Instrukcja obsługi First Alert SA340

First Alert Detektor dymu SA340

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla First Alert SA340 (6 stron) w kategorii Detektor dymu. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/6

USER’S MANUAL

Printed in Mexico

M08-0143-002 05/07J1

INTRODUCTION

Thank you for choosing First Alert

®for your Smoke Alarm needs. You

have purchased a state-of-the-art Smoke Alarm designed to provide

you with early warning of a fire. Please take the time to read this manual

and make the Smoke Alarm an integral part of your family’s safety plan.

Key Features of the SA340 Smoke Alarm:

Tamper Resistant Lithium Powercell: Provides continuous power for

up to 10 years. Powercell cannot be removed.

Single Test/Silence Button: Allows you to test the Alarm or silence

nuisance alarms. Testing the Alarm assures you that the unit is function-

ing correctly and ready to protect you and your family. The Alarm can

be silenced for up to 10 minutes in the event of a nuisance alarm.

Low power warning: The Alarm will sound a “chirp” once per minute

when the Alarm reaches the end of its service life and needs to be

replaced.

Blinking Power Indicator: Confirms that the Smoke Alarm is receiving

power.

3901 Liberty Street Road, Aurora, IL 60504-8122

FIRE SAFETY TIPS

Follow safety rules and prevent hazardous situations: 1) Use smoking

materials properly. Never smoke in bed. 2) Keep matches or lighters

away from children; 3) Store flammable materials in proper containers;

4) Keep electrical appliances in good condition and don’t overload elec-

trical circuits; 5) Keep stoves, barbecue grills, fireplaces and chimneys

grease- and debris-free; 6) Never leave anything cooking on the stove

unattended; 7) Keep portable heaters and open flames, like candles,

away from flammable materials; 8) Don’t let rubbish accumulate.

Keep alarms clean, and test them weekly. Replace alarms immediately if

they are not working properly. Smoke Alarms that do not work cannot alert

you to a fire. Keep at least one working fire extinguisher on every floor, and

an additional one in the kitchen. Have fire escape ladders or other reliable

means of escape from an upper floor in case stairs are blocked.

BEFORE YOU INSTALL THIS SMOKE ALARM

IMPORTANT! Read “Recommended Locations for Smoke Alarms”

and “Locations to Avoid for Smoke Alarms” before beginning. This

unit monitors the air, and when smoke reaches its sensing chamber,

it alarms. It can give you more time to escape before fire spreads.

This unit can ONLY give an early warning of developing fires if it is

installed, maintained and located where smoke can reach it, and where

all residents can hear it, as described in this manual. This unit will not

sense gas, heat, or flame. It cannot prevent or extinguish fires.

Understand The Different Type of Smoke Alarms

Battery powered or electrical? Different Smoke Alarms provide

different types of protection. See “About Smoke Alarms” for details.

Know Where To Install Your Smoke Alarms

Fire Safety Professionals recommend at least one Smoke Alarm on

every level of your home, in every bedroom, and in every bedroom

hallway or separate sleeping area. See “Recommended Locations

For Smoke Alarms” and “Locations To Avoid For Smoke Alarms” for

details.

Know What Smoke Alarms Can and Can’t Do

A Smoke Alarm can help alert you to fire, giving you precious time

to escape. It can only sound an alarm once smoke reaches the

sensor. See “Limitations of Smoke Alarms” for details.

Check Your Local Building Codes

This Smoke Alarm is designed to be used in a typical single-family

home. It alone will not meet requirements for boarding houses,

apartment buildings, hotels or motels. See “Special Compliance

Considerations” for details.

All First Alert®Smoke Alarms conform to regulatory requirements,

including UL217 and are designed to detect particles of combustion.

Smoke particles of varying number and size are produced in all fires.

Ionization technology is generally more sensitive than photoelectric

technology at detecting small particles, which tend to be produced

in greater amounts by flaming fires, which consume combustible

materials rapidly and spread quickly. Sources of these fires may include

paper burning in a wastebasket, or a grease fire in the kitchen.

Photoelectric technology is generally more sensitive than ionization

technology at detecting large particles, which tend to be pro-

duced in greater amounts by smoldering fires, which may smolder

for hours before bursting into flame. Sources of these fires may include

cigarettes burning in couches or bedding.

For maximum protection, use both types of Smoke Alarms on each

level and in every bedroom of your home.

• This unit will not alert hearing impaired residents. It is recom-

mended that you install special units which use devices like

flashing strobe lights to alert the hearing impaired residents.

• Do not connect this unit to any other alarm or auxiliary device.

It is a single-station unit that cannot be linked to other devices.

Connecting anything else to this unit may prevent it from working

properly.

• This Smoke Alarm cannot detect smoke until you activate it.

You must activate the unit for it to receive power from the

powercell. Failure to activate the unit will prevent the alarm

from providing any warning of smoke or fire.

• The powercell in this unit cannot be replaced—once it reaches

the end of its service life, you must install a new Smoke Alarm.

You must deactivate the unit before disposing of it.

• Do not install this unit over an electrical junction box. Air currents

around junction boxes can prevent smoke from reaching the

sensing chamber and prevent the unit from alarming. Only AC

powered units are intended for installation over junction boxes.

• Do not stand too close to the unit when the alarm is sounding.

It is loud to wake you in an emergency. Exposure to the horn at

close range may harm your hearing.

• Do not paint over the unit. Paint may clog the openings to the

sensing chamber and prevent the unit from operating properly.

SMOKE ALARM WITH TEN-YEAR

NON-REPLACEABLE LITHIUM POWERCELL

Model SA340

IMPORTANT! PLEASE READ

CAREFULLY AND SAVE.

This user’s manual contains

important information about

your Smoke Alarm’s operation.

If you are installing this Smoke

Alarm for use by others, you

must leave this manual—or a

copy of it—with the end user.

Model SA340

TABLE OF CONTENTS

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Fire Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Before You Install This Smoke Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

How to Install This Smoke Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Weekly Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

If This Smoke Alarm Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

If You Suspect a Problem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Recommended Locations for Smoke Alarms . . . . . . . . . . . . . . . . . . . . 4-5

Locations to Avoid for Smoke Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

About Smoke Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Special Compliance Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Limitations of Smoke Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Regular Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

HOW TO INSTALL THIS SMOKE ALARM

THE PARTS OF THIS SMOKE ALARM

FOLLOW THESE SIMPLE STEPS!

INSTALL THE MOUNTING BRACKET:

1. To remove the mounting bracket from the

Smoke Alarm base, hold the Smoke Alarm

base firmly and twist the mounting bracket

counterclockwise.

2. Place the bracket on the wall or ceiling where

you want to mount the alarm.

3. Hold the mounting bracket against the ceiling

(or wall) and trace around the inside of the two

keyhole slots.

4. Make a mark inside each outline for the drill holes.

5. Put the unit where it won’t get covered with dust when you drill

the mounting holes.

6. Using a 3/16-inch (5 mm) drill bit, drill a hole through each

pencil mark.

7. Insert the plastic screw anchors (in the plastic bag with screws)

into the holes. Tap the screw anchors gently with a hammer, if

necessary, until they are flush with the ceiling or wall.

8. Line the mounting bracket up over the plastic screw anchors.

9. Screw the mounting bracket to the ceiling or wall through the

mounting slots using the two screws provided.

10. Tighten both screws all the way.

1. Test/Silence button

2. Power/alarm indicator LED

1. Mounting bracket

2. Mounting slots

3. Powercell

4. Deactivation Tab (located under label)

5. Turn to attach to bracket

6. Turn this way to remove from bracket

INSERTING THE POWERCELL:

You must activate the powercell before attaching the Smoke

Alarm to the bracket.

1. Turn Alarm upside down. Line up

the pins and snap the powercell

into the Alarm.

2. The powercell cannot be removed

after it is locked into the Alarm.

If you have trouble activating the

unit, call Consumer Affairs at:

1-800-323-9005 for assistance.

3. Test the Smoke Alarm. Press and hold the test button on the

cover of the unit until the alarm sounds (the unit may continue

to alarm for a few seconds after you release the button).

During testing, you will hear a loud, repeating horn pattern:

3 beeps, pause, 3 beeps, pause. If the unit does not alarm

during testing, call Consumer Affairs for assistance.

ATTACH SMOKE ALARM TO MOUNTING BRACKET

1. Line up the alignment tab on the unit with the alignment tab on

the mounting bracket. Push the unit toward the bracket, and

turn it clockwise until you feel it snap into place.

2. Test the unit again. Press the test button until the horn begins

sounding. During testing, you will hear a loud, repeating

horn pattern: 3 beeps, pause, 3 beeps, pause.

TOOLS YOU WILL NEED:

This unit is designed to be mounted on the ceiling,

or on the wall if necessary.

• Pencil

• Drill with 3/16” (5 mm)

drill bit

• Standard flathead

screwdriver

• Hammer

WEEKLY TESTING

• NEVER use an open flame of any kind to test this unit. You

might accidentally damage or set fire to the unit or to your

home. The built-in test switch accurately tests the unit’s

operation as required by Underwriters Laboratories, Inc. (UL).

• If the Alarm ever fails to test properly, replace it immediately.

Products under warranty may be returned to the manufacturer

for

replacement. See “Limited Warranty”.

DO NOT stand close to the Alarm when the horn is sounding.

Exposure at close range may be harmful to your hearing. When

testing, step away when horn starts sounding.

It is important to test this unit every week to make sure it is working

properly.

Using the test button is the recommended way to test this

Smoke Alarm. Press and hold the test button on the cover of the unit

until the alarm sounds (the unit may continue to alarm for a few seconds

after you release the button). During testing you will hear a loud,

repeating horn pattern: 3 beeps, pause, 3 beeps, pause. Red LED

flashes.

IF THIS SMOKE ALARM SOUNDS

RESPONDING TO AN ALARM

During an alarm, you will hear a loud, repeating horn pattern:

3 beeps, pause, 3 beeps, pause. Red LED flashes.

• If the unit alarms get everyone out of the house immediately.

• If the unit alarms and you are not testing the unit, it is warning

you of a potentially dangerous situation that requires your

immediate attention. NEVER ignore any alarm. Ignoring the

alarm may result in injury or death.

• Use the Silence feature to stop an unwanted alarm (caused by

cooking smoke, etc.), then open a window or fan the smoke

away from the unit. The Smoke Alarm will reset automatically.

WHAT TO DO IN CASE OF FIRE

• Don’t panic; stay calm. Follow your family escape plan.

• Get out of the house as quickly as possible. Don’t stop to

get dressed or collect anything.

• Feel doors with the back of your hand before opening them.

If a door is cool, open it slowly. Don’t open a hot door. Keep doors

and windows closed, unless you must escape through them.

• Cover your nose and mouth with a cloth (preferably damp).

Take short, shallow breaths.

• Meet at your planned meeting place outside your home,

and do a head count to make sure everybody got out safely.

• Call the Fire Department as soon as possible from outside.

Give your address, then your name.

• Never go back inside a burning building for any reason.

• Contact your Fire Department for ideas on making your home safer.

Alarms have various limitations. See "Limitations of Smoke Alarms"

for details.

USING THE SILENCE FEATURE

The Silence Feature can temporarily quiet an unwanted alarm for up

to 10 minutes. To use this feature, press the “Test/Silence” button. The

Alarm remains functional. The LED will flash every 10 seconds (for up

to 10 minutes) to remind you the alarm has been silenced. The flashing

LED will stop when the unit returns to normal operation.

The Silence Feature does not disable the unit—it makes it temporar-

ily less sensitive to smoke. For your safety, if smoke around the unit

is dense enough to suggest a potentially dangerous situation, it

will stay in alarm, or may re-alarm quickly. If you do not know the

source of the smoke, do not assume it is an unwanted alarm. Not

responding to an alarm can result in property loss, injury or death.

REGULAR MAINTENANCE

This unit has been designed to be as maintenance free as possible, but

there are a few simple things you must do to keep it working properly.

• Test it at least once a week.

• Clean the Smoke Alarm at least once a month; gently vacuum the

outside of the Smoke Alarm using your household vacuum’s soft

brush attachment. A can of clean compressed air (sold at computer

or office supply stores) may also be used. Follow manufacturer

instructions for use. Test the Smoke Alarm. Never use water,

cleaners or solvents since they may damage the unit.

• If the Smoke Alarm becomes contaminated by excessive dirt, dust

and/or grime, and cannot be cleaned to avoid unwanted alarms,

replace the unit immediately.

• Relocate the unit if it sounds frequent unwanted alarms. See

“Locations to Avoid For Smoke Alarms” for details.

When the powercell becomes weak, the Smoke Alarm unit will “chirp”

about once a minute (the low power warning). This low power warning

should last for 30 days, but you should replace the Smoke Alarm

immediately to continue your protection.

TO PERMANENTLY DEACTIVATE THE SMOKE ALARM

Alarm is sealed. The powercell is not replaceable. Once it reaches

the end of its service life, or after 10 years—whichever comes first—

you must install a new Smoke Alarm.

After 10 years or after the “low power warning” sounds (whichever

comes first):

1. Once you deactivate this unit, it will not detect smoke or alarm.

It cannot be reactivated. You must install a new unit to continue

your protection. Alarm will resist mounting to the bracket after

deactivation.

2. Use a flathead screwdriver to score

label along dotted line.

3. Use thumb to pull deactivation tab

outward until tab snaps into place.

This will discharge the powercell

and deactivate the unit.

4. Install a new Smoke Alarm

immediately!

Specyfikacje produktu

Marka:	First Alert
Kategoria:	Detektor dymu
Model:	SA340

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z First Alert SA340, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Detektor dymu First Alert

First Alert HD6135FB Instrukcja

14 Października 2024

First Alert SA320 Instrukcja

4 Października 2024

First Alert SA410 Instrukcja

1 Października 2024

First Alert SA710LCE Instrukcja

29 Września 2024

First Alert P910 Instrukcja

27 Września 2024

First Alert 7010BSL Instrukcja

27 Września 2024

First Alert SCO5 Instrukcja

27 Września 2024

First Alert P900E Instrukcja

27 Września 2024

First Alert PC900V Instrukcja

27 Września 2024

First Alert PC910V Instrukcja

27 Września 2024

Instrukcje Detektor dymu

Najnowsze instrukcje dla Detektor dymu

Kidde 3SFWR Instrukcja

9 Października 2024

Kidde KF30R Instrukcja

9 Października 2024

Kidde P4010ACS-WCA Instrukcja

9 Października 2024

Kidde P4010DCSCO-WCA Instrukcja

9 Października 2024

Kidde i12020CA Instrukcja

9 Października 2024

Kidde i12040CA Instrukcja

9 Października 2024

Kidde KF20R Instrukcja

9 Października 2024

Kidde CP9000CA Instrukcja

9 Października 2024

Kidde Pi2010CA Instrukcja

9 Października 2024

Kidde KN-COSM-B-RF-CA Instrukcja

9 Października 2024