Instrukcja obsługi GE Profile JD968KKCC
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla GE Profile JD968KKCC (16 stron) w kategorii piec. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/16

1
Before You Begin
Read these instructions carefully and completely.
•IMPORTANT—Save these
instructions for local inspector’s use.
•IMPORTANT—Observe all
governing codes and ordinances.
• Note to Installer—Be sure to leave these
instructions with the consumer.
• Note to Consumer—Keep these
instructions for future reference.
• Proper installation is the responsibility
of the installer and product failure due
to improper installation is NOT covered
under the warranty.
• NOTE—This appliance must be properly
grounded.
•ATTENTION INSTALLER
All electric drop-in ranges must be hard
wired (direct wired) into an approved
junction box. A plug and receptacle is NOT
permitted on these products.
If you have questions, call 1.800.GE.CARES or visit our website at:
ge.com
Self-Cleaning Radiant
Electric Drop-In Range
Installation
Instructions JDP47, JD968, JD900
Materials Needed
Junction Box Wire NutsStrain Relief Clamp
for 1/2” conduit
Parts Included
Lower Trim
2 Screws
2 Shoulder Screws
(for stop device)
Tools You Will Need
1/8” Drill Bit and
Electric or Hand Drill
Phillips Screwdriver
Nut Driver
Level
Tape Measure
Straight Edge
or Square
Hand or Sabre Saw
Standard Screwdriver
Pencil
Safety Glasses
Hammer
31-10622-1 1-07 JR

2
IMPORTANT SAFETY INSTRUCTIONS
Installation Instructions
For Your Safety
• All rough-in and spacing dimensions must be
met for safe use of your range.
• To reduce the risk of burns or fire when
reaching over hot surface elements, cabinet
storage space above the cooktop should be
avoided. If cabinet storage space is to be
provided above the cooktop, the risk can be
reduced by installing a range hood that sticks
out at least 5 beyond the front of the”
cabinets. Cabinets installed above the
cooktop must be no deeper than 13”.
• Be sure your appliance is properly installed
and grounded by a qualified technician.
We recommend you have the electrical wiring
and hookup of your range connected by a
qualified electrician. After installation, have
the electrician show you where your main
range disconnect is located.
Check with your local utilities for electrical
codes which apply in your area. Failure to
wire your range according to governing codes
could result in a hazardous condition. If there
are no local codes, your range must be wired
and fused to meet the requirements of the
National Electrical Code, ANSI/NFPA No. 70–
Latest Edition. You can get a copy by writing:
National Fire Protection Association
Batterymarch Park
Quincy, MA 02269
Effective January 1, 1996, the National
Electrical Code requires that new, but not
existing, construction utilize a four-conductor
connection to an electric range. When
installing an electric range in new construction,
a mobile home, recreational vehicle or an area
where local codes prohibit grounding through
the neutral conductor, follow the instructions in
the section on NEW CONSTRUCTION AND
FOUR-CONDUCTOR BRANCH CIRCUIT
CONNECTION.
You must use a three-wire, single-phase A.C.
208Y/120 Volt or 240/120 Volt, 60 hertz
electrical system. If you connect to aluminum
wiring, properly installed connectors approved
for use with aluminum wiring must be used.
WARNING:
For personal
safety, remove house fuse or
open circuit breaker before
beginning installation. Failure to do so
could result in serious injury or death.
Rating Plate
Location
Electrical
Requirements
This appliance must be supplied with the
proper voltage and frequency, and connected
to an individual, properly grounded branch
circuit, protected by a circuit breaker or fuse
having amperage as noted on rating plate.
(Rating Plate is located behind the oven door
on the range.)

3(Continued on following page)
Door removal is not a requirement for
installation of the product, but is an added
convenience. To remove the door:
Open the oven door as far as it will go.
Push both hinge
locks down toward
the door frame,
to the unlocked
position. This may
require a flat blade
screwdriver.
NOTE: The oven door is very heavy.
Be sure you have a firm grip before lifting
the oven door off the hinges. Use caution
once the door is removed. Do not lay the
door on its handle. This could cause dents
or scratches.
Installation Instructions
Pre-Installation Checklist
Hinge
Unlocked
Position
Hinge
Slot
Hinge
Arm
Place hands on both sides of
the door, and close the oven
door to the removal position.
This is half way between the
broil stop and fully closed.
Lift door up and
out until the
hinge arms
clear the slots.
Hinge
Unlocked
Position
Hinge
Slot
Hinge
Arm
DO NOT LIFT THE DOOR
BY THE HANDLE!
Inspect Installation Location
Protect the kitchen floor! Flatten and
place a piece of the shipping carton in
front of the installation location to protect
the flooring.
Move Range Indoors In Front of
Cabinet Opening
(Do not use hand trucks when
moving the unpackaged range.
Cooktop glass may be broken.)
To obtain Kits:
a. Visit GE Web Site (See page 1)
b. Call GE Answer Center (See page 1)
c. Contact Dealer
Do not remove the protective
channel from the sides of the glass
cooktop until later in installation.
(If supplied)
Inspect cutout dimensions and location
of electrical junction box to be sure it fits
within the layout location. See page 4.
Refer to alternate construction section for
the following non-standard installations.
a.
Counter opening extends to the wall:
Maintop Filler Kit (JXS66XX), or
Backguard Kit (JXS36XX or JXS39SS).
WARNING: If you do not use these
kits, the anti-tip bracket must fit under
an attachment to the wall that can
withstand a force of 200lbs. in the
upward direction. See Section D1.
b. Island Installation:
To provide an optimum installation, the
top surface of the countertop must be
level and flat (lie on the same plane)
around the 3 sides that are adjacent to
range cooktop. Proper adjustments to
make the top flat should be made or
gaps between the countertop and
range cooktop may occur. Forcing the
cooktop to fit may cause excessive
gaps, or could break the glass cooktop
and void the warranty.
Remove packing materials. Remove
labels on door, plastic on trims and
panel, and all tape around the range.
Hinge Clears Slot
Specyfikacje produktu
Marka: | GE |
Kategoria: | piec |
Model: | Profile JD968KKCC |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z GE Profile JD968KKCC, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje piec GE

19 Września 2024

31 Maja 2024

29 Maja 2024

29 Maja 2024

29 Maja 2024

28 Maja 2024

28 Maja 2024

28 Maja 2024

28 Maja 2024

27 Maja 2024
Instrukcje piec
- piec Bauknecht
- piec Ikea
- piec Samsung
- piec Bertazzoni
- piec Electrolux
- piec DeLonghi
- piec AEG
- piec Balay
- piec Beko
- piec Teka
- piec LG
- piec Küppersbusch
- piec Smeg
- piec Götze & Jensen
- piec Gram
- piec Amica
- piec Gorenje
- piec Etna
- piec LERAN
- piec Cookology
- piec Russell Hobbs
- piec Tefal
- piec Livoo
- piec SilverCrest
- piec Dometic
- piec Bosch
- piec Xblitz
- piec Candy
- piec Whirlpool
- piec Miele
- piec Brentwood
- piec Midea
- piec Lamona
- piec Severin
- piec Panasonic
- piec Liebherr
- piec Baumatic
- piec OK
- piec Hoover
- piec Westinghouse
- piec Rinnai
- piec Hendi
- piec Domo
- piec ILive
- piec Ardes
- piec Taurus
- piec Orbegozo
- piec Blaupunkt
- piec Brandt
- piec Vivax
- piec Siemens
- piec Danby
- piec Grundig
- piec Haier
- piec KKT Kolbe
- piec Cylinda
- piec Jocel
- piec Hyundai
- piec Silverline
- piec Blomberg
- piec Bimar
- piec Husqvarna
- piec Concept
- piec Fisher & Paykel
- piec ECG
- piec Indesit
- piec Matsui
- piec Ilve
- piec Unold
- piec Viking
- piec Nodor
- piec CATA
- piec Hotpoint
- piec Kenwood
- piec V-Zug
- piec Ariston Thermo
- piec 70mai
- piec Mestic
- piec PKM
- piec Cuisinart
- piec Wilfa
- piec Thor
- piec Amana
- piec Dacor
- piec Hotpoint Ariston
- piec Meireles
- piec Melissa
- piec Schneider
- piec Thetford
- piec MPM
- piec OneConcept
- piec CDA
- piec Philco
- piec Neff
- piec Corbero
- piec Zanussi
- piec Ravanson
- piec Thermex
- piec Fagor
- piec Koenic
- piec Thomson
- piec Bröhn
- piec Izzy
- piec Klarstein
- piec Artusi
- piec KitchenAid
- piec Steba
- piec Mastercook
- piec TriStar
- piec Landmann
- piec Exquisit
- piec Bartscher
- piec Privileg
- piec Dimplex
- piec Falmec
- piec Arçelik
- piec Hanseatic
- piec Continental Edison
- piec Atag
- piec Rosieres
- piec Franke
- piec G3 Ferrari
- piec Hamilton Beach
- piec Novy
- piec Inventum
- piec SVAN
- piec Euro Appliances
- piec Waring Commercial
- piec Mora
- piec Caple
- piec AEG-Electrolux
- piec Omega
- piec Bush
- piec Kenmore
- piec Kaiser
- piec BORA
- piec VOX
- piec Pelgrim
- piec Benavent
- piec Orima
- piec Rex
- piec Kernau
- piec Technika
- piec JennAir
- piec Frigidaire
- piec RCA
- piec Summit
- piec Gemini
- piec Foster
- piec Chef
- piec Rommelsbacher
- piec Fulgor Milano
- piec Kelvinator
- piec Gaggenau
- piec Sencor
- piec Avanti
- piec Asko
- piec Altus
- piec Esatto
- piec Signature
- piec Capital
- piec BlueStar
- piec Becken
- piec Scandomestic
- piec Guzzanti
- piec Steel
- piec Aroma
- piec Edilkamin
- piec Campart
- piec Belling
- piec De Dietrich
- piec ZLine
- piec Cotech
- piec Campingaz
- piec Magic Chef
- piec Eurom
- piec Clas Ohlson
- piec Arctic Cooling
- piec Sauber
- piec Smith&Brown
- piec Sogo
- piec Crosley
- piec Nutrichef
- piec Constructa
- piec Proline
- piec Euromaid
- piec BLANCO
- piec Emax
- piec Thermador
- piec Finlux
- piec Bestron
- piec VIOFO
- piec Optimum
- piec Rotel
- piec Atlas
- piec Kluge
- piec Arthur Martin
- piec Logik
- piec Profilo
- piec Eldom
- piec Leisure
- piec Glem Gas
- piec Proctor Silex
- piec Creda
- piec Cadac
- piec Waves
- piec ARC
- piec Orava
Najnowsze instrukcje dla piec

28 Października 2024

28 Października 2024

28 Października 2024

28 Października 2024

27 Października 2024

21 Października 2024

12 Października 2024

11 Października 2024

11 Października 2024

9 Października 2024