Instrukcja obsługi Fusion RE-AM45020

Fusion Radio samochodowe/odtwarzacz CD RE-AM45020

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Fusion RE-AM45020 (2 stron) w kategorii Radio samochodowe/odtwarzacz CD. Ta instrukcja była pomocna dla 11 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
REACTOR
AMPLIFIERS
RE-AM45020, RE-AM90010, RE-AM90040
Amplifier Specifications
Installation Guidelines
1. Ensure the +12v lead is disconnected from the battery before you connect any new equipment.
2. Ensure the mounting location will not interfere with the gas tank, brake lines or electrical wiring.
3. Ensure the Amplifier is securely fastened to the vehicle to prevent damage in the event of an accident.
4. Ensure all wiring is protected to avoid pinching or crushing which could result in damage to the audio system.
5. Ensure the mounting location has sufficient air flow around the amplifier. If the amplifier is mounted in an enclosed space a
3” fan with ducting should be used to aid in air flow.
6. Do not mount any amplifier on a subwoofer enclosure as extended exposure to vibration may cause malfunction of the
amplifier.
7. Ensure you use the recommended gauge wire/cable for all amplifier connections.
Wiring
Ensure the audio system is turned off before making any connections to the amplifier, speakers or source unit.
Failure to do so could result in permanent damage to the audio system. When wiring the FUSION amplifier ensure
that the cable is protected from sharp objects and always use rubber grommets when wiring through metal panels.
Ensure all terminals and connections are protected from the vehicle chassis and from each other as failure to do so
could result in permanent damage to the audio system.
Power
FUSION amplifiers should be connected directly to the +12v battery terminal with an inline fuse or circuit breaker as
close to the battery as possible.
Ground
When grounding/earthing your amplifier ensure that the location is a good source of ground (preferably the floor
pan). Make sure the metal is clean of paint etc as a poor earth could damage your audio system.
Remote Turn On
This connection turns the amplifier on and should be connected to the remote turn on wire from the Head Unit. If
one is not available a switched 12v source must be used. Either a power antenna wire or ACC +12v.
Low Level Inputs
Choose the correct length RCA interconnects and run them to the RCA outputs of the source/head unit, avoiding
running beside other looms and or power cable.
Level Control
This control is used to match the input level of the amplifier to the output level of you head unit. We recommend the
following method.
RE-AM45020 RE-AM90010 RE-AM90040
Max Power Rating 450 Watts 900 Watts 900 Watts
Frequency Response 10Hz - 40kHz 10Hz - 250Hz 10Hz - 40kHz
Dimensions (mm) 285(L)x 280(W) x 62(H) 355(L)x 280(W) x 62(H) 405(L)x 280(W) x 62(H)
Power Ratings 90 Watts RMS per Channel
@ 4 Ohms 1% THD+N
130 Watts RMS per Channel
@ 2 Ohms 1% THD+N
250 Watts RMS Bridged Channels
@ 4 Ohms 1% THD+N
240 Watts RMS x 1 Channel
@ 4 Ohms 1% THD+N
350 Watts RMS x 1 Channel
@ 2 Ohms 1% THD+N
90 Watts RMS per Channel
@ 4 Ohms 1% THD+N
125 Watts RMS per Channel
@ 2 Ohms 1% THD+N
230 Watts RMS Bridged Channels
@ 4 Ohms 1% THD+N
Turn the amplifier level to zero
Turn the volume of the head unit to ¾ and the bass and treble to zero
Adjust the level control until the desired maximum volume is achieved without distortion.
Failure to follow these steps may cause permanent damage to the audio system.
Recommended Amplifier Installation Kits
FUSION recommends the following Amplifier Installation Kit to be used with Reactor Amplifiers
RE-AM90010 Reactor Monoblock Amplifier AC- AK04 4 Gauge Installation Kit
RE-AM45020 Reactor 2 Channel Amplifier AC- AK08 8 Gauge Installation Kit
RE-AM90040 Reactor 4 Channel Amplifier AC- AK04 4 Gauge Installation Kit
Trouble Shooting
RECORD YOUR PURCHASE DETAILS HERE:
MODEL NUMBER __________________________ DATE OF PURCHASE__________________________
AFFIX RECEIPT HERE
WARNING! Audio Systems can produce sound levels over 135dB. Continuous exposure to sound pressure levels over 100dB may
cause permanent hearing loss! Please watch for emergency vehicles as warning signals may not be heard. USE COMMON SENSE!
PROBLEM POSSIBLE REASON SOLUTION
Amplifier not switching on.
Power LED
not ‘on’
• No +12v to power wire • Check fuses and connections to battery
• No power to remote wire • Check remote on connections to head unit
• Fuse broken • Replace fuse with correct type and
amperage
Amplifier not working, but
status LED ‘on’
• Fuse on amplifier blown • Replace fuse with correct type and
amperage
• Amplifier too hot • Move amplifier to vented area
• Turn head unit down
• Speaker wires shorted • Check that there are no speaker wires shorted to
another wire or to the vehicle chassis
No sound • RCA Signal • Check RCA connection to head unit
• Gain control not set up • Ensure you have set up the amplifier gain
level control
• Head Unit • Check head unit volume level
• Amplifier • Check all power, remote on and ground
connections
• Speakers • Check speakers for wire shorts
V 4.0

Specyfikacje produktu

Marka: Fusion
Kategoria: Radio samochodowe/odtwarzacz CD
Model: RE-AM45020

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Fusion RE-AM45020, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Radio samochodowe/odtwarzacz CD Fusion

Fusion

Fusion PP-AM8004 Instrukcja

19 Września 2024
Fusion

Fusion PP-AM300010 Instrukcja

18 Września 2024
Fusion

Fusion PP-AM120040 Instrukcja

7 Września 2024
Fusion

Fusion PP-AM60020 Instrukcja

15 Sierpnia 2024
Fusion

Fusion RE-AM45020 Instrukcja

9 Sierpnia 2024

Instrukcje Radio samochodowe/odtwarzacz CD

Najnowsze instrukcje dla Radio samochodowe/odtwarzacz CD

Belson

Belson BS12100 Instrukcja

27 Września 2024
Mx Onda

Mx Onda MX1500 Instrukcja

27 Września 2024
Belson

Belson BS12150 Instrukcja

27 Września 2024
Belson

Belson BS11900 Instrukcja

27 Września 2024
Belson

Belson BS11520 Instrukcja

27 Września 2024
Mx Onda

Mx Onda HUESCA Instrukcja

27 Września 2024
DLS

DLS REFERENCE RA20 Instrukcja

26 Września 2024
DLS

DLS RA 10 Instrukcja

26 Września 2024
Mx Onda

Mx Onda BAEZA Instrukcja

26 Września 2024
Mx Onda

Mx Onda T825M Instrukcja

26 Września 2024