Instrukcja obsługi First Alert P1000

First Alert Detektor dymu P1000

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla First Alert P1000 (2 stron) w kategorii Detektor dymu. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

IMPORTANT! PLEASE READ CAREFULLY AND SAVE.

This user’s manual contains important information about your Smoke

Alarm’s operation. If you are installing this Smoke Alarm for use by

others, you must leave this manual—or a copy of it—with the end user.

Para el manual del usuario en español, por favor visite www.firstalert.com.

USER’S MANUAL

Printed in China

M08-0410-006 01/13

Distributed by BRK Brands, Inc.

3901 Liberty Street Road, Aurora, IL 60504-8122

Consumer Affairs: (800) 323-9005 • www.firstalert.com

FIRE SAFETY TIPS

Follow safety rules and prevent hazardous situations: 1) Use smoking

materials properly. Never smoke in bed. 2) Keep matches or lighters

away from children; 3) Store flammable materials in proper containers;

4) Keep electrical appliances in good condition and don’t overload elec-

trical circuits; 5) Keep stoves, barbecue grills, fireplaces and chimneys

grease- and debris-free; 6) Never leave anything cooking on the stove

unattended; 7) Keep portable heaters and open flames, like candles,

away from flammable materials; 8) Don’t let rubbish accumulate.

Keep alarms clean, and test them weekly. Replace alarms immediately

if they are not working properly. Smoke Alarms that do not work cannot

alert you to a fire. Keep at least one working fire extinguisher on every

floor, and an additional one in the kitchen. Have fire escape ladders or

other reliable means of escape from an upper floor in case stairs are

blocked.

BEFORE YOU INSTALL THIS SMOKE ALARM

Important! Read “Recommended Locations for Smoke Alarms”

and “Locations to Avoid for Smoke Alarms” before beginning. This

unit monitors the air, and when smoke reaches its sensing chamber,

it alarms. It can give you more time to escape before fire spreads.

This unit can ONLY give an early warning of developing fires if it is

installed, maintained and located where smoke can reach it, and where

all residents can hear it, as described in this manual. This unit will not

sense gas, heat, or flame. It cannot prevent or extinguish fires.

Understand The Different Type of Smoke Alarms

Battery powered or electrical? Different Smoke Alarms provide

different types of protection. See “About Smoke Alarms” for details.

Know Where To Install Your Smoke Alarms

Fire Safety Professionals recommend at least one Smoke Alarm on

every level of your home, in every bedroom, and in every bedroom

hallway or separate sleeping area. See “Recommended Locations

For Smoke Alarms” and “Locations To Avoid For Smoke Alarms” for

details.

Know What Smoke Alarms Can and Can’t Do

A Smoke Alarm can help alert you to fire, giving you precious time to

escape. It can only sound an alarm once smoke reaches the sensor.

See “Limitations of Smoke Alarms” for details.

Check Your Local Building Codes

This Smoke Alarm is designed to be used in a typical single-family

home. It alone will not meet requirements for boarding houses,

apartment buildings, hotels or motels. See “Special Compliance

Considerations” for details.

*All First Alert

®Smoke Alarms conform to regulatory requirements,

including UL217 and are designed to detect particles of combustion.

Smoke particles of varying number and size are produced in all fires.

Ionization technology is generally more sensitive than photoelectric

technology at detecting small particles, which tend to be produced

in greater amounts by flaming fires, which consume combustible

materials rapidly and spread quickly. Sources of these fires may include

paper burning in a wastebasket, or a grease fire in the kitchen.

Photoelectric technology is generally more sensitive than ionization

technology at detecting large particles, which tend to be produced

i n greater amounts by smoldering fires, which may smolder for

hours before bursting into flame. Sources of these fires may include

cigarettes burning in couches or bedding.

For maximum protection, use both types of Smoke Alarms on each

level and in every bedroom of your home.

• This unit will not alert hearing impaired residents.

It is recommended that you install special units which use

devices like flashing strobe lights to alert hearing impaired

residents.

• Do not connect this unit to any other alarm or auxiliary

device. It is a single-station unit that cannot be linked to

other devices. Connecting anything else to this unit may

prevent it from working properly.

• Unit will not operate without

battery power. The Smoke Alarm

cannot work until you install the

battery in the correct position

(Match “+” to “+”).

• This Smoke Alarm has a battery

area which resists closing

unless a battery is installed.

• Do not install this unit over an electrical junction box.

Air currents around junction boxes can prevent smoke from

reaching the sensing chamber and prevent the unit from

alarming. Only AC powered units are intended for installation

over junction boxes.

• Do not stand too close to the unit when the alarm is sounding.

It is loud to wake you in an emergency. Exposure to the horn

at close range may harm your hearing.

• Do not paint over the unit. Paint may clog the openings to

the sensing chamber and prevent the unit from operating

properly.

IF THIS SMOKE ALARM SOUNDS

RESPONDING TO AN ALARM

During an alarm, you will hear a loud, repeating horn pattern:

3 beeps, pause, 3 beeps, pause. The LED will flash rapidly.

• If the unit alarms and you are not testing the unit, it is warning

you of a potentially dangerous situation that requires your

immediate attention. NEVER ignore any alarm. Ignoring the

alarm may result in injury or death.

• Never remove the batteries from a battery operated Smoke

Alarm to stop an unwanted alarm (caused by cooking smoke,

etc.). Removing batteries disables the alarm so it cannot sense

smoke, and removes your protection. Instead open a window

or fan the smoke away from the unit. The alarm will reset auto-

matically.

• If the unit alarms get everyone out of the house immediately.

IF YOU SUSPECT A PROBLEM

Smoke Alarms may not operate properly because of dead, missing or

weak batteries, a build-up of dirt, dust or grease on the Smoke Alarm

cover, or installation in an improper location. Clean the Smoke Alarm as

described in “Regular Maintenance,” and install a fresh battery, then test

the Smoke Alarm again. If it fails to test properly when you use the test

button, or if the problem persists, replace the Smoke Alarm immediately.

• If you hear a “chirp” about once a minute, replace the battery.

• If you experience frequent non-emergency alarms (like those

caused by cooking smoke), try relocating the Smoke Alarm.

Continued...

SMOKE AND FIRE* ALARM

USING THE SILENCE FEATURE

The Silence Feature can temporarily quiet an unwanted alarm for up to

10 minutes. To use this feature, press the Test/Silence button. If the

unit will not silence and no heavy smoke is present, or if it stays

in silence mode continuously, it should be replaced immediately.

The LED will flash every 8 seconds while in silence.

The Silence Feature does not disable the unit—it makes it

temporarily less sensitive to smoke. For your safety, if smoke

around the unit is dense enough to suggest a potentially dangerous

situation, the unit will stay in alarm or may re-alarm quickly. If you

do not know the source of the smoke, do not assume it is an

unwanted alarm. Not responding to an alarm can result in property

loss, injury, or death.

WHAT TO DO IN CASE OF FIRE

• Don’t panic; stay calm. Follow your family escape plan.

• Get out of the house as quickly as possible. Don’t stop to get

dressed or collect anything.

• Feel doors with the back of your hand before opening them.

If a door is cool, open it slowly. Don’t open a hot door. Keep doors

and windows closed, unless you must escape through them.

• Cover your nose and mouth with a cloth (preferably damp).

Take short, shallow breaths.

• Meet at your planned meeting place outside your home,

and do a head count to make sure everybody got out safely.

• Call the Fire Department as soon as possible from outside.

Give your address, then your name.

• Never go back inside a burning building for any reason.

• Contact your Fire Department for ideas on making your home safer.

Alarms have various limitations. See "Limitations of Smoke Alarms"

for details.

• NEVER use an open flame of any kind to test this unit. You

might accidentally damage or set fire to the unit or to your

home. The built-in test switch accurately tests the unit’s

operation as required by ANSI/UL Standard 217.

• If the Alarm ever fails to test properly, replace it immediately.

Products under warranty may be returned to the manufacturer

for replacement. See “Limited Warranty” for details.

• DO NOT stand close to the alarm when the horn is sounding.

Exposure at close range may be harmful to your hearing. When

testing, step away when horn starts sounding.

It is important to test this unit every week to make sure it is

working properly. Using the test/silence button is the recommended

way to test this Smoke Alarm. Press and

hold the test/silence button on the unit until

the alarm sounds (the unit may continue to

alarm for a few seconds after you release

the button). If it does not alarm, make sure

the unit is receiving power (LED will flash

approximately once a minute indicating it

has power); and test it again. If it still does

not alarm, replace it immediately. During

testing you will hear a loud, repeating horn

pattern: 3 beeps, pause, 3 beeps, pause.

REGULAR MAINTENANCE

This unit has been designed to be as maintenance free as possible, but

there are a few simple things you must do to keep it working properly.

Use only the replacement batteries listed below. The unit may not

operate properly with other batteries. Never use rechargeable

batteries since they may not provide a constant charge.

• Test it at least once a week.

• Clean the Smoke Alarm at least once a month; gently vacuum off

any dust using your household vacuum’s soft brush attachment,

and test the Smoke Alarm after cleaning. Never use water, cleaners

or solvents since they may damage the unit.

• If the Smoke Alarm becomes contaminated by excessive dirt, dust

and/or grime, and cannot be cleaned to avoid unwanted alarms,

replace the unit immediately.

• Relocate the unit if it sounds frequent unwanted alarms. See

“Locations to Avoid For Smoke Alarms” for details.

• When the battery becomes weak, the Smoke Alarm unit will “chirp”

approximately once a minute (the low battery warning). This low

battery warning should last for up to 7 days, but you should replace

the battery immediately to continue your protection.

Choosing a replacement battery:

Your Smoke Alarm requires one 3V CR2 battery. The following battery

is acceptable as replacement: Duracell DLCR2. These batteries are

available at many local retail stores.

Actual service life depends on the Smoke Alarm and the environment

in which it is installed. All the batteries specified above are acceptable

replacement batteries for this unit. Regardless of the manufacturer’s

suggested battery life, you MUST replace the battery immediately once

the unit starts “chirping” (the “low battery warning”).

• Always select the correct size and type of battery most suitable for

the intended use. Information provided with the appliance to assist

correct battery selection should be retained for reference.

• Remove used batteries promptly and replace all batteries of a set at

the same time.

• Clean the battery and appliance contacts prior to battery installation.

• Ensure that the batteries are installed correctly with regard to polarity

(+ and -).

• Immediately seek medical attention if a cell or battery has been

swallowed. Also, contact your local poison control center.

CONFORMS TO

UL STD 217 Model P1000

BATTERY PLACEMENT

WEEKLY TESTING

HOW TO INSTALL YOUR SMOKE ALARM

Make sure you have read and understood this manual before installing

your smoke alarm.

1. Preparation

Attach the mounting ring to the wall or ceiling as follows:

Use the two fixing slots on the mounting ring as a guide when marking

the position of the drill holes. With an appropriately sized drill, drill the

holes and insert the plastic fixing anchors supplied (if needed).

See diagram.

2. Install Mounting Ring

Fit the mounting ring to the ceiling

or wall using the screws provided.

Ensuring that the screw heads are

flush.

Activate the battery before installing your smoke alarm by removing

the clear plastic battery spacer from underneath the battery, ensuring

the battery remains in place. Do not remove Note:

label from back of alarm.

3. Fit Your Smoke Alarm

Position the smoke alarm over the mounting

ring and turn clockwise. You should feel the

alarm click into place. The alarm will only

attach to the mounting ring with the battery

in place. This smoke alarm will not Note:

mount if a battery is not installed.

4. Test Your Smoke Alarm

See “Weekly Testing.”

Fixing slots

LIMITED WARRANTY

BRK Brands, Inc., ("BRK") the maker of First Alert®brand products

warrants that for a period of ten years from the date of purchase, this

product will be free from defects in material and workmanship. BRK, at

its option, will repair or replace this product or any component of the

product found to be defective during the warranty period. Replacement

will be made with a new or remanufactured product or component. If the

product is no longer available, replacement may be made with a similar

product of equal or greater value. This is your exclusive warranty.

This warranty is valid for the original retail purchaser from the date of

initial retail purchase and is not transferable. Keep the original sales

receipt. Proof of purchase is required to obtain warranty performance.

BRK dealers, service centers, or retail stores selling BRK products do

not have the right to alter, modify or any way change the terms and

conditions of this warranty.

This warranty does not cover normal wear of parts or damage resulting

from any of the following: negligent use or misuse of the product, use on

improper voltage or current, use contrary to the operating instructions,

disassembly, repair or alteration by anyone other than BRK or an

authorized service center. Further, the warranty does not cover Acts of

God, such as fire, flood, hurricanes and tornadoes or any batteries that

are included with this unit.

BRK shall not be liable for any incidental or consequential damages

caused by the breach of any express or implied warranty. Except to

the extent prohibited by applicable law, any implied warranty of

merchantability or fitness for a particular purpose is limited in duration

to the duration of the above warranty. Some states, provinces or

jurisdictions do not allow the exclusion or limitation of incidental or

consequential damages or limitations on how long an implied warranty

lasts, so the above limitations or exclusion may not apply to you. This

warranty gives you specific legal rights, and you may also have other

rights that vary from state to state or province to province.

How to Obtain Warranty Service

Service: If service is required, do not return the product to your retailer.

In order to obtain warranty service, contact the Consumer Affairs

Division at 1-800-323-9005, 7:30 AM - 5:00 PM Central Standard Time,

Monday through Friday. To assist us in serving you, please have the

model number and date of purchase available when calling.

For Warranty Service return to:

BRK Brands, Inc., 25 Spur Drive, El Paso, TX 79906

Battery: BRK Brands, Inc. make no warranty, express or implied, written

or oral, including that of merchantability or fitness for any particular

purpose with respect to battery.

LOCATIONS TO AVOID FOR SMOKE ALARMS, Continued

• In very damp, humid or steamy areas, or directly near bathrooms with

showers. Keep units at least 10 feet (3 meters) away from showers,

saunas, dishwashers, etc.

• Where the temperatures are regularly below 40˚ F (4.4˚ C) or above 100˚ F

(37.8˚ C), including unheated buildings, outdoor rooms, porches, or

unfinished attics or basements.

• In very dusty, dirty, or greasy areas. Do not install a Smoke Alarm directly

over the stove or range. Keep laundry room Smoke Alarms free of dust

or lint.

• Near fresh air vents, ceiling fans, or in very drafty areas. Drafts can

blow smoke away from the unit, preventing it from reaching the sensing

chamber.

• In insect infested areas. Insects can clog openings to the sensing

chamber and cause unwanted alarms.

• Less than 12 inches (305mm) away from fluorescent lights. Electrical

“noise” can interfere with the sensor.

• In “dead air” spaces. “Dead air” spaces may prevent smoke from

reaching the Smoke Alarm.

Avoiding Dead Air Spaces

“Dead air” spaces may prevent smoke from reaching the Smoke Alarm.

To avoid dead air spaces, follow the installation recommendations below.

On ceilings, install Smoke Alarms as close to the center of the ceiling as

possible. If this is not possible, install the Smoke Alarm at least 4 inches

(102 mm) from the wall or corner.

For wall mounting (if allowed by building codes), the top edge of Smoke

Alarms should be placed between 4 and 12 inches (102 and 305 mm) from

the wall/ceiling line, below typical “dead air” spaces.

On a peaked, gabled, or cathedral ceiling, install the first Smoke Alarm

within 3 feet (0.9 meters) of the peak of the ceiling, measured horizontally.

Additional Smoke Alarms may be required depending on the length, angle,

etc. of the ceiling's slope. Refer to NFPA 72 for details on requirements for

sloped or peaked ceilings.

ABOUT SMOKE ALARMS

Battery (DC) operated Smoke Alarms: Provide protection even when

e lectricity fails, provided the batteries are fresh and correctly installed.

Units are easy to install, and do not require professional installation.

However, they do not provide interconnected functionality.

AC powered Smoke Alarms: Can be interconnected so if one unit senses

smoke, all units alarm. They do not operate if electricity fails.

AC with battery (DC) back-up: will operate if electricity fails, provided the

batteries are fresh and correctly installed. AC and AC/DC units must be

installed by a qualified electrician.

Wireless Interconnected Alarms: Offer the same interconnected

functionality as with hardwired alarms, without wires. Units are easy to install

and do not require professional installation. They provide protection even

when electricity fails, provided the batteries are fresh and correctly installed.

Smoke Alarms for Solar or Wind Energy users and battery backup

power systems: AC powered Smoke Alarms should only be operated with

true or pure sine wave inverters. Operating this Smoke Alarm with most

battery-powered UPS (uninterruptible power supply) products or square

wave or “quasi sine wave” inverters . If you are notwill damage the Alarm

sure about your inverter or UPS type, please consult with the manufacturer

to verify.

Smoke Alarms for the hearing impaired: Special purpose Smoke Alarms

should be installed for the hearing impaired. They include a visual alarm and

an audible alarm horn, and meet the requirements of the Americans With

Disabilities Act. These units can be interconnected so if one unit senses

smoke, all units alarm.

Smoke alarms are not to be used with detector guards unless the

combination has been evaluated and found suitable for that purpose.

All these Smoke Alarms are designed to provide early warning of fires

if located, installed and cared for as described in the user’s manual, and if

smoke reaches the Alarm. If you are unsure which type of unit to install, refer

to NFPA (National Fire Protection Association) 72 (National Fire Alarm and

Signaling Code) and NFPA 101 (Life Safety Code). National Fire Protection

Association, One Batterymarch Park, Quincy, MA 02269-9101. Local building

codes may also require specific units in new construction or in different areas

of the home.

RECOMMENDED LOCATIONS FOR

SMOKE ALARMS

Installing Smoke Alarms in Single-Family Residences

The National Fire Protection Association (NFPA), recommends one

Smoke Alarm on every floor, in every sleeping area, and in every bed-

room. In new construction, the Smoke Alarms must be AC powered

and interconnected. See “Agency Placement Recommendations” for

details. For additional coverage, it is recommended that you install a

Smoke Alarm in all rooms, halls, storage areas, finished attics, and

basements, where temperatures normally remain between 40˚ F (4.4˚ C)

and 100˚ F (37.8˚ C). Make sure no door or other obstruction could

keep smoke from reaching the Smoke Alarms.

More specifically, install Smoke Alarms:

•

On every level of your home, including finished attics and basements.

• Inside every bedroom, especially if people sleep with doors closed.

• In the hall near every sleeping area. If your home has multiple sleep-

ing areas, install a unit in each. If a hall is over 40 feet (12 meters)

long, install an alarm at each end.

• At the top of the first-to-second floor stairway, and at bottom of

basement stairway.

Specific requirements for Smoke Alarm installation vary from state to

state and from region to region. Check with your local Fire Department

for current requirements in your area. It is recommended AC or AC/DC

units be interconnected for added protection.

LOCATIONS TO AVOID FOR SMOKE ALARMS

For best performance, it is recommended you AVOID installing Smoke

Alarms in these areas:

• Where combustion particles are produced. Combustion particles form

when something burns. Areas to avoid include poorly ventilated kitchens,

garages, and furnace rooms. Keep units at least 20 feet (6 meters) from

the sources of combustion particles (stove, furnace, water heater, space

heater) if possible. In areas where a 20-foot (6-meter) distance is not

possible – in modular, mobile, or smaller homes, for example – it is

recommended the Smoke Alarm be placed as far from these fuel-burning

sources as possible. The placement recommendations are intended to

keep these Alarms at a reasonable distance from a fuel-burning source,

and thus reduce “unwanted” alarms. Unwanted alarms can occur if a

Smoke Alarm is placed directly next to a fuel-burning source. Ventilate

these areas as much as possible.

• In air streams near kitchens. Air currents can draw cooking smoke into

the sensing chamber of a Smoke Alarm near the kitchen. Continued...

California State Fire Marshal (CSFM)

Early warning detection is best achieved by the installation of fire detection

equipment in all rooms and areas of the household as follows: A Smoke

Alarm installed in each separate sleeping area (in the vicinity, but outside

bedrooms), and Heat or Smoke Alarms in the living rooms, dining rooms,

bedrooms, kitchens, hallways, finished attics, furnace rooms, closets, utility

and storage rooms, basements, and attached garages.

AGENCY PLACEMENT RECOMMENDATIONS

NFPA 72 Chapter 29

“For your information, the ,National Fire Alarm and Signaling Code

NFPA 72, reads as follows:”

29.5.1* Required Detection.

29.5.1.1* Where required by other governing laws, codes, or standards

for a specific type of occupancy, approved single and multiple-station

smoke alarms shall be installed as follows:

(1)*In all sleeping rooms and guest rooms

(2)*Outside of each separate dwelling unit sleeping area, within 21 ft

(6.4 m) of any door to a sleeping room, with the distance measured

along a path of travel

(3) On every level of a dwelling unit, including basements

(4) On every level of a residential board and care occupancy (small

facility), including basements and excluding crawl spaces and

unfinished attics

(5)*In the living area(s) of a guest suite

(6) In the living area(s) of a residential board and care occupancy

(small facility)

(Reprinted with permission from NFPA 72®, National Fire Alarm and

Quincy, MA 02269. This reprinted material is not the complete and

official position of the National Fire Protection Association, on the

referenced subject which is represented only by the standard in its

entirety), (National Fire Alarm and Signaling Code

®and NFPA 72®are

registered trademarks of the National Fire Protection Association, Inc.,

Quincy, MA 02269).

SPECIAL COMPLIANCE CONSIDERATIONS

This Smoke Alarm is suitable for use in apartments, condominiums, town-

houses, hospitals, day care facilities, health care facilities, boarding houses,

group homes and dormitories provided a primary fire detection system

already exists to meet fire detection requirements in common areas like lob-

bies, hallways, or porches. Using this Smoke Alarm in common areas may

not provide sufficient warning to all residents or meet local fire protection

ordinances/regulations.

This Smoke Alarm alone is not a suitable substitute for complete fire detec-

tion systems in places housing many people—like apartment buildings,

condominiums, hotels, motels, dormitories, hospitals, health care facilities,

nursing homes, day care facilities, or group homes of any kind. It is not a

suitable substitute for complete fire detection systems in warehouses,

industrial facilities, commercial buildings, and special-purpose non-residential

buildings which require special fire detection and alarm systems. Depending

on the building codes in your area, this Smoke Alarm may be used to

provide additional protection in these facilities.

In new construction, most building codes require the use of AC or AC/DC

powered Smoke Alarms only. In existing construction, AC, AC/DC, or DC

powered Smoke Alarms can be used as specified by local building codes.

Refer to NFPA 72 (National Fire Alarm and Signaling Code) and NFPA 101

(Life Safety Code), local building codes, or consult your Fire Department for

detailed fire protection requirements in buildings not defined as “households”.

HUD MAP Program

Certain HUD battery powered Smoke Alarm applications, especially those

that fall under HUD 223(f) MAP (Multi-family Accelerated Processing), may

require a 10 Year sealed tamper resistant battery. This alarm does not meet

that requirement. Substitute First Alert SA340B.

LIMITATIONS OF SMOKE ALARMS

Smoke Alarms have played a key role in reducing deaths resulting from home

fires worldwide. However, like any warning device, Smoke Alarms can only

work if they are properly located, installed, and maintained, and if smoke

reaches them. They are not foolproof.

Smoke alarms may not waken all individuals. Practice the escape plan

at least twice a year, making sure that everyone is involved – from kids to

grandparents. Allow children to master fire escape planning and practice

before holding a fire drill at night when they are sleeping. If children or others

do not readily waken to the sound of the smoke alarm, or if there are infants

or family members with mobility limitations, make sure that someone is

assigned to assist them in fire drill and in the event of an emergency. It is

recommended that you hold a fire drill while family members are sleeping

in order to determine their response to the sound of the smoke alarm while

sleeping and to determine whether they may need assistance in the event

of an emergency.

Smoke Alarms cannot work without power. Battery operated units cannot

work if the batteries are missing, disconnected or dead, if the wrong type

of batteries are used, or if the batteries are not installed correctly. AC units

cannot work if the AC power is cut off for any reason (open fuse or circuit

breaker, failure along a power line or at a power station, electrical fire that

burns the electrical wires, etc.). If you are concerned about the limitations

of battery or AC power, install both types of units.

Smoke Alarms cannot detect fires if the smoke does not reach them.

Smoke from fires in chimneys or walls, on roofs, or on the other side of

closed doors may not reach the sensing chamber and set off the alarm. That

is why one unit should be installed inside each bedroom or sleeping area—

especially if bedroom or sleeping area doors are closed at night—and in the

hallway between them.

Smoke Alarms may not detect fire on another floor or area of the home.

For example, a stand-alone unit on the second floor may not detect smoke

from a basement fire until the fire spreads. This may not give you enough

time to escape safely. That is why recommended minimum protection is

at least one unit in every sleeping area, and every bedroom on every level

of your home. Even with a unit on every floor, stand-alone units may not

provide as much protection as interconnected units, especially if the fire

starts in a remote area. Some safety experts recommend installing intercon-

nected AC powered units with battery back-up (see “About Smoke Alarms”)

or professional fire detection systems, so if one unit senses smoke, all units

alarm. Interconnected units may provide earlier warning than stand-alone

units since all units alarm when one detects smoke.

Smoke Alarms may not be heard. Though the alarm horn in this unit meets

or exceeds current standards, it may not be heard if: 1) the unit is located

outside a closed or partially closed door, 2) residents recently consumed

alcohol or drugs, 3) the alarm is drowned out by noise from stereo, TV, traffic,

air conditioner or other appliances, 4) residents are hearing impaired or

sound sleepers. Special purpose units, like those with visual and audible

alarms, should be installed for hearing impaired residents.

Smoke Alarms may not have time to alarm before the fire itself causes

damage, injury, or death, since smoke from some fires may not reach

the unit immediately. Examples of this include persons smoking in bed,

children playing with matches, or fires caused by violent explosions

resulting from escaping gas.

Smoke Alarms are not foolproof. Like any electronic device, Smoke Alarms

are made of components that can wear out or fail at any time. You must test

the unit weekly to ensure your continued protection. Smoke Alarms cannot

prevent or extinguish fires. They are not a substitute for property or life

insurance.

Smoke Alarms have a limited life. The unit should be replaced immediately

if it is not operating properly. You should always replace a Smoke Alarm

after 10 years from date of purchase. Write the purchase date on the space

provided on back of unit.

First Alert®is a registered trademark of the First Alert Trust.

Printed in China M08-0410-006 01/13

IF YOU SUSPECT A PROBLEM, Continued

• If the alarm sounds when no smoke is visible, try cleaning or

relocating the Smoke Alarm. The cover may be dirty.

• If the alarm does not sound during testing, try installing a new

battery, and make sure it is snapped in securely.

If the Smoke Alarm is still not operating properly, and it is still under

warranty, please see “How to Obtain Warranty Service” in the Limited

Warranty.

Do not try fixing the alarm yourself – this will void your warranty!

Specyfikacje produktu

Marka:	First Alert
Kategoria:	Detektor dymu
Model:	P1000

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z First Alert P1000, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Detektor dymu First Alert

First Alert HD6135FB Instrukcja

14 Października 2024

First Alert SA320 Instrukcja

4 Października 2024

First Alert SA410 Instrukcja

1 Października 2024

First Alert SA710LCE Instrukcja

29 Września 2024

First Alert P910 Instrukcja

27 Września 2024

First Alert 7010BSL Instrukcja

27 Września 2024

First Alert SCO5 Instrukcja

27 Września 2024

First Alert P900E Instrukcja

27 Września 2024

First Alert PC900V Instrukcja

27 Września 2024

First Alert PC910V Instrukcja

27 Września 2024

Instrukcje Detektor dymu

Najnowsze instrukcje dla Detektor dymu

Kidde 3SFWR Instrukcja

9 Października 2024

Kidde KF30R Instrukcja

9 Października 2024

Kidde P4010ACS-WCA Instrukcja

9 Października 2024

Kidde P4010DCSCO-WCA Instrukcja

9 Października 2024

Kidde i12020CA Instrukcja

9 Października 2024

Kidde i12040CA Instrukcja

9 Października 2024

Kidde KF20R Instrukcja

9 Października 2024

Kidde CP9000CA Instrukcja

9 Października 2024

Kidde Pi2010CA Instrukcja

9 Października 2024

Kidde KN-COSM-B-RF-CA Instrukcja

9 Października 2024