Instrukcja obsługi GE GXWH08C

GE Filtr wody GXWH08C

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla GE GXWH08C (12 stron) w kategorii Filtr wody. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/12
REQUIRED TOOLS AND ACCESSORIES
FOR INSTALLATION
2 wrenches: 118and 114
Pipe cutter or hacksaw
File
Emery paper
Screwdriver
For GXWH01C model, additional installation parts may
be required:
(2) 34compression adapters with brass ferrule and
nut for installation on copper plumbing
Installation Kit available:
Retail Part (WHKIT)
GE Parts (WS35X10023)
UL-approved grounding clamps and 8-gauge copper
grounding wire–Installation Kit available:
Retail Part (WHKIT)
GE Parts (WS35X10023)
Teflon®Tape
Sump Wrench
Retail Part (UCWRNCH)
GE Parts (WX5X140)
Optional accessories are available (Visa, MasterCard or Discover
cards accepted) by visiting our Website at www.GEAppliances.com
or from Parts and Accessories 800.626.2002 (U.S.) or
800.663.6060 (Canada).
If unit is to be installed on plastic, PVC, or galvanized
plumbing, separate hardware must be purchased.
CONTENTS INCLUDED WITH PRODUCT
Filter housing and head
Product literature
Sediment filter
(for GXWH08C)
(2)
34
brass compression adapters with nut
and ferrule (for GXWH08C)
Teflon®tape (for GXWH08C)
Sump wrench (for GXWH08C)
Grounding clamps and wire (for GXWH08C)
1
GE Smar tWater
INSTALLATION INSTRUCTIONS
Household Water Filtration System GXWH01C and GXWH08C
251B6021P001 10-01 JR 49-50043-3
www.GEAppliances.com
GENERAL ELECTRIC COMPANY, Appliance Park, Louisville, KY 40225
SAFETY PRECAUTIONS
Check with your state and local public works
department for plumbing and sanitation codes.
You must follow these guidelines as you install
the Household Water Filtration System. Using
a qualified installer is recommended.
Be sure the water supply conforms with the Specifications
Guidelines. If the water supply conditions are unknown,
contact your municipal water company
.
WARNING: Do not use with water that is
microbiologically unsafe or of unknown quality
without adequate disinfection before or after the system.
I
t is highly recommended that a water shut-off valve
be placed directly upstream of your household filter.
PROPER INSTALLATION
Check with your local public works department for
plumbing codes. You must follow their guides as you
install the Household Water Filtration System.
Use the Household Water Filtration System on a potable,
safe-to-drink, home COLD water supply only. The filter
cartridge will not purify water or make unsafe water safe
to drink. DO NOT use on HOT water (100˚F max).
Protect the Household Water Filtration System and piping
from freezing. Water freezing in the system will damage it.
Your Household Water Filtration System will withstand up to
125 psi water pressure. If your house water supply pressure
is higher than 100 psi during the day (it may reach higher
levels at night), install a pressure-reducing valve before the
system is installed.
Do not install on HOT WATER. The temperature of the
water supply to the Household Filtration System must
be between the minimum of 40
°F and the maximum
of
1
00°F
. See the Specification Guidelines
.
Do not install the Household Water Filtration System
using copper solder fittings. The heat from the soldering
process will damage the unit.
WARNING: Discard all unused parts and packaging
material after installation. Small parts remaining after
installation could be a choke hazard.
Do not install filter in an outside location or anywhere
it will be exposed to sunlight.
This Household Water Filtration System must be properly installed and located in accordance with the Installation Instructions before it is used.
System is
Tested and Certified by NSF
International against ANSI/NSF
Standard
42 for nominal Particulate Reduction
Class . III
System is
Tested and Certified by NSF
International against ANSI/NSF
Standard
42 for nominal Particulate Reduction
Class . III
GXWH01C GXWH08C
2
ABOUT THE FILTER CARTRIDGE
Filter Cartridge Replacement
You should change your filter when the water flow is noticeably reduced or at least every three months.
Filter Cartridge Life
Several variables determine how long
the cartridge will last in your Household
Water Filtration System. These include:
levels of sediment or other undesirable
substances in your water.
the amount of water you use.
the filter location (filtering all or part of your
household water).
GE MODEL FUNCTION LIFE CONSTRUCTION
FXUSC* Sediment 3 month/16,000 gallons Polyspun
15 Micron
FXWPC Sediment 3 month/16,000 gallons Pleated
FXWSC Sediment 3 month/16,000 gallons String Wound
10 Micron
FXWTC* Sediment 3 month/15,000 gallons Carbon Paper
5 Micron
Chlorine
*NSF Certification for particulate reduction applies only to the FXUSC and FXWTC when
used in GXWH01C or GXWH08C Filtration Systems.
Turn off water to filter. For model GXWH01C,
water must be shut off from an upstream
valve. For model GXWH08C, rotate bypass
valve to the bypass position.
Press the red pressure release button to release
pressure.
Unscrew the filter canister and discard used
filter. Wash the filter canister with mild soap
and water. Do not use harsh cleaners or hot
water.
Inspect the filter canister O-ring. Make sure it
is lightly lubricated and completely seated in
the groove. It is recommended that you
replace the O-ring if it is damaged.
Place a new filter cartridge into the canister
making sure it is centered and completely
seated on the bottom seal.
Reinstall the filter canister to the unit. Hand
tightening is all that is required to seal the
unit.
Slowly turn on water to the filter by using the
bypass valve (model GXWH08C) or the
upstream shut-off valve.
Press the red pressure release button to
remove trapped air.
Open any downstream faucet and allow filter
system to flush for 5 minutes.
9
8
7
6
5
4
3
2
1
Installation Overview
NOTE: Be sure to allow a minimum space of 112
under the filter for removing the sump, to change
the cartridge.
Turn sump wrench tool
clockwise to remove
(on some models) Sump
Bypass valve
Filter
cartridge O-ring seal
Red pressure
release button
Head
Filter canister
Turn
clockwise
to remove
canister
Turn
counterclockwise
to tighten
Turn
clockwise
to remove
canister
Turn
counterclockwise
to tighten
Red pressure
release button
Filter
cartridge O-ring seal
Filter canister
Head
GXWH01C GXWH08C
Recommended
shut-off valve Recommended
shut-off valve
GXWH01C GXWH08C
Specification Guidelines
Minimum–Maximum Supply Water Pressure: 20–125 pounds per square inch (psi)
Minimum–Maximum Supply Water Temperature: 40°F/100°F Rated Service Flow: 4 gpm
Recommended
shut-off valve
Recommended
shut-off valve
STEP-BY-STEP INSTALLATION INSTRUCTIONS
3
STEP-BY-STEP INSTALLATION INSTRUCTIONS (cont.)
Select Location
Select a location for the filter that is:
protected from freezing.
not exposed to direct sunlight.
It is recommended that a shut-off valve be placed on both sides
of the filter.
Install Fittings
Instructions are for installing fittings supplied with the
filter (on some models) or the WHKIT onto 3/4copper
plumbing. If the unit is to be installed on any other type of
tubing (plastic, PVC, galvanized), different hardware must be
purchased. See instructions with additional hardware
purchased, or consult a qualified plumber.
Apply about 6of Teflon®tape, in a clockwise direction, to
the pipe threads (course) of each adapter. DO NOT use joint
compound on any parts.
Assemble an adapter to the inlet and outlet of the head.
Start each fitting by hand to make sure they don’t cross
thread. Use a 118wrench firmly. DO NOT OVERTIGHTEN.
About one to two thread(s) should remain visible.
Cut Water Line
Turn off water supply and open a nearby faucet to drain
water out of pipes.
Remove the nut and brass ferrule from both compression
fittings and set aside. Using a tape measure or ruler,
measure the distance D” as shown.
NOTE: I
t is recommended that the shut-off valve be placed
before and after the filter as shown in the Installation
Overview illustration.
Select the location for the filter. Mark the distance D”
on the pipe.
Using a pipe cutter or hacksaw, cut pipe. Sand (file) cut
ends of pipe to assure that they are square and smooth.
3
2
1
Attach Fittings to Water Line
Slip a compression nut onto each pipe.
Next, slip the brass ferrule onto each pipe.
2
1
Nut
Brass ferrule
Nut
Brass ferrule
Measure to shoulder
of fittings. Copper
pipe butts against
this shoulder.
DD
GXWH01C GXWH08C
Installing the Ground Wire
IMPORTANT: A copper or galvanized house cold water pipe is often
used to ground electrical outlets in the home. Grounding protects you
from electrical shock. The water filter housing may have broken this
ground path. To restore connection, install a 12long, 8-gauge
copper wire across the filter, tightly clamped using UL-approved
1/2–1bronze grounding clamps at both ends as shown. Zinc
clamps should not be used on copper plumbing. For GXWH01C,
wire and clamps may be purchased separately from your local
hardware store, or are available by visiting our Website at
www.GEAppliances.com, or from Parts and Accessories by calling
800.626.2002 (U.S.)or 800.663.6060 (Canada) – order part
number WHKIT.
Clean copper pipe and ends of wire with emery paper. Bare wire
is recommended. If insulated wire is used, it should be stripped
3/4at each end before cleaning with emery paper.
Attach bronze clamps to copper pipe. Tighten screws.
Attach wire to clamps as shown. Tighten screws.
NOTE: If your house plumbing is plastic, it would not be used as a
grounding path, and this step should be skipped.
3
2
1
Clamp
Final Check
Install filter, if not all ready done. (See Filter Cartridge
Replacement section.)
Slowly turn on water supply.
Check entire system for leaks.
If leaking, shut off water pressure and tighten or reseal
fittings.
Open any downstream faucet and allow filter system to
flush for 5 minutes.
5
4
3
2
1
D
Ground wire
Teflon®tape
Installing the Unit
Align filter assembly with pipe ends making certain that the
incoming water supply is going into the filter opening marked
“IN”. It may be necessary to spread the pipe ends apart to install
filter assembly.
Using a 118wrench to hold the adapter in place, use a 114
wrench to tighten the nut. Repeat process for other fittings.
If necessary, support the water pipe on either side of the filter
unit.
3
2
1


Specyfikacje produktu

Marka: GE
Kategoria: Filtr wody
Model: GXWH08C
Kolor produktu: Black,Green
Typ produktu: Bujanka dla niemowląt
Wysokość produktu: 2165 mm
Szerokość produktu: 2646 mm
Głębokość produktu: 2352 mm
Waga produktu: 40000 g
Certyfikat środowiskowy (zrównoważonego rozwoju): Forest Stewardship Council (FSC)
Przeznaczenie: Zewnętrzna
Waga wraz z opakowaniem: 41600 g
Produktów na palecie: 20 szt.
Maksymalna waga: 100 kg
Wodoodporny: Tak
Zalecany wiek (min): - mies.
Materiały: Drewno
Zalecany wiek (max): - mies.
Tworzywo ramy: Drewno
Maksymalne obiążenie: 100 kg
Regulowana wysokość: Tak
Liczba siedzeń: 1 siedz.
Materiał siedziska: Tkanina
Typ siedziska: Siedzenie gniazdo huśtawki
Liczba opakowań: 2
Liczba kotwic w zestawie: 4
Typ instalacji: Wolnostojący
Średnica siedziska: 980 mm
Szerokość słupka: 69 mm
Głębokość słupka: 69 mm
Szerokość belki: 69 mm
Głębokość belki: 92 mm
Opakowanie 1 Wymiary (SxGxW): 2370 x 150 x 240 mm
Wymiary opakowania 2 (S x W x G): 275 x 235 x 480 mm

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z GE GXWH08C, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Filtr wody GE

GE

GE GX1S15C Instrukcja

13 Października 2024
GE

GE GXSF18G Instrukcja

4 Października 2024
GE

GE GNSV30CWW Instrukcja

14 Września 2024
GE

GE GXCF20KWW Instrukcja

12 Września 2024
GE

GE GNWH08C Instrukcja

30 Sierpnia 2024
GE

GE GNWH38S Instrukcja

29 Sierpnia 2024
GE

GE GXWH08C Instrukcja

14 Sierpnia 2024
GE

GE GNSV75RWW Instrukcja

9 Sierpnia 2024

Instrukcje Filtr wody

Najnowsze instrukcje dla Filtr wody

Laica

Laica J35-AD Instrukcja

15 Października 2024
Laica

Laica J35-EB Instrukcja

15 Października 2024
Laica

Laica J11-AB Instrukcja

15 Października 2024
Laica

Laica J51-BC Instrukcja

15 Października 2024
Grohe

Grohe Red Instrukcja

11 Października 2024
Fluval

Fluval AquaClear AC30 Instrukcja

9 Października 2024
Fluval

Fluval AquaClear AC50 Instrukcja

9 Października 2024
Fluval

Fluval AquaClear AC20 Instrukcja

9 Października 2024
Fluval

Fluval AquaClear AC70 Instrukcja

9 Października 2024
Eden

Eden 316 Instrukcja

8 Października 2024