Instrukcja obs艂ugi Fredenstein Bento 10 DS
Fredenstein
Maszyna efekt贸w
Bento 10 DS
Przeczytaj poni偶ej 馃摉 instrukcj臋 obs艂ugi w j臋zyku polskim dla Fredenstein Bento 10 DS (9 stron) w kategorii Maszyna efekt贸w. Ta instrukcja by艂a pomocna dla 10 os贸b i zosta艂a oceniona przez 2 u偶ytkownik贸w na 艣rednio 4.5 gwiazdek
Strona 1/9
Bento 10 DS
Module Carrier
Operating Manual
Fredenstein Bento 10 DS Module Carrier
The Fredenstein Bento 10 DS is the most advanced module carrier for ten Fredenstein Series 600
modules or API-500 compatible plug-in cards in 3U 19 inch rack-mount format. The Bento 10 DS
features several important upgrades compared with third party products:
the color LCD Display and a rotary encoder:
to set routing and other parameters with non-volatile storage. In addition, if certain Fredenstein
modules are used, like the F600A, F601A, F602, F603A/B, and the F607, all operating parameters
of theses modules are displayed as well.
Universal power supply:
accepting mains voltages from 90V AC to 240V AC, 50 to 60 Hz.
Increased output currents: 6A or 600 mA per slot and +48V DC 0.25A
Monitoring of output voltages and currents.
Auxiliary Audio Inputs and Outputs
Built-in Audio Routing:
Modules can be daisy-chained by simply using the menu driven user interface on the LCD.
Built-in compatibility switches for non-conforming modules.
Compressor buss linking:
Compressor modules can be linked simply using the menu driven user interface on the LCD as well.
Multi-layer back-plane:
Increased signal integrity and lower noise floor.
Ground-lift :
In case of ground loops, the audio ground and the protective ground can be disconnected. Please use
only if absolutely necessary.
Installation:
Electrical Safety Warnings:
Do not open the enclosure, hazardous voltages are present inside!
There are no user serviceable parts inside.
Always disconnect the mains cord before installing or removing modules!
If you need to replace the mains fuse, make sure the replacement has the same
rating ( 3.15 AT).
Please disconnect the mains from your Bento 10 DS before installing or removing modules. Make
sure each installed module is well seated in the receiving connector and the module is secured by
fasten the two mounting screws (size: M3).
Front View:
Fredenstein Bento 10 DS Manual V1.0 Sep 25, 2017 Page 1
Fredenstein Bento 10 DS Module Carrier
If certain non-Fredenstein modules are used, which bridge several pins on the connector and
connected the contacts on the top and button side, the double switches, located directly besides the
slot connectors, can both be turned off (lower position) to avoid interference between the module
and the digital interconnect. For Fredenstein modules, both need to be in the ON (upper) position.
To rack-mount the unit, the four feet have to be removed by their center screws.
Operation:
After installation of the modules, connect the mains cord to the Bento 10 DS IEC socket located on
the back-panel and than connect the mains cable to a grounded outlet. Now turn the Bento 10 DS on
by operating the I/O switch (also part of the IEC socket on the back). The following screen will be
displayed indicating the status and power-supply voltages and currents.
Now the Bento 10 DS is ready and will display any request from
certain Fredenstein modules. The Bento 10 DS will continuously
monitor the power-supplies and display the voltages and currents.
To enter the setup menu, please push the wheel and the setup menu
will appear.
Configuration of audio linking
Configuration of compressor buss linking
Various Setting
Save Configuration
Recall Configuration
Turning the wheel left or right to scroll from one menu point to the next, the highlighted menu point
will get selected when the wheel is pushed. Selecting Exit and pushing the wheel will show the
Status screen again.
Fredenstein Bento 10 DS Manual V1.0 Sep 25, 2017 Page 2
Specyfikacje produktu
| Marka: | Fredenstein |
| Kategoria: | Maszyna efekt贸w |
| Model: | Bento 10 DS |
Potrzebujesz pomocy?
Je艣li potrzebujesz pomocy z Fredenstein Bento 10 DS, zadaj pytanie poni偶ej, a inni u偶ytkownicy Ci odpowiedz膮
Instrukcje Maszyna efekt贸w Fredenstein
16 Sierpnia 2024
Instrukcje Maszyna efekt贸w
- Maszyna efekt贸w BeamZ
- Maszyna efekt贸w Behringer
- Maszyna efekt贸w American DJ
- Maszyna efekt贸w Chauvet
- Maszyna efekt贸w Antari
- Maszyna efekt贸w Eurolite
- Maszyna efekt贸w Velleman
- Maszyna efekt贸w Manta
- Maszyna efekt贸w Showtec
- Maszyna efekt贸w Klark Teknik
- Maszyna efekt贸w Doepfer
- Maszyna efekt贸w Cameo
- Maszyna efekt贸w Lotronic
- Maszyna efekt贸w Elation
- Maszyna efekt贸w Futurelight
- Maszyna efekt贸w Martin
- Maszyna efekt贸w Monacor
- Maszyna efekt贸w HQ Power
- Maszyna efekt贸w Magmatic
- Maszyna efekt贸w Technical Pro
- Maszyna efekt贸w Adj
- Maszyna efekt贸w Steren
- Maszyna efekt贸w Valcom
- Maszyna efekt贸w QTX
- Maszyna efekt贸w Valueline
- Maszyna efekt贸w Max
- Maszyna efekt贸w Monoprice
- Maszyna efekt贸w ColorKey
- Maszyna efekt贸w Black Lion Audio
- Maszyna efekt贸w Laserworld
- Maszyna efekt贸w JB Systems
- Maszyna efekt贸w Evo-Lite
- Maszyna efekt贸w Blizzard
- Maszyna efekt贸w Hazebase
- Maszyna efekt贸w Sagitter
- Maszyna efekt贸w Fun Generation
- Maszyna efekt贸w IMG Stage Line
- Maszyna efekt贸w Lexicon
- Maszyna efekt贸w The Confetti Maker
- Maszyna efekt贸w BoomTone DJ
- Maszyna efekt贸w TCM FX
Najnowsze instrukcje dla Maszyna efekt贸w
10 Pa藕dziernika 2024
8 Pa藕dziernika 2024
8 Pa藕dziernika 2024
8 Pa藕dziernika 2024
8 Pa藕dziernika 2024
8 Pa藕dziernika 2024
8 Pa藕dziernika 2024
8 Pa藕dziernika 2024
8 Pa藕dziernika 2024
8 Pa藕dziernika 2024