiver is now in learning mode and

is ready to receive a pairing signal from your sensor mat’s

transmitter.

3. Move the power slide switch of your sensor mat’s

transmitter to either the “ALERT ARM” or “ ” position without

applying pressure to the mat.

4. If you hear four consecutive short tones coming from the

receiver, this means the pairing process has succeeded.

To unpair a wireless receiver, press and hold its “learn” button

for 12 seconds until you hear two long tones. This indicates

the receiver is no longer paired to any pressure sensor mat.

Range: 30-meter

Frequency: 433.92Mhz

Ringer volume:

- 75dB on the transmitter

85dB (HI) or 70dB (LO) on the receiver

Power:

One 9V battery (type PP3) for the transmitter

Three 1.5V batteries (type LR14) for the receiver

Up to 10 receivers for each transmitter

Radio frequency power < 250mW

Number of receivers for one transmitter: 10

1) If the receiver does not ring, make sure that:

2) If the receiver does not ring, make sure that:

1. The power slide switch of the receiver is either on the “ALARM” or

“ ” positionCHIME

2. The power slide switch of the transmitter is either on the “ALERT”

or “ ” positionARM

3. The transmitter and receptor are not more than 30 meters apart

4. There is no pressure applied to the sensor mat

5. The batteries don’t need to be changed

1. The power slide switch of the transmitter is either on the “ALERT”

or “ ” positionARM

2. There is no pressure applied to the sensor mat

3. The batteries don’t need to be changed

WARRANTY

From the moment your Geemarc AMPLICALL PSA 200 product

is purchased,Geemarc guarantee it for the period of two years.

During this time, all repairs or replacements (at our discretion)

are free of charge. Should you experience a problem then

contact our Helpline or visit our website at www.geemarc.

com. The guarantee does not cover accidents, negligence or

breakage to any parts. The product must not be tampered with

or taken apart by anyone who is not an authorised Geemarc

representative. The Geemarc guarantee in no way limits your

legal rights.

Important: YOUR RECEIPT IS PART OF YOUR

GUARANTEE

AND MUST BE RETAINED AND PRODUCED IN THE EVENT

OF A WARRANTY CLAIM.

Please note: The guarantee applies to the United Kingdom

only.

Geemarc Telecom SA hereby declares that this AMPLICALL

PSA 200 is in compliance with the essential requirements and

other relevant provisions of the Radio Equipment Directive

2014/53/UE.

The declaration of conformity may be consulted at

www.geemarc.com

UKCA DECLARATION

The symbol on the product or its packaging indicates that this

product may not be treated as household waste. Instead it

should be handed over to the applicable collection point for the

recycling of electrical and electronic equipment. By ensuring this

product is disposed of correctly, you will help prevent potential

negative consequences for the environment and human health,

which could otherwise be caused by inappropriate waste

handling of this product. For more detailed information about

recycling this product, please contact your local council o󰀩ce,

your household waste disposal service or the shop where the

product was purchased.

Disposal of old electrical & electronic equipment

(applicable in the European Union and other

European countries with separate collection

systems)

DISPOSAL INFORMATION

1. Move the receiver’s power slide switch to either the

“ ” or “ ” position. You will hear a tone. It ALARM CHIME

indicates that the receiver has been activated and is now in

standby mode.

2. When in standby mode, you can use the tip of a pencil or a

screwdriver to press and hold the “learn” button that is on the

back of the wireless receiver for about 3 seconds.

You can pair up to 10 wireless receivers to a single pressure

sensor mat. To pair new receiver, you should follow the steps

below :

UGEnACPSA200

“This device complies with Industry Canada’s license-

exempt RSSs. Operation is subject to the following two

conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including

interference that may cause undesired operation of the

device.”

FCC CLASS B

NOTE: This equipment has been tested and found

to comply with the limits for a Class B digital device,

pursuant to Part 15 of FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference will not occur

in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined

by turning the equipment o󰀨 and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Re-orient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit di󰀨erent from that

to which the receiver is connected.

• Consult the dealer or an experienced radio TV technician for help.

NOTICE: This This class B digital apparatus complies with Canadian

ICES-003. This product meets the applicable Industry Canada

technical specications.

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) this device may

not cause harmful interference, and (2) this devise must

accept any interference received, including interference

that may cause undesired operation.

Specyfikacje produktu

Marka:	Geemarc
Kategoria:	Niesklasyfikowane
Model:	AMPLICALL PSA200

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Geemarc AMPLICALL PSA200, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Niesklasyfikowane Geemarc

Geemarc AMPLICALL 110 Instrukcja

4 Października 2024

Geemarc AMPLICALL 150 Instrukcja

4 Października 2024

Geemarc AMPLICALL 6-LR Instrukcja

4 Października 2024

Geemarc AMPLICALL 140 Instrukcja

4 Października 2024

Geemarc AMPLICALL 101 Instrukcja

4 Października 2024

Geemarc AMPLICALL PSA200 Instrukcja

4 Października 2024

Geemarc CL7100 Instrukcja

20 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024

Stihl HT 70 Instrukcja

15 Października 2024

Ernesto H14270 Instrukcja

15 Października 2024

Uniden BT MIC KIT Instrukcja

15 Października 2024

Vaude Omnis Bike 26 Instrukcja

15 Października 2024

ART ProChannel II Instrukcja

15 Października 2024

Aukey DR02J Instrukcja

15 Października 2024

Master Lock 653EURD Instrukcja

15 Października 2024

Roland FR-18 Diatonic Instrukcja

15 Października 2024