Instrukcja obsługi Ferm Concept 1500

Ferm Spawarka Concept 1500

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Ferm Concept 1500 (24 stron) w kategorii Spawarka. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/24
Ferm BV P.O. Box 134 8280 AC Genemuiden NL www.ferm.com 0301-09
Art.nr. 125020
CONCEPT 1500
UK
D
NL
F
S
SF
N
DK
R
USERS MANUAL 03
GEBRAUCHSANWEISUNG 07
GEBRUIKSAANWIJZING 12
MODE D’EMPLOI 16
BRUKSANVISNING 21
KÄYTTÖOHJE 25
BRUKSANVISNING 30
BRUGERVEJLEDNING 34
êìäéÇéÑëíÇé èé ùäëèãìÄíÄñàà 39
UK Subject to change
D Änderungen vorbehalten
NL Wijzigingen voorbehouden
F Sous réserve de modifications
S Ändringar rbehålles
SF Pidätämme oikeuden muutoksiin
N Rett till endringer forbeholdes
DK Ret til ændringer forbeholdes
R äÓÏ·ÌËfl Ferm ÔÓÒÚÓflÌÌÓ ÒÓ‚Â¯ÂÌÒÚ‚Û
ÂÚ ‚˚ÔÛÒ͇ÂÏÛ ˛ ² ÔÓ‰ÛÍˆË˛.
èÓÁÚÓÏÛ ÚÂıÌ˘ÂÒË ı‡‡ÍÚÂËÒÚËÍË
ÏÓ„ÛÚ ‚ÌÓÒËÚ¸Òfl ·ÂÁ Ô‰‚‡ËÚÂθÌÓ„Ó
ۂ‰ÓÏÎÂÌËfl.
Fig.A
Fig.B
Fig.C
Fig.D
2Ferm Ferm 47
EXPLODED VIEW
46 Ferm
SPARE PARTS LIST CONCEPT 1500
REF NR DESCRIPTION FERM NR
001 SWITCH (5 CONT. POINTS) 100357
002 THERMAL FUSE 100015
005 GRIP 100009
006 HANDWHEEL + ADJUSTMENT SCREW (23CM) 100010
006 HANDWHEEL + ADJUSTMENT SCREW (26CM) 100011
007 PULL RELIEF 101737
010 CURRENT INDICATOR 100003
011 SHUNT 101426
012 SPRING FOR SHUNT 102152
013 BACKPANEL 100008
- SWITCH (4 CONT.POINTS) 100004
- SCALING HAMMER/STEEL WIRE BRUSH 100005
- WELDING GLASS 140500
- WELDING MASK (EXCL. GLASS) 100007
WELDING MACHINE
THE NUMBERS IN THE FOLLOWING TEXT COR-
RESPOND WITH THE PICTURES AT PAGE 2
TECHNICAL SPECIFICATIONS
DESCRIPTION
EN 50060 Standard relative to welders for limited
use.
Onephase transformer.
P (W) Power in Watts.
Uo (V) No-load voltage in Volt.
f (Hz) Mains frequency in Herz.
I2 (A) Conventional welding current in ampère.
d (mm) Diameter of electrodes in mm.
nc Number of electrodes starting at room
temperature until thermostat intervenes.
nh Number of weldable electrodes after.
thermostat intervenes in first hour.
U1 (V) Mains voltage in Volt.
I1Max (A) Maximum absorbed current. Value in
ampère of use or automatic switch.
Fuse.
IP21 Protection grade covering.
HClass of isolation of transform.
Thermostat.
Collet.
Work collet.
Standardized plug.
ACCESSORIES AND SPARE PARTS
The following is supplied with your welding machine:
• Manual
• Cables
Work clamp
Collet clamp
Protective mask
Scaling hammer
• Steelbrush.
Spare parts are available through your local Ferm dealer.
When ordering parts, use the numbers listed in the Parts
List. Parts without an number are not available.
SAFETY INSTRUCTIONS
The following symbols are used in these instructions for
use:
Denotes risk of personal injury, loss of life or
damage to the tool in case of non-observance of the
instructions in this manual.
Denotes risk of electric shock.
Carefully read this manual before using the machine.
Make sure that you know how the machine functions and
how to operate it. Maintain the machine in accordance
with the instructions to make sure it functions properly.
Keep this manual and the enclosed documentation with
the machine.
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions.
SPECIAL SAFETY RULES
Arc welding produces sparks and fused metal projec-
tiles and fumes: remove all flammable substances and
materials from work area.
Provide adequate ventilation of facilities where wel-
ding takes place. Arc welding emits fumes which can
be dangerous.
Do not weld on containers or pipes which hold or
have held flammable liquid or gaseous combustibles
(danger of explosions and/or fires) or on materials
cleaned with chlorinated solvents or on varnished
surface (danger of toxic fumes).
Make sure connection is correct from welder to sup-
ply (mains connection). Any electric shock received
is potentially lethal.
Avoid stretching the supply cable; unplug before
moving machine.
Keep welding cables, elektrode holder and work
clamp in good condition; wearing out of isolation and
structural parts carrying current is DANGEROUS
and results in poor welding quality.
Avoid direct contact with welding circuit. The no-
load voltage between collet and work clamp can be
dangerous.
Do not use the machine in damp or wet places and do
not weld in the rain.
Always protect your eyes with the fitting glasses
(grade DIN 9 - 10) equipped with this machine.
Use gloves and proper protective clothing which are
dry and not soiled by oil or grease.
Avoid exposing skin to the ultraviolet rays produced
by the arc. The light radiation produced by the arc can
damage eyesight and cause burns on the skin.
This welder is automatically protected from thermic
overheating (thermostat automatic re-start). When
the windings reach performance temperature, the
protection cuts off the supply circuit. After a few
minutes cooling the protection will reopen the sup-
ply line. The welder is ready for further use.
Mains voltage | 230 V~
Frequency | 50 Hz
Absorbed power max. | 2.5 kVA
Welding current | 40 - 140 A
No load voltage | 45 - 48 V
Usable electrodes | 1.5 - 3.15 mm
Weight | 14.0 kg
UK English
Ferm 3


Specyfikacje produktu

Marka: Ferm
Kategoria: Spawarka
Model: Concept 1500

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Ferm Concept 1500, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą