Instrukcja obsługi Fortin EVO-ONE

Fortin Zdalne sterowanie EVO-ONE

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Fortin EVO-ONE (18 stron) w kategorii Zdalne sterowanie. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/18

ALL-IN-ONE DATA INTERFACE

REMOTE STARTER / ALARM

QUICK

INSTALLATION GUIDE

D C B HIJ

(6-PIN) BYPASS RELAY

(5-PIN) CAN-BUS (4-PIN) RS-232 DATA-LINK & FLASH-LINK UPDATER PORT

BYPASS PROGRAMMING BUTTON

REMOTE STARTER PROGRAMMING LED

CUT LOOP FOR

AUTOMATIC

TRANSMISSION

MODE.

Red White Blue Blue Black

LED Blue CAN ACTIVITY

LED Yellow IGNITION ON

LED Red BYPASS DATA

(+) Foot Brake Black In

750mA (-) Parking lights Pink Out

750mA (-) Trunk Release / AUX Yellow/Black Out

(-) Hand Brake Brown/White In

(-) Hood/Door Pink/Black In

%\SDVVFRQ¿J Purple/Yellow

%\SDVVFRQ¿J Green/White

%\SDVVFRQ¿J Green/Red

%\SDVVFRQ¿J White/Black Out

%\SDVVFRQ¿J /W%OXH

Ground Black In

(+) Ignition Pink Out

(+) Starter Yellow Out

Out White

(+) ParkLight/IGN2

/ACC/START

3URJUDPPDEOH2XWSXW

(FUNCTION 2 & 31)

Out 2UDQJH

(+) ACC / IGN2

3URJUDPPDEOH2XWSXW

(FUNCTION 2 & 31)

In Red (+) 12V

In Yellow (+) Bypass Ignition

Out Purple (-) Lock 750mA

Out Purple/White (-) Unlock 750mA

Out Green (-) Ignition 750mA

Out White (-) Start 750mA

Out 2UDQJH (-) Disarm 750mA

Out 2UDQJH%ODFN (-) Horn/Siren 2 Amp

Out 'N%OXH (-) GWR / Programmable 750mA

In Red/Blue %\SDVVFRQ¿J

/W%OXH%ODFN %\SDVVFRQ¿J

750 mA MAXIMUM OUTPUT. Do not exceed the maximum current or permanent damage to the module

will occur that will not be covered under warranty.

(6-PIN) POWER CONNECTOR

(20-PIN) SECONDARY CONNECTOR

(3-PIN) Shock Sensor

(2-PIN) Valet/Programming Button

A20

WIRING / CONNECTION GUIDE

PROGRAMMING REMOTE TRANSMITTER(S)

Black

White

(4-PIN) ANTENNA(4-PIN) DATA-LINK ANTENNA

REMOTE

STARTER

FIRMWARE

VERSION

1. [21]

ET PLUS

The system can learn up to a maxi-

mum of 4 transmitters.

Any transmitters can be stored in

more than 1 memory slot.

When a 5th transmitter is learned

the 1st remote is erased (FIFO).

STEP 1 STEP 2 STEP 3 STEP 4 STEP 5 STEP 6

WITH IGNITION SWITCH

Turn the Ignition

OFF.

Turn the

Ignition ON.

The LED will

turn ON

Press and

release the

brake pedal

four times.

Turn the

Ignition

ON.

WITH VALET SWITCH

Press and hold

the valet switch

until the park-

ing lights turn

ON, the horn/

siren will chirp. x5

Press and release the valet switch

ve time.

The parking lights will ash and the

horn/siren will chirp each time to

conrm. x1

Press and re-

lease the brake

pedal once.

The LED

will ash

rapidly.

On each Transmitter press

and release the button

then press and release the

button. The LED will stop

ashing conrming programming.

Turn the Ignition

OFF to exit

programming.

1 32 4

EVO-ONEEVO-ONE

DOWNLOAD THE SPECIFIC VEHICLE INSTALLATION

GUIDE GUIDE, USER OR THE LATEST QUICK

INSTALLATION GUIDE AT:

WWW.FORTIN.CA

RF642W

GUIDE # 33021

FUNCTION

FUNCTION MODE 1 MODE 2 MODE 3 MODE 4 MODE 5 MODE 6

1 — — — — — — —

Programmable Output

(+) Ign/Acc/Start

(FUNCTION 31

MODE 4)

White (+)Ignition2 White (+)Accessory2 White (+)Start2 White (+)Start

— —

Orange (+)Accessory Orange (+)Accessory Orange (+)Accessory Orange (+)Ignition2

Pink (+)Ignition Pink (+)Ignition Pink (+)Ignition Pink (+)Ignition

Yellow (+)Start Yellow (+)Start Yellow (+)Start Yellow (+)Start2

3 Tachless sensivity Increase

crank time (By default)

Decrease

crank

time

4Remote car starter

runtime

Gas: 15 minutes

Diesel: 30 minutes

Gas: 7 minutes

Diesel: 14 minutes

Gas: 3 minutes

Diesel: 6 minutes — — —

5Add Remote on FMH

antenna series Add Remote — — — — —

6 Doorlock option No Unlock before remote-start &

Lock after remote-start. Lock after remote-start. Unlock and relock after

shut-down.

Relock 10 sec.after

shut-down.

Disarm before

shut down.

7Ignition Doorlock

option No

Lock after foot-brake &

unlock after key is turned

OFF.

Unlock after key is turned

OFF.

Doorlock Output at

Ignition only. — —

8 Unlock Pulse Time Single 0.25 sec Double 0.25 sec Single 4.0 sec Single 2.5 sec Single 1.5 sec Single 0.75 sec

9Active or Passive

Alarm & Starter Kill.

Active

Press LOCK to activate

the Alarm and starter-kill.

Passive (Lock disabled)

Arm alarm activate

starter-kill 30(MODE

4), 60(MODE5), or

120(MODE6) sec. after the

door is closed.

Passive (Lock enabled)

Arm alarm, activate

starter-kill and lock doors

30(MODE 4), 60(MODE5),

or 120(MODE6) sec. after

the door is closed.

Passive arm

30 seconds (by default

if MODE 2 ot 3 is

activated.

Passive arm

60 seconds. (if

MODE 2 ot 3 is

activated.

Passive arm

120 seconds.

(if MODE 2 ot 3

is activated.

Starter Kill Output.

Required function 32

mode 4. - Dk.Blue

(A8) = starter-kill.

Starter-kill &anti-grind Anti-grind only Relay normally open — — —

Sound Con rmation

& LED antenna

Antidémarreur

1st LOCK/UNLOCK silent

2nd LOCK/UNLOCK

sound

---------------------------

Antenna LED active.

LOCK/UNLOCK

sound always. Antenna LED disabled. Antenna LED disabled

with ignition.

Con rmation sound

at LOCK only

Panic mode

disabled

12 Output horn/siren

con guration Horn(-) only. Siren(+) Output (E1) white Siren(+) Output (E1) white

and Horn(-) Siren(-) only (A7) — —

13 Con rmation Pulse Long Short — — — —

14 Alarm ON/OFF

Starter ON/OFF

Alarm OFF

Remote-starter ON

Alarm ON

Remote-starter ON.

Alarm ON

Remote-starter OFF — — —

Smart Arming

Smart Doorlock

Smart Lock pulse

Disable

(Unlock signal) Automatically

LOCK and rearm alarm if

door(s) are not opened after

30 seconds.

Automatic Lock when

starter kill arms.

Lock pulse only when its

Unlock — —

16 Cold Start Timer 3 hours at -5 oc/Runtime 1.5 hours at -5oc/Runtime 3 hours at -5oc/5 minutes 1.5 hours at -5oc/5

minutes Cold time OFF —

17 — — — — — — —

18 Diesel Mode Disable

Enable (20 seconds)

Delay between Ignition

power up and Starter (crank).

Enable (10 seconds)

Delay between Ignition

power up and Starter

(crank).

Enable

No delay between

Ignition power up and

Starter (crank).

— —

19 Turbo timer Disable Run 2 minutes. Run 4 minutes. — — —

Engine supervision:

-Tachless -

-analog tach-

-Tach Data-Link-

Tachless on crank

and supervision Tach

Data-Link.

Tachless only.

( vehicles with automatic

transmission only)

—

Start (crank) 8 seconds

on Tachless.

( vehicles with

automatic transmission

only)

Start (Crank) 8 sec

+ Supervision by

Data-LInk Tach

Tach Data-Link

only

STEP STEP STEP STEP STEP STEP 1 2 3 4 5 6

Disarm

the

system

(The

antenna

led must

not be

 ashing,

see enter/

exit valet

mode

p.4).

FM H

FMH

2-W

MODE 1 - LOCK

MODE 2 - UNLOCK

MODE 3 - START (3 SECONDS)

MODE 4 - FUNCTION (3 SECONDS)

MODE 5 - FUNCTION LOCK

MODE 6 - FUNCTION UNLOCK

Turn the

Ignition

ON.

Press and

hold the valet

switch or the

antenna but-

ton until the

Parking lights

turn ON, the

horn/siren will

chirp.

The

LED will

 a s h

rapidly.

Press and release the valet

switch or the antenna but-

ton X time for the desired

function. The Parking

lights will  ash and the

horn/siren will chirp each

time to con rm.

Press and

release the

brake-ped-

al once.

Turn the Igni-

tion OFF to

exit program-

ming.

The Parking

lights will

 ash 4

times.

Press the BUTTON on a programmed remote to select the mode (X).

The Parking lights will  ash 1-6 times to con rm.

Return to step 3 to programmed the next option

FMH

2-W

FUNCTION PROGRAMMING

FUNCTION MODE 1 MODE 2 MODE 3 MODE 4 MODE 5 MODE 6

21 Start Attempts 2 1 3 — — —

22 — — — — — — —

23 Master RESET

RESET all programming

options by default.

(Retains already

programmed remote.)

— — — — —

24 — — — — — — —

25 Yellow/Black (A13) :

Aux1 --> LOCK

0.5 seconds &

disarm alarm 0.5 seconds 10 sec latch or

until a button is pressed.

20 sec latch or

until a button is pressed.

30 sec latch or

until a button is

pressed.

Latch until

shutdown

26 Hybrid mode Gas / Diesel vehicle Hybrid vehicle — — — —

27 — — — — — — —

28 — — — — — — —

29 Alarm Duration 30 seconds 60 seconds 120 seconds — — —

30 Valet code Ignition ON

Valet button p3-x3 times.

Ignition ON

Valet button p3-x3 times

and p3-x1 times 3 seconds.

Ignition ON

Valet button p3-x4 times

and p3-x1 times 3 seconds.

Ignition ON

Valet button p3-x5 times

and p3-x1 times 3 seconds.

Ignition ON

Valet button p3-x6

times and p3-x1 times

3 seconds.

Ignition ON

Valet button p3-x7

times and p3-x1

times 3 sec.

Special application

Programmable output

(+)

No special application

Priority on function 2

Special application - Function 2 (all option)

not available.

White (+) Parking

Light White

(+)

Parking

Light

White:

(+) Parking

Lights

Orange (+)

Accessory Orange Ign.2

Orange:

(+) Parking

lights

White wire (E1) : Enable

at ground out, disable with

vehicle ignition OFF.

White wire (E1) : Trunk

Output Pink (+) Ignition Pink Ign.1 Pink:

(+) Ignition

Yellow (+) Start Yellow (+) Start Yellow:

(+) Start

32 Ground Out

Dk.Blue (Ground out):

Shut-down 1 second after

remote start run time.

Dk.Blue (Ground out):

Shut-down 3 seconds after

remote start run time.

Dk.Blue

(Ground Out):

Shutdown After

D.k Blue

(Ground Out):

Starter-Kill

D.k Blue

(Ground Out):

Arm / Rearm

Controlled by

CAN learning

33 Manual transmission

function

Manual transmission

completed by door closed.

Automatically activated by

hand-brake and Foot Brake

Manual sequence

completed by locking the

doors

Cancel ready mode when

trunk open. — —

34 Trunk output Pulse 0.5 seconds Pulse 2.5 seconds Unlock before trunk pulse

0.5sec

Trunk Output at ignition

only — —

35 Door unlock Special

application No special application Activate vehicle ignition at

unlock.

Activate vehicle ignition

and accessory at unlock. — — —

Activation/

desactivation remote

Valet Mode

—

by remote :

FUNCTION --> LOCK +

UNLOCK or valet button

By Valet button only — — —

Security Remote car

starter

Special application

No special application

Security ON: Shutdown

Engine if the door is opened

before UNLOCK is pressed.

(Door trigger required).

— — — —

38 System control by

OEM Remote Disable Press 3x Lock to remote start Start/Stop on trigger shock

sensor

Alarm control by OEM

Remote.

Press Lock, Unlock

Lock to remote start —

39 Temperature option Disable

Enable : AUX1 activated at

oc when remote started (see

function 25)

— — — —

LEGEND: FUNCTION BY DEFAULT

FUNCTION

RESETS ALL FUNCTIONS BACK TO DEFAULT AND ERASES ANY REMOTES THAT HAVE BEEN PROGRAMMED.

Disarm the

system (The

antenna led

must not be

ashing, see

enter/exit

valet mode

p.4).

STEP 1 STEP 2 STEP 3 STEP 4 STEP 5 STEP 6

Turn the

Ignition

ON.

Press and hold the

valet switch or the

antenna button until

the Parking lights

turn ON, the horn/

siren will chirp.

Press and

release the

valet switch

or the antenna

button

23 times.

X1 Press and

release

the brake-

pedal

once.

OR Press and hold

the valet switch

or the antenna

button for 5 sec-

onds. The Parking

lights will ash to

conrm.

Turn the Igni-

tion OFF to

exit program-

ming. The

Parking lights

will ash 4

times.

FM H

2-W

FM H

2-W

FM H

2-W

Specyfikacje produktu

Marka:	Fortin
Kategoria:	Zdalne sterowanie
Model:	EVO-ONE

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Fortin EVO-ONE, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Zdalne sterowanie Fortin

Fortin EVO-ALL Instrukcja

17 Września 2024

Fortin EVO-ONE Instrukcja

17 Sierpnia 2024

Fortin EVO-GMT6 Instrukcja

17 Sierpnia 2024

Instrukcje Zdalne sterowanie

Najnowsze instrukcje dla Zdalne sterowanie

Neewer RT112 Instrukcja

9 Października 2024

Neewer RT113 Instrukcja

9 Października 2024

Zalman ZM-VE350 Instrukcja

9 Października 2024

Canon BG-R20 Instrukcja

9 Października 2024

Canon BG-R20EP Instrukcja

9 Października 2024

Mosconi DSP6T8 Instrukcja

8 Października 2024

Mosconi RC MINI Instrukcja

8 Października 2024

Ridem CRC UNB Instrukcja

8 Października 2024

Ridem CRC UNW Instrukcja

8 Października 2024

ORNO OR-GB-458 Instrukcja

8 Października 2024