Instrukcja obsługi Foscam FN8108W-B4

Foscam nieskategoryzowany FN8108W-B4

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Foscam FN8108W-B4 (2 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
123 4 5
7 98 10 11 12
Quick Setup Guide
Security Tips
1
V1.0
305503001007
3
NVR Rear Panel
8
Software Operation
5
Placement of Wireless
IP Camera
1. Log In
2
NVR Kit Contents
8-Channel NVR
1.5m (5 ft) Ethernet Cable 4 x Bullet IP Cameras
USB Mouse Mounting Screws
For detailed manuals, tools, etc., please visit foscam.com/downloads.
4
Wireless Connectivity
WiFi Connection
Router
Computer HD-OUT Cable
TV
LAN
Ethernet Cable
LAN
LAN
HD-OUT
Monitor
VGA Cable
VGA
VGA
HD-OUT
Foscam
Do not install the wireless NVR in humid and dusty
environment.
Put the wireless NVR in drafty environment in case of
ventilation port being blocked.
Check the power supply to avoid damage because of voltage
mismatch.
Make sure the wireless NVR working within suitable
temperature and humidity environment.
Please install the wireless NVR horizontally, and avoid
vibration.
Short circuit may occur when dust become wet on circuit
board. Please clean the dust on circuit board, connectors, and
NVR case.
Explosion may happen because of improper replacement of
battery, do not replace it by yourself; If you need, make sure it
is the same type of battery. And do not open or repair it.
Please use suitable and professional hard disk to ensure
continues and stable recording.
Lightning protection is needed when device is connected to
communication cables. Ethernet cable which comes from
outside, connecting to the wireless NVR directly is forbidden.
Right placement Wrong placement
4 x Power Adapters for Cameras 1 x Power Adapter for NVR
Quick Setup Guide Warranty Card
2. Setup Wizard
The Setup Wizard can walk you through some important settings
on the NVR.
6
Camera Installation
Important Note:
When installing the cameras please ensure that the connection
ports at the end of the pig tail wiring are not exposed, as they
are not weather-resistant.
0~90°
0~360°
0~360°
0~90°
0~360°
0~360°
Place the cameras in your preferred locations and use the
included screws to mount them.
The shape of wireless NVR signal coverage is a ball, antenna is located in
the center. Signal is strong around antenna, and weak in the dent area of
the 2 antennas.
Based on the signal spreading ways, please make the wireless IP Camera
keeping parallel or tangent with wireless NVR, which ensure stable signal
transmission and better picture quality.
7
Powering Up
DC 12V/2A
Mouse
WiFi Connection
GND
Please make sure the voltage of power supply is matched
with wireless NVR, and ground connection work well in
socket. Connect the NVR and cameras as shown in the gures
above. Once the NVR is plugged in, press the power switch
located on the rear panel.
After the NVR starts up successfully, the Power LED indicators
will turn green, it means system runs smoothly.
DC 12V/1A DC 12V/1A DC 12V/1A DC 12V/1A
VGA
Monitor
VGA Cable
VGA
6
HD-OUT
VGA Output
USB
Antenna
Reset
Power Input
(DC12V / 2A)
Power Switch
Ethernet Port
GND
① Turn on the power switch on the rear panel.
After the NVR starts up successfully, the power LED and HDD
LED indicators will turn green. The startup page is displayed
on the screen.
② Change password .
For your security, please set a new password for your NVR
before Log In.
④ After modifying the password, you will be taken to the
Setup Wizard.
① Setting the time.
Uncheck the checkbox
② Format HDD. Click the button to set up the HDD. Format
Note that this will delete all les on the HDD.
HDD Full Setting Select Stop Record and Overwrite . .
③ P2P. If you want to know the UID of the device, please scan
the QR code. If you don’t want to use the Setup Wizard
next time, uncheck the Setup Wizard checkbox. Click the
Finish button to complete the setup wizard.
or Right-click uncheck →Main Menu →Conguration →
the checkbox. Click the button to Setup Wizard Finish
complete the setup wizard.
Uncheck the checkbox
The live view interface will show you the video feed of each IP
Camera.
3. NVR adds IP Camera method
Note: The NVR and IP Camera are already paired. If you need to
match more cameras, please refer to the following steps.
F19911W is supported in this kit, besides the battery camera the
other Foscam models can be added by LAN.
① Right-click on main interface, select Pair IP Camera.
② Click and press the pairing button of the camera tail cablePair
at the same time, until it prompts that the pairing is successful.
③ When nished code matching, The live view interface will
show you the video feed of each IP Camera.
1. Click Pair
4. Record and Playback
① → → → Scheduled Record: Right-click Main Menu Record
choose recording channel (Actually, the Wi-Fi NVR →Save
system have default set 24h scheduled recording).
③ Login page.
Enter the Username and Password, then click on the OK
button.
If you want to modify it to alarm recording, please use the left
mouse button to select the time (turned to green), if the other
channels operate in the same way, select .copy
press the
pairing button
Add F19911W:
Add Other Foscam Camera:
① Right-click on main interface, select Channel cong.
② Click and then click .Add IPC Search Add
③ Select the Camera to be added.
④ Click and enter the username and password for the Add
camera, then click on the .Save
⑤ When nished added, the live view interface will show you
the video feed of each IP Camera.
1. Click Add IPC
2. Click Search Add
4. Click Add
3. Select the camera
to be added
13 14 15 1716
19 20 21 22
18
23 24
Technical Support
13
If you have problems with your Foscam device, please contact
the reseller you purchased from, or you can e-mail the
headquarters technical support team: support@foscam.com
Your valuable comments and suggestions on improving
Foscam products are welcomed!
9
Foscam App
2. Run the APP, and then register for a Foscam
Foscam account.
CE Certificate statement Website:
https://www.foscam.com/company/ce-certificate.html
Exporter and Importer Information Opened to Public:
https://www.foscam.com/company/open-information.html
www.foscam.com
Due to product upgrades and other reasons, this guide may be slow to
update, resulting in slight inconsistencies with the ocial website
information. Please take the ocial website(www.foscam.com)
information as the current standard.
11
Upgrade
1. You can upgrade your NVR and cameras system with local
Software.
Note:
① The upgrade le must be placed under the root directory of
the U disk.
② Don't lose power for during upgrade.
4. Preview: click device in list to enter preview interface,
select a channel to view it’s picture, as follow shows:
1. You can also simply go to the App Store or Google Play and
search for the term " ". Download the APP to yourFoscam
Manufacturer: Shenzhen Foscam Intelligent Technology Co., Ltd
Addr: Room 901-902,Building 1B, Shenzhen International Innovation
Valley, Xingke 1st Street, Nanshan District, Shenzhen, Guangdong,
China, 518055
WLAN frequency range: 2400 MHz - 2483.5 Mhz.
Maximum transmission power: < 20dBm
Wireless Standard: IEEE802.11b/g/n
Power Supply: DC 12V 2.0A 24W (NVR)
DC 12V 1.0A 12W (IPC)
NVR Upgrade:
Download the rmware to the U disk Insert U disk to NVR →
USB port Right-click click→ → Main Menu →Upgrade →
Refresh Upgrade → click to upgrade your NVR.
IPC Upgrade:
Download the rmware to the U disk Insert U disk to NVR USB →
port Right-click → → Main Menu →IPC Cong Maintenance→
→ → click Refresh click to update this camera or click CH Select
All to upgrade your all cameras.
IPC Restore default:
Right-click →Main Menu →IPC Cong Maintenance→ →
click to restore default this camera or click to CH Select All
restore default your all cameras.
Note:
Don't shut down the power during upgrade. After upgrading,
NVR restarts.
Product Performance
12
3. Device Adding: Once logged in, you can tap the "+" button
on the APP, after that scan the QR code, which is located
at the bottom of your NVR.
10
Foscam VMS
Foscam VMS is a new tool for PC. It does not require plug-ins and
is compatible with Windows & Mac, It supports all Foscam HD
cameras and up to 36 cameras at the same time. If you would
like to manage multiple cameras, we suggest you install the
Foscam VMS. You can download the “Foscam VMS” from
foscam.com/vms, and can download the "Foscam VMS" Mac
version from the APP store:
https://apps.apple.com/cn/app/foscamvms/id1521202507?mt=12
Add the NVR
1. Run Foscam VMS, then you can create a local administrator
account and login.
2. Tap the "+" button on the Foscam VMS and follow the setup
wizard to add your NVR.
Please refer to the user manual for more detailed adding steps.
3. Preview: click device in Lan Device list to enter preview
interface, select a channel to view it’s picture, click to
enter , as follow shows:
2. You can upgrade the rmware of your NVR and cameras with
Foscam App.
Open Foscam APP and Login the NVR, select Settings > NVR
Firmware Camera Firmware or Upgrade.
3. You can upgrade the rmware of your NVR and cameras with
Foscam VMS.
Open and Login Foscam VMS, select Setup > > System
System Upgrade Camera Upgrade or .
Note:
In all upgrade methods, don't shut down the power during
upgrade. After upgrading, NVR restarts.
6. Motion Detection Record
Right-click → Main Menu →IPC Cong Advanced → →
Motion Detect Enable Choose → → Set Sensitivity & Region &
Body Filter & Body Rectangle . →Apply
7. Auto Bridge
By new mesh network auto-bridging function, without any
manual setting, wireless camera in further area will have a
judgment about the WIFI signal and auto connect to the
camera which have a better WIFI signal, to achieve more stable
and reliable video transmission.
Auto bridging is designed to expand the coverage area of
wireless signal, instead of enhancing the signal. When camera is
a little far away from NVR, or there are too many interference
factors/sources between them, camera in further area will auto
bridge/connect to the one nearby to transmit the video data.
① → → Right click Pair IP Camera Repeater.
② Then, bridging relationship will be showed on the interface
automatically.
1.Click the button to select
the rmware to the U disk
2.Click the button to
Upgrade
1.Click the button to select
the rmware to the U disk
2.Choose the channel camera
you need to upgrade
3. Click the button to
Upgrade
1.Choose the channel camera
you need to Restore
2. Click the button to
Restore
Note: For the best experience, please update Foscam VMS to the
latest version!
Firmware upgrade step:
① Click " " button to downloadDownload the latest rmware
the latest rmware to your computer.
② Click " " button , choose le rmware version youBrowse
want to upgrade on the web page.
③ Click " " button and wait till it's nished.Upgrade
1
Basic
Device Manager
Application
System
Factory Reset
Camera Firmware
Reboot
NVR Firmware
Current firmware version 2.71.1.79：
Download the latest firmware
2
Browse
Device Settings
Upgrade 3
FN7108W
FN8108H
smartphone, or scan the QR Code on the below, it will take
you to the download page to install the . Foscam APP
② → → → Playback: Right-click Main Menu Playback choose
channel and date click timeline to check record.→
5. Backup
Insert U disk to NVR USB port Right-click → → Main Menu →
Backup Search → → choose channel, type and time select →
target le →Backup
Note: EmptyIf target le can not be searched out, please click →
Add. Please remove the les which is no need before backup.
Ensure insert device (like USB) in 30 second, as system reserved
searching time for it is 30 second.

Specyfikacje produktu

Marka: Foscam
Kategoria: nieskategoryzowany
Model: FN8108W-B4

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Foscam FN8108W-B4, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje nieskategoryzowany Foscam

Foscam

Foscam FNA108H Instrukcja

24 Września 2024
Foscam

Foscam FN9108E-B4 Instrukcja

24 Września 2024
Foscam

Foscam FN9108H Instrukcja

24 Września 2024
Foscam

Foscam FNA108HE Instrukcja

24 Września 2024
Foscam

Foscam FN9108HE Instrukcja

24 Września 2024
Foscam

Foscam T5EP Instrukcja

24 Września 2024
Foscam

Foscam T8EP Instrukcja

24 Września 2024
Foscam

Foscam FN7104W-B4 Instrukcja

24 Września 2024
Foscam

Foscam FN8108W-B4 Instrukcja

22 Sierpnia 2024

Instrukcje nieskategoryzowany

Najnowsze instrukcje dla nieskategoryzowany

Asko

Asko DBI644MIB.S.TW/1 Instrukcja

28 Października 2024
Asko

Asko DFS233IB.S.TW/1 Instrukcja

28 Października 2024
Emko

Emko EZM-9920 Instrukcja

27 Października 2024
Emko

Emko ESM-3712-H Instrukcja

27 Października 2024
Emko

Emko ATS-10 Instrukcja

27 Października 2024
Emko

Emko EAOM-11.2 Instrukcja

27 Października 2024
Emko

Emko EPM-3790 Instrukcja

27 Października 2024
Emko

Emko EPM-7790 Instrukcja

27 Października 2024
Livarno Lux

Livarno Lux IAN 108340 Instrukcja

27 Października 2024
Livarno Lux

Livarno Lux HG06009A-BS Instrukcja

27 Października 2024