Instrukcja obsługi Fibaro FGBRS-001

Fibaro Nawilżacz FGBRS-001

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Fibaro FGBRS-001 (27 stron) w kategorii Nawilżacz. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/27
CONTENTS
#1: Description and features 3
#2: Basic activation 4
#3: Adding to Z-Wave network 5
#4: Removing the device 6
#5: Controlling the temperature 7
#6: Extra temperature sensor 8
#7: Dismounting the device 9
#8: Menu 10
#9: Local protection 11
#10: Head calibration 12
#11: Standby Mode 13
#12: Factory reset 14
#13: Z-Wave range test 15
#14: Battery and charging 16
#15: Normal Schedules 17
#16: Override Schedule 18
#17: Z-Wave specication 19
#18: Advanced parameters 23
#19: Specications 24
#20: Accessory specication (FGBRS-001) 26
#21: Regulations 27
O P E R A T I N G
M A N U A L
EN
v1.0
THE HEAT CONTROLLER
RADIATOR THERMOSTAT
FGT-001
2
Important safety information
Read this manual before attempting to install the device!
Failure to observe recommendations included in this manual
may be dangerous or cause a violation of the law. The manufacturer,
Fibar Group S.A. will not be held responsible for any loss or damage
resulting from not following the instructions of operating manual.
!
This product is not a toy. Keep away from children and animals!
CR2032 coin cell battery is harmful if swallowed!
Battery pack warning!
The Heat Controller contains lithium-ion polymer battery pack, heed all
following warnings:
• If an unusual odor or malfunction is detected, avoid sources of
opename and remove the device from the radiator.
• In the event of damage from crashes, etc., carefully remove to a
safe place for at least a half hour to observe.
• Do not leave the device unattended while charging.
• Do not attempt to replace the battery!
General information about
the FIBARO System
FIBARO is a wireless smart home automation system, based on the
Z-Wave protocol. All of available devices can be controlled through
a computer (PC or Mac), smartphone or tablet. Z-Wave devices are
not only receivers, but can also repeat the signal, increasing the
Z-Wave network’s range. It gives advantage over traditional wireless
systems that require direct link between transmitter and receiver, as
a result the construction of the building could aect network’s range
negatively.
Every Z-Wave network has its unique identication number (home
ID). Multiple independent networks can exist in the building without
interfering. Transmission security of FIBARO System is comparable to
wired systems.
Z-Wave technology is the leading solution in smart home automation.
There is a wide range of Z-Wave devices that are mutually
compatible, independently of manufacturer. It gives the system the
ability to evolve and expand over time. For more information visit:
www.baro.com.
3
DESCRIPTION AND FEATURES
Main features of FIBARO Heat Controller:
• to be installed on three types of valves: M30 x 1.5, Danfoss RTD-N
and Danfoss RA-N,
• compatible with any Z-Wave or Z-Wave+ Controller,
• supports Z-Wave network Security Modes: S0 with AES-128
encryption and S2 with PRNG-based encryption,
• built-in battery recharged through standard micro-USB port,
• easy installation - no tools required,
• can use a dedicated temperature sensor - FGBRS-001,
• supports heating schedules,
• automatic calibration,
• anti-freeze function,
• decalc function,
• unconstrained rotation spherical knob to set desired temperature.
FIBARO Heat Controller is a remotely controlled thermostatic head
to control temperature in your room. It measures the temperature
and automatically adjust the heat level.
It can be mounted without tools on three types of thermostatic
radiator valves.
You can create schedules via app to easily manage temperature
throughout the week.
#1: Description and features
FIBARO Heat Controller is a fully
compatible Z-Wave PLUS device.
NOTE
This device may be
used with all devices
certied with Z-Wave
Plus certicate and
should be compatible
with such devices pro-
duced by other manu-
facturers.
i
NOTE
Z-Wave Controller
must support Z-Wave
Security Mode in or-
der to fully utilize the
product.
i

Specyfikacje produktu

Marka: Fibaro
Kategoria: Nawilżacz
Model: FGBRS-001

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Fibaro FGBRS-001, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Nawilżacz Fibaro

Fibaro

Fibaro FGBRS-001 Instrukcja

13 Września 2024
Fibaro

Fibaro FIBEFGFS-101-ZW5 Instrukcja

10 Września 2024
Fibaro

Fibaro FGFS-101 Instrukcja

7 Września 2024

Instrukcje Nawilżacz

Najnowsze instrukcje dla Nawilżacz

Scarlett

Scarlett SC-985 Instrukcja

15 Października 2024
Clean Air Optima

Clean Air Optima CA-703 Instrukcja

15 Października 2024
Master

Master DHA 250 Instrukcja

10 Października 2024
Philips

Philips HU1509 Instrukcja

9 Października 2024
Philips

Philips HU5710 Instrukcja

9 Października 2024
Panduit

Panduit ACF10 Instrukcja

9 Października 2024
Panduit

Panduit ACF11 Instrukcja

9 Października 2024
Scarlett

Scarlett SC-AH986M30 Instrukcja

9 Października 2024
Sencor

Sencor SHF 7647WH Instrukcja

8 Października 2024
Prixton

Prixton Essence Instrukcja

8 Października 2024