Instrukcja obsługi GE JX1827CB

GE mikrofala JX1827CB

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla GE JX1827CB (4 stron) w kategorii mikrofala. Ta instrukcja była pomocna dla 31 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/4
PART QUANTITY
Trim Frame 1
Bottom Duct 1
Side Duct 1
1” Screws 6
(4 required, 2 extra)
1/2” Screws 15
(11 required, 4 extra)
Anti-Tip Bracket 1
Bottom Bracket 1
Upper Duct 1
Template 1
PARTS INCLUDED
Questions? Call GE Answer Center at 800.626.2000
or Visit our Website at:
www.GEAppliances.com
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
Installation Built-In Trim Kits
Instructions
JX1827 and JX1830
Read these instructions completely and carefully.
•IMPORTANT –Save these
instructions for local inspector’s use.
•IMPORTANT –Observe all
governing codes and ordinances.
•Note to Installer –Be sure to leave these
instructions with the Consumer.
•Note to Consumer –Keep these
instructions for future reference.
BEFORE YOU BEGIN
• Unplug the microwave oven before attempting
installation of this kit.
• Skill level – Installation of this appliance requires basic
mechanical and electrical skills.
• Completion time – 1-3 hours
• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not
covered under the Warranty.
• This kit is UL listed for installation alone or over any
General Electric/Hotpoint/RCA single electric wall
oven.
TOOLS YOU WILL NEED
Phillips screwdriver
Pencil
Tape measureAwl or punch
Drill with 7⁄64″bit or #35
1
FOR YOUR SAFETY:
WARNING –Before beginning the
installation, switch power off at service panel and lock
the service disconnecting means to prevent power
from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten
a prominent warning device, such as a tag, to the
service panel.
2
CUTOUT DIMENSIONS1.
* Min. depth with receptacle outside cabinet 191⁄2″
Min. depth with receptacle inside cabinet 22″
Installation Instructions
Models 27″ ″30
Height 163⁄ 164″3⁄4″
Width 251⁄ 252″1⁄2″
Depth (min.)* 191⁄ 192″or 22″1⁄2″or 22″
On 27 models, allow 1 at the top, ″ ″ 11⁄16″on the sides
and 13⁄8″at the bottom for overlap of the Trim Frame
over the edges of the cutout.
On 30 models, allow 1 at the top, 2″ ″ 3⁄16″on the sides
and 13⁄8″at the bottom for overlap of the Trim Frame
over the edges of the cutout.
Depth
Height
3 Min.″
Width
INSTALL BOTTOM BRACKET
AND BOTTOM DUCT
2.
Disconnect the microwave oven before proceeding
with the installation.
Fasten the bottom bracket to the bottom duct by
using two 1⁄2″screws.
Remove any loose items inside the microwave
oven, including the turntable and turntable
support. Carefully turn the microwave upside
down.
Install bottom duct with four 1⁄2″screws as shown.
A
C
B
D
Front
Rear
1⁄2″Screws (2)
Screws
Screws
Microwave Oven Upside Down
3
Installation Instructions
INSTALL THE ANTI-TIP BRACKET3.
Fold or cut the front edge of the template, along
the front guide line. Place the template flush along
the front edge of the cutout floor, aligning the
center line of the template with the center line of
the cutout floor. Mark the center positions with an
awl or center punch for the anti-tip bracket
location as shown.
Remove the template and drill two holes for the
anti-tip bracket.
Install the anti-tip bracket onto the cutout floor
using two 1⁄2″screws.
A
B
C
Cutout Floor
1⁄2″Screws (2)
Anti-Tip Bracket
INSTALL SIDE DUCT AND UPPER
DUCT
4.
Connect the side duct to the upper duct as shown.
1. Insert projecting tabs of the upper duct into the
holes of the side duct.
2. Bend the tabs up with caution as shown.
NOTE: Remove any oil or dirt on the surface of the
microwave oven before the ducts are attached.
Set the microwave upright, being careful not to
bend the front flange. Remove the one existing
screw from the left side of the microwave oven.
Peel off the backing of the double sided tape.
Carefully position the side duct and upper duct
assembly on the microwave cabinet, aligning with
the bottom screw hole. Press down firmly on the
ducts. Fasten the duct assembly to the left side of
the cabinet with the screw removed above.
B
A
(2)
C
Existing Screw (1)
(1)
Upper Duct
Side Duct
3 Tabs
3 Holes

Specyfikacje produktu

Marka: GE
Kategoria: mikrofala
Model: JX1827CB

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z GE JX1827CB, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje mikrofala GE

GE

GE JX1527CBC Instrukcja

29 Maja 2024
GE

GE JVM1752DPBB Instrukcja

28 Maja 2024
GE

GE JX1827CB Instrukcja

24 Maja 2024
GE

GE JVM1441WH Instrukcja

17 Maja 2024
GE

GE JVM1950DRBB Instrukcja

14 Maja 2024
GE

GE SCB2000CCC Instrukcja

14 Maja 2024
GE

GE JX1530SMSS Instrukcja

13 Maja 2024
GE

GE JX7230BLTS Instrukcja

11 Maja 2024
GE

GE JX52BL Instrukcja

8 Maja 2024
GE

GE JES0734PMRR Instrukcja

7 Maja 2024

Instrukcje mikrofala

Najnowsze instrukcje dla mikrofala

Scancool

Scancool MWP34X Instrukcja

30 Września 2024
Daewoo

Daewoo KOC-9C0TC Instrukcja

26 Września 2024
Daewoo

Daewoo KOR-137H Instrukcja

26 Września 2024
Insignia

Insignia NS-OTR16SS8Q Instrukcja

25 Września 2024
Siemens

Siemens BF722L1B1 Instrukcja

23 Września 2024
Siemens

Siemens BF922L1B1 Instrukcja

23 Września 2024
Siemens

Siemens CE732GX.1 Instrukcja

23 Września 2024
Siemens

Siemens BF922R1B1 Instrukcja

23 Września 2024
CATA

CATA BI2505DCG BK Instrukcja

21 Września 2024
Zanussi

Zanussi ZVENW6X3 Instrukcja

21 Września 2024