Instrukcja obsługi Frigidaire IM115


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Frigidaire IM115 (7 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/7
ICE MAKER
INSTALLATION
INSTRUCTIONS
P/N 240394901
The following items will be required to install the ice maker kit.
1/4 inch copper supply line with shut o valve
1/4 inch brass compression nut and ferrule
Freezer shelf (Some models not eqipped with shelf). If your
model does not have one, contact your dealer to order one.
The copper tubing and shut o valve are available in a kit from your
local hardware or plumbing supply store. Coil enough tubing at the
back of the unit to allow movement for cleaning.
To Avoid Property Damage:
Copper tubing is recommended for the water supply line. Water supply tubing made of 1/4
plastic is not recommended since it greatly increases the potential for water leaks.
The manufacturer will not be responsible for any damage if plastic tubing is used for the
supply line.
DO NOT install water supply tubing in areas where temperatures fall below freezing.
Connect the ice maker to a drinkable water source that is not tied into a water softening
system. Chemicals from the softener may damage the ice maker, causing it to
malfunction.
To avoid electric shock, which can cause death or severe personal injury,
disconnect the refrigerator from electrical power before connecting a water supply line to
the refrigerator.
2
Tools Required:
Putty Knife Pliers
¼ inch Socket Wrench Needle Nose Pliers
or Nut Driver Adjustable Wrench
 Knife
1. Ice Maker 2. Ice Container 3. Plastic Water Supply Tubing
8. Steel Clamp - Qty 1
4. Screws - Qty 2 5. Screws - Qty 2 7. Leveling Bracket
Qty 1
6. Leveling Bracket
Screw - Qty 1
10. Water Valve - Qty 1 11. Water Inlet Tube - Qty 1
9. Plastic Clamp - Qty 2
Use This Page to Identify Parts
3
1. Unplug refrigerator from wall outlet.
2. Remove ice tray rack from freezer (some models).
3. Remove freezer shelf (some models) by pushing shelf
to left until right side of shelf is out of hole. Slowly lift
up and pull on shelf to remove.
4. Remove plugs from inside freezer compartment
with putty knife.
5. If refrigerator has exterior condenser (C), go to rear of
refrigerator and locate left condenser mounting bracket
screw(s). Remove and save screws. DO NOT remove
compressor sound baffle (A), if installed.Carefully bend
condenser out away from back of refrigerator.
If condenser is mounted inside compressor
compartment (D), remove screws securing
sound baffle to cabinet (B).
7. With needle nose pliers, remove foam from hole.
8. Push water inlet tube into small hole on back of
refrigerator. Rotate while inserting tube until flat
surface of inlet tube is tight against back of
refrigerator.
6. Peel off label covering ice maker hole.


Specyfikacje produktu

Marka: Frigidaire
Kategoria: Niesklasyfikowane
Model: IM115

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Frigidaire IM115, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Niesklasyfikowane Frigidaire

Frigidaire

Frigidaire GDPH4525AF Instrukcja

7 Października 2024
Frigidaire

Frigidaire WOMC3TRIMWHT Instrukcja

6 Października 2024
Frigidaire

Frigidaire GMTK3068AD Instrukcja

4 Października 2024
Frigidaire

Frigidaire FDSR4501AP Instrukcja

3 Października 2024
Frigidaire

Frigidaire CFPWD15W Instrukcja

3 Października 2024
Frigidaire

Frigidaire GLGT1142FS Instrukcja

3 Października 2024
Frigidaire

Frigidaire GMTK2768AD Instrukcja

2 Października 2024
Frigidaire

Frigidaire IM115 Instrukcja

22 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane