Instrukcja obsługi First Alert 2602DF

First Alert Kamera monitorująca 2602DF

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla First Alert 2602DF (5 stron) w kategorii Kamera monitorująca. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/5
2601DF | 2602DF | 2603DF
MANUAL # M08-0505-004
MANUAL # M08-0505-004
www.FirstAlert.com
Waterproof Fire Safe
Operation & Installation Guide
21
INDEX
Proper Use of Your Safe 1 ...............................................................................................
Opening Your Safe for the First Time ................................................................3-4
Programming a Personal Passcode ........................................................................4
Safe Care & Maintenance / Consumer Affairs 5-6 .................................................
Safe Identification Record ..........................................................................................6
Ordering Replacement Entry Keys ..........................................................................7
Limited Warranty ..........................................................................................................8
Congratulations!
Your new First Alert® Waterproof Fire Safe will provide years of secure storage for
valuables and important documents. This safe has been built with the highest
manufacturing standards to ensure maximum user satisfaction. With proper care,
your First Alert® safe will provide peace of mind for many years to come.
PACKAGE CONTENTS
PROPER USE OF YOUR SAFE
First Alert® Waterproof Fire Safes protect paper records and other valuable
documents. UL testing shows that the interior temperature remains below
350°F for 30 minutes during a fire up to 1550° F. Your safe is protected by
our Lifetime After Fire Replacement Guarantee. Please see details in that
section on page 8.
Waterproof – Your new First Alert® Waterproof Fire Safe is designed
to help protect your valuables from fire and water. This product has
been validated to be waterproof when fully submerged for up to 1
hour and is not intended for long term underwater exposure.
Moisture Warning
We recommend that you place delicate items such as pictures or
intricate jewelry into an air-tight container before storing them in
your safe. Avoid placing your safe in areas of high humidity. For
optimum performance, the safe should be opened and aired out for
at least 20 minutes every two (2) weeks.
Firearms Warning
This safe is not designed to store medication, items with
combustible content, guns or other weapons.
To clean your safe, wash off with a damp cloth and dry. Never use paint thinners
or chemical solvents, as they can permanently damage the finish.
FOR YOUR PROTECTION
a Always store keys away from safe, NEVER INSIDE.
a Record all safe identification numbers on Safe Identification Record on page 6.
a Save this manual and NEVER keep it inside the safe. DO NOT DISCARD!
IMPORTANT: ALWAYS STORE SAFE FLAT
Index / Proper Use of Your Safe Proper Use of Your Safe
1
HOUR
1 First Alert® Waterproof Fire
Resistant Safe
MANUAL
1 Operation &
Installation Guide 2 Entry Keys
4 AA Batteries Always store your safe in a flat,
horizontal position so that
the contents remain protected
during a fire. Storing the unit on
the sides or ends WILL NOT
PROTECT CONTENTS during a fire.
43
Closing Your Safe
1 Close the lid, making sure that the contents do not obstruct the seal. Place the
keys in a secure place away from the safe.
2 Push the latch back and down onto the lid clasp and snap the latch into the
closed position.
3 Your safe is now locked.
PROGRAMMING A PERSONAL PASSCODE
For security reasons, it is very important that you program your own personal
passcode into the digital lock. The factory code should be changed immediately.
To program your own unique four to eight (4-8) digit passcode, follow these steps:
1 Open the safe using the key or the five (5) digit
passcode followed by the * key.
2 Lift the lid and locate the reset button cover.
3 Using a small Phillips screwdriver, remove the two
screws and cover.
4 Press the black reset button. The LED will flash
yellow.
5 Enter your new 4-8 digit passcode followed by the * key.
6 Reenter the new passcode again and press the * key.
7 If both entries match, the green LED will light up for 2 seconds indicating that
your new passcode has been successfully programmed. If both entries do not
match, the red LED will light up for 2 seconds and you will have to repeat steps
4-7.
8 Use a Phillips screwdriver to replace the two screws and cover.
Opening Your Safe for the First Time / Opening & Closing Your Safe
OPENING YOUR SAFE FOR THE FIRST TIME
Batteries and Keys
Remove four (4) batteries and two (2) Entry Keys. They are located in the packing
material. Remove them before discarding the box.
Installing Batteries
1 Locate the battery cover on the top of the lid.
2 Slide the cover off the battery compartment.
3 Properly insert batteries, noting the +/- directions. The LED on top of the lid
will blink red and green three (3) times.
4 Replace cover and close the lid.
NOTE: Clean the battery contacts in the battery compartment and on the
batteries before installing new batteries.
The pre-set factory code for your safe is:
OPENING & CLOSING YOUR SAFE
Opening Your Safe with the Keypad
1 Enter the factory pre-set code 1-2-3-4-5 followed by the * key.
2 After properly entering the entire sequence, the green light will turn on and
the locking latch will open and spring forward.
3 Lift the safe lid.
NOTE: If an incorrect code is entered in a row, the lock will automatically 3 TIMES
shut down for before it can be opened again using the correct code. 4 MINUTES
During this delay, the key can be used to open the safe. If an incorrect code is
entered, the red light will blink one time and you will hear 3 fast beeps.
Opening Your Safe with the Key
1 Insert the key into the lock and then turn counterclockwise (to the left).
2 The locking latch will open and spring forward.
3 Press and turn the key clockwise (to the right) to remove.
4 Lift the lid to open the safe.
Programming a Personal Passcode
*
21 3 4 5

Specyfikacje produktu

Marka: First Alert
Kategoria: Kamera monitorująca
Model: 2602DF

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z First Alert 2602DF, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Kamera monitorująca First Alert

First Alert

First Alert DWC-400 Instrukcja

26 Września 2024
First Alert

First Alert BNC-50 Instrukcja

26 Września 2024
First Alert

First Alert CM700 Instrukcja

5 Września 2024
First Alert

First Alert 2013F Instrukcja

4 Września 2024
First Alert

First Alert 2011F Instrukcja

1 Września 2024
First Alert

First Alert CO-9B-FA-BNL Instrukcja

30 Sierpnia 2024
First Alert

First Alert DWS-401 Instrukcja

29 Sierpnia 2024
First Alert

First Alert 2017F Instrukcja

28 Sierpnia 2024
First Alert

First Alert 2602DF Instrukcja

27 Sierpnia 2024
First Alert

First Alert CM520 Instrukcja

26 Sierpnia 2024

Instrukcje Kamera monitorująca

Najnowsze instrukcje dla Kamera monitorująca

Dahua Technology

Dahua Technology Pro IPC-HDPW5442G-Z Instrukcja

15 Stycznia 2025
Toshiba

Toshiba IKS-WR7412 Instrukcja

13 Stycznia 2025
AVerMedia

AVerMedia FC1320-P Instrukcja

13 Stycznia 2025
Digitus

Digitus OptiMax DN-16037 Instrukcja

13 Stycznia 2025
Hikvision

Hikvision DS-2CE59U1T-AVPIT3ZF Instrukcja

12 Stycznia 2025
Hikvision

Hikvision IDS-2CD7526G0-IZHSY Instrukcja

12 Stycznia 2025
Hikvision

Hikvision DS-2CD2163G0-I(S) Instrukcja

12 Stycznia 2025
Hikvision

Hikvision DS-2CD2H83G1-IZS Instrukcja

12 Stycznia 2025
Speco Technologies

Speco Technologies O5LB1 Instrukcja

12 Stycznia 2025
ZKTeco

ZKTeco AntarVis 2.0 Instrukcja

12 Stycznia 2025