Instrukcja obsługi Ferm BLM1003

Ferm Niesklasyfikowane BLM1003

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Ferm BLM1003 (18 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/18

Ferm B.V. • P.O. Box 134 • 8280 AC Genemuiden • NL • www.ferm.com 0208/28

Ferm FM-760/300T

FM-1000/350T

Metal turning lathe (2)

Metalldrehbank (5)

Metaaldraaibank (8)

Tour à métaux (11)

Metallsvarv (15)

Metallisorvi (18)

Metaldrejebænk (20)

Dreiebenk for metall (23)

íÓÍ‡Ì˚È ÒÚ‡ÌÓÍ ÔÓ

ÏÂÚ‡ÎÎÛ (26)

USERS MANUAL

GEBRAUCHSANWEISUNG

GEBRUIKSAANWIJZING

MODE D’EMPLOI

BRUKSANVISNING

KÄYTTÖOHJE

BRUKSANVISNING

BRUGER VEJLEDNING

êìäéÇéÑëíÇé èé ùäëèãìÄíÄñàà

Art. nr: 331710

Art. nr: 331730

2Ferm

Product: Ferm Metal turning lathe.

Type FM-760/300T; art. nr. 331710

Type FM-1000/350T; art.nr. 331730

Ferm, Genemuiden, The Netherlands.

Sound pressure level (Lpa): < 82 dB(A)

The sound-pressure level in the workplace

may exceed 85 dB(A). In this case, measures

for noise protection and ear protection for

the user are necessary.

READ THE INSTRUCTIONS FOR USE

BEFORE YOU USE THE METAL TURNING

LATHE !

1. USE

This universal turning lathe is suitable for different types

of turning activities and also for drilling out, drilling,

grooving etc. In addition, the machine can also be used for

cutting screw thread (both metric and inches). The ma-

chine takes up little space and also distinguishes itself by

its simple construction, ease of operation and its large

spindle bore.

2. SPECIAL SAFETY REGULATIONS

The turning lathe has been designed to machine hard

material and it must therefore be capable of genera-

ting much power.

It is therefore fatally dangerous to touch moving

parts. For this reason, improper, undesired or unin-

tentional engaging of the machine must therefore be

avoided.

Due to the spring-mounted working of the cutter,

metal particles can be shot off, so to speak, with gre-

at force and at the most unexpected moments.

- Protection of the eyes is therefore extremely impor-

tant. Make it a habit to wear specially available safety

glasses when in the area where the turning lathe is po-

sitioned. Buy yourself a pair of professional and ap-

proved safety glasses which you can wear for longer

periods after each other and for visitors, if necessary,

a slightly cheaper but nevertheless good pair.

- By making sure that the workplace is tidied up, you

can prevent, for example, people grabbing the machi-

ne or falling into it after tripping over material lying

about.

Be extremely careful when working turning work-

pieces by hand.

- If you wish to polish a surface while it is turning, use a

sufficiently long piece of sandpaper which you place

halfway around the workpiece with the ends towards

you.

- Never wrap the ends around your fingers and never

press the sandpaper onto the workpiece using your

hands.

- Due to turning, the edges of the workpiece become

razor-sharp. First smooth off these edges with a file

or a trimming hook.

During turning, never remove chips with your fingers.

Do this by using a self-made hook from wire or buy a

professional chip hook.

During turning, when something falls into or behind

the bed, never reach across the turning machine or

lathe chuck.

Always stop the machine first.

Good lighting prevents you operating the machine

from too close by.

- When using strip lighting, the so-called stroboscopic

effect must be taken into consideration. As a result, a

turning object can appear to be standing still. A solu-

tion is the use of double fittings whereby a phase shift

of both strip lights has been realized.

3. INSTALLATION

1. Remove the paper which covers the unpainted parts

and remove all the grease from these parts using a

non-volatile solvent and a brush.

2. Fit the straps as shown in Illustration 1 and position

the machine in its place.

3. The machine must be firmly fastened to the floor by

means of the supports. If you have a bench centre lat-

he, place the chip collecting vessel on the workbench

and, using a pencil, indicate the spot where the six bolt

holes will be placed for fastening the bed. Then drill

the six holes.

4. In order to be able to work accurately, the bed must

always be level. Follow the method of work described

below:

- Slide the carriage in the direction of the fixed head.

- Place the spirit level at an angle of 90° on top of the

cross slide.

- Loosen the fastening bolts and raise the support (or

the bed) until the air bubble in the spirit level is exactly

UK English

Ferm 35

Art.

nr. Type

V~/Hz W RPM mm. mm

331710 FM-760/300T 400 1.125 50-1.500 150 760

331730 FM-1000/350T 400 1.125 50-1.500 175 1000

2 1

3 5 4 7 6 8

Fig. 8

Ferm 3

in the centre.

- Tighten down the bolts again.

- Slide the carriage in the direction of the loose head

and repeat the procedure. Then check again whether

the machine is level on the side of the fixed head and

continue until both sides of the machine are level.

5. During transport and unpacking, some litter will pro-

bably have landed on the turning lathe. Do not move

the carriage or the loose head before the bed has

been cleaned thoroughly.

4. ELECTRICAL CONNECTIONS

- Check whether the connecting voltage stated on the

type plate corresponds to the mains voltage. Machi-

nes with the indication of 400 Volts can simply be con-

nected to a voltage of 380 Volts.

- For connecting to another mains voltage, consult the

wiring diagram in the lid of the engine housing.

- Connect the machine to an earthed power source.

- The electric control box is situated behind the fixed

head.

- Put the control switch handle in the central position

and press the "power start" knob to engage the po-

wer. When the cs handle is in the foremost position,

the shaft turns to the left; when the handle is in the re-

ar position, the shaft turns to the right. If this is not the

case, switch off the power and change the wiring as in-

dicated in the wiring diagram.

- Stop the machine by placing the control switch in the

central position. When the reset knob is pressed the

machine will start again.

5. PUTTING INTO OPERATION

1. Before use, read the instructions for use carefully so

that you know how to adjust, operate, grease and

maintain the machine etc.

2. The machine is equipped with 2 V-belts which run fr-

om the engine to the bottom most, back pulley.

Check the tension of the V-belt before starting the

machine. If you press carefully on the V belt, you

should be able to press it in by approximately 1.5 cm. If

the V belt is too tight it can damage the bearing. Chan-

ge the tension, if necessary.

3. Before doing a test run, place the speed adjuster in the

lowest position and allow the machine to run for ap-

proximately 20 minutes. If the machine is working

normally, increase the speed step by step until the hig-

hest speed has been reached (feed lever in central po-

sition). Continually allow the machine to run for ap-

proximately 5 minutes by every speed.

The speed can only be changed if the engine is at

a complete standstill.

6. OPERATING HANDLES

(See Illustration 2)

FIXED HEAD

- By means of the handles 1 and 2 and the V-belts, the

speed of the fixed head can be adjusted in 2 steps, in-

creasing from 60 to 1,500 revolutions per minute, as

is shown in the "Spindle speed" table which is situated

on the front of the fixed head.

- The spindle can only be started and stopped using the

starting handle (11). When the handle is raised, the

spindle turns to the left; when the handle is lowered, it

turns to the right.

GEARBOX

- By means of handle (4) a choice can be made between

threading or turning. The left position is for the feed

shaft, the central position is neutral and the right posi-

tion is for the lead screw.

- By means of handles (5) and (6) the gearbox can be

operated. Handle (5) has five positions, handle (6) has

eight positions. Using these two handles, all kinds of

feeding speeds to the left of the fixed head can be ad-

justed (Illustration 3), and screw thread pitches (in-

ches) on the front of the fixed head (Illustration 4). By

means of the metric change wheels, metric screw th-

reads can also be adjusted with the two handles, using

the "conversion table" on the front of the fixed head

(Illustration 5).

Make sure that the spindle is at a complete

standstill before using one of the three handles

referred to above.

CARRIAGE

- Handwheel (7) is used to move the carriage by hand

over the bed.

- By means of the arm for the cross feed (19) the tool

holder can be turned in or out. It can be placed in its

entirety at any angle desired and can also be used for

cutting screw thread or applying a corner to a work-

piece.

- By means of the start/stop handle (11) the direction of

running of the spindle can be changed.

- The thread screw handle (9) is used for the lead screw

nuts during cutting of the screw thread.

- By means of the handle for the feed movement (8) a

choice can be made between feeding lengthwise or

crosswise. This handle has a protection device which

makes sure that the lead screw nuts cannot be put in

operation by accident if the turning lathe is in the feed

position. There are three positions: the central posi-

tion is neutral, the uppermost position is for feeding

in a lengthwise direction and the bottommost posi-

tion is for feeding in a crosswise direction.

- The handle for the feed movement (3) is used to chan-

ge the direction of the feed movement, while the

spindle continues to turn in the same direction.

34 Ferm

POSITION

CHANGE GEAR CHART FOR MM SIZE

F G 1 2 3 4 5 6

B1.2

25 60 C 0.6

D0.3

A2.0

B1.0 0.9

26 60 C 0.7 0.5 0.45

D0.35 0.5

A4.5 4 3.0

B2.25 1.5

43 60 C 1.125 0.75

A3.5

B1.75

46 60 C 0.875 0.8

D0.4

E0.2

B2.5 2.2

47 60 C 1.25 1.1

D0.55

COMBINATION

PITCH MM

OF GEARS

Fig. 5

1 2

Fig. 6 Fig. 7

Specyfikacje produktu

Marka:	Ferm
Kategoria:	Niesklasyfikowane
Model:	BLM1003

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Ferm BLM1003, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Niesklasyfikowane Ferm

Ferm FBS-700 Instrukcja

15 Września 2024

Ferm HDM1040P Instrukcja

11 Września 2024

Ferm BLM1003 Instrukcja

11 Września 2024

Ferm FCT-360L Instrukcja

10 Września 2024

Ferm GGM1003 Instrukcja

5 Września 2024

Ferm LBM1010 Instrukcja

5 Września 2024

Ferm BCM1008 Instrukcja

2 Września 2024

Ferm FPFL-1800 Instrukcja

30 Sierpnia 2024

Ferm ETM1005 Instrukcja

26 Sierpnia 2024

Ferm PDM1050P Instrukcja

23 Sierpnia 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024

Stihl HT 70 Instrukcja

15 Października 2024

Ernesto H14270 Instrukcja

15 Października 2024

Uniden BT MIC KIT Instrukcja

15 Października 2024

Vaude Omnis Bike 26 Instrukcja

15 Października 2024

ART ProChannel II Instrukcja

15 Października 2024

Aukey DR02J Instrukcja

15 Października 2024

Master Lock 653EURD Instrukcja

15 Października 2024

Roland FR-18 Diatonic Instrukcja

15 Października 2024