Instrukcja obsługi Focusrite ISA 215


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Focusrite ISA 215 (1 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/1
ISA 215
Dual Channel Mic-pre and Equaliser
The controls on this module are identical for both channels and are described from left to right along the
front panel .
Mains Power Switch - this is a mini rocker switch . When switched on , two LEDs indicate correct
operation of the bipolar 15volt power rails .
Phase Invert Switch - A latching , illuminated push switch which inverts the phase of the input signal by
180°
Overload Indicator - illuminates when the peak of the signal level reaches or exceeds +20dB , which is
6dB prior to the onset of clipping.
High Pass Filter - Frequency selection is by a six way rotary switch with the highest position switching
the filter out .
Low Pass Filter - Situated to the right of the High Pass Filter , frequency selection is again by a six way
rotary switch with the highest position switching the filter out . Both filters have a rolloff of -18dB /
octave and their operation is independent of the All EQ In switch .
All Eq In switch - An illuminated , latching push switch situated at the bottom left of the Low
Frequency Shelving section . This is a master EQ switch which inserts the EQ circuitry into the signal
path . This switch must be engaged to enable operation of the other EQ In switches .
Low and High Frequency Shelving Stages - The Eq In switch , an illuminated , latching push switch
inserts the two equaliser stages into the signal path . This switch only operates when the All EQ In
switch is engaged .
The controls for these two sections are identical , except for the frequency range of the stages. Each
stage has a continuously variable boost and cut control with centre detent providing up to 16dB cut or
boost . Each stage has a six way rotary switch for frequency selection with six frequencies available for
each .
Low Mid and High Mid Frequency Parametric Stages - The Eq In switch , an illuminated , latching push
switch inserts the two equaliser stages into the signal path . Again this switch only operates when the All
EQ In switch is engaged .
The controls for these two sections are identical , except for the frequency range of the stages. Each
stage has a continuously variable boost and cut control with centre detent providing up to 16dB cut or
boost .
There is a frequency sweep control with two ranges, the higher range being available when the x 3
switch is engaged . Last but not least is a variable Q or bandwidth control.
Line Input - Selected when the momentary push switch “Line” is illuminated . A seven way rotary
switch selects the Line Input sensitivity , ranging from -18dB to +18dB in 6dB steps
Mic Input - Selected when the momentary push switch “Mic” is illuminated . An eleven way rotary
switch selects the Mic Input sensitivity , ranging from -60dB to 0dB in 6dB steps .
+48v - An illuminated , latching push switch providing phantom power to the Mic input XLR
Trim - A continuously variable control providing up to 12dB of gain trim which can be applied to either
Line or Mic input .


Specyfikacje produktu

Marka: Focusrite
Kategoria: Niesklasyfikowane
Model: ISA 215

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Focusrite ISA 215, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Niesklasyfikowane Focusrite

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024