Instrukcja obsługi Fender KXR 100

Fender klawiatura KXR 100

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Fender KXR 100 (6 stron) w kategorii klawiatura. Ta instrukcja była pomocna dla 17 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/6
T H E S O U N T H A T C R E A T E S L E G E N D SD
P/N 047761
Owner,s Manual
KXR
KEYBOARD
EXTENDED
RANGE
One hundred
TYPE: PR 262
KXR 100 Owner’s Manual
Congratulations on your purchase of the Fender KXR 100
keyboard amplifier. The is the most recentFender KXR 100
effort in state of the art keyboard amplifier technology, and is
a member of the series. The design execution ofFENDER KXR
the KXR 100 was carried out with the aid of some of today’s
best musicians, and represents years of thought and
consideration in determining features and specifications.
The KXR 100 is actually much more than a keyboard amp.
With its heavy-duty
Fender Special Design
speaker and dual
piezo-electric horn, it could actually be classified as a
self-contained portable PA. system, suitable for almost any
musical instrument requiring full-range reinforcement, for
example electronic keyboards, acoustic/electric guitar,
electric violin, and voice. Compact packaging and
medium-level output power make the the perfectKXR 100
full-range instrument amplifier for rehearsal, studio, or small
club performances.
The preamp section of the features threeKXR 100
independent channels, a 4 band master EQ, and master
reverb and volume controls. Each channel features a single
1/4 inch input jack and volume control. In addition to the
1/4 inch input jack, channel #1 features an XLR input jack for
the connection of a low impedance microphone. The
EFFECTS SEND and EFFECTS RETURN jacks can be used with
a wide variety of effects devices, or as patch points for
slaving multiple amps together. The EFFECTS SEND can also
be used to connect your directly to a recordingKXR 100
console or sound reinforcement mixer.
The HEADPHONE jack automatically mutes the speaker while
driving stereo or mono headphones for private practice
sessions. The HEADPHONE jack can also be used as another
line level output. RECORD OUT RCA jacks are provided to
deliver a line level preamp signal for tape recording
convenience.
The rugged 80 watt power amplifier was designed to give
years of reliable service under all conditions and is equipped
with a unique implementation of our exclusive
DELTACOMP™ adaptive compression system. When
DELTACOMP™ engages, it is practically impossible to cause
the power amplifier to clip (distort). With DELTACOMP™,
apparent compressor release time is kept short, yet waveform
distortion is kept to a minimum at low frequencies.
The selection of a Fender amplifier will reward you with years
of quality music in a wide range of sonic possibilities. This
manual is designed to familiarize you with the features and
functions of your amplifier. Read this manualKXR 100
carefully so you will benefit from these features as soon as
you start using your new Fender amplifier.
The built-in quality of a Fender amplifier is the result of over
four decades of dedication in the combined skills of the
Fender design team. That’s why we proudly say,
FENDER..
The
Sound
That Creates
Legends.
recording or sound reinforcement mixer. In addition, this
output can be used to drive another KXR 100 as a slave amp.
This is done by connecting a standard guitar cord from the
Effects Send jack of the master amp to the Effects Return jack
of the slave amp.
H. Effects Return jack- This balanced jack inputs signal to the
Master Volume control, which drives the power amp section.
It automatically disconnects the preamp when used. This jack
is useful with the effects loop feature, or when using the KXR
100 as a slave amp.
1. Master Volume control- This control adjusts the level of the
signal coming out of the preamplifier section. This control is
used in conjunction with the Channel Volume controls to set
the overall sound level of the amplifier. In order to maximize
headroom and minimize noise, instruments with low-level
output will require a high Channel Volume setting and a low
Master Volume setting, while other instruments may require a
lower Channel Volume and higher Master Volume setting. It
is recommended that the Master Volume control be set as
high as possible for maximum DELTACOMP’ compressor
range.
J. Record Out jack- Two RCA style jacks provide an
unbalanced, mono signal for recording. This signal is derived
from the preamp and is at line level, similar to that of the
Effects Send jack. The level is not affected by the Master
Volume Control.
K. Headphone jack- This jack allows the use of stereo
headphones for private listening. When this jack is used, the
internal speaker is disconnected. WARNING: BE CAREFUL
WHEN USING HEADPHONES, AS EXCESSIVE VOLUME
WILL DAMAGE YOUR HEARING.
L. Power Indicator- When this LED is illuminated, the KXR
100 is receiving power.
M. Power Switch- This switch turns the KXR 100 or Off.
When the switch is off, the amplifier is completely shut down.
A. Channel 1 Input (XLR)- A high sensitivity, XLR style
connector designed for use with microphones. This balanced
input can handle as much as 1V R.M.S.
B. Channel 1 Input (Phone)- Plug-in connection for
instruments. This balanced input can handle as much as 8V
R.M.S.
C. Channel 1 Volume- This control adjusts the preamplifier
gain of channel 1. It works in conjunction with the Master
Volume control (item 1) to set the overall loudness of the
amplifier for channel 1 only. Being a true “gain” control, it
allows for the use of a variety of microphones, keyboards or
other instruments with differing output signal levels. Low-
level instruments generally require a higher Channel Volume
setting while “hotter” keyboards will require a lower setting.
D. Channels 2 and 3 - These channels are provided for two
additional instruments. The inputs and volume controls
operate in the same manner as items B and C in Channel 1.
These channels are muted when nothing is plugged into their
inputs, and thus will contribute no additional residual noise
to the amplifier output when left unused. All three channels
may be used simultaneously, however Channel 1 should be
used first if only one input is needed.
E. Equalizer- The equalizer allows precise adjustments of the
tonal characteristics of the amplifier. Each control provides a
12 dB boost or cut to bands of frequencies centered about
100, 338,1588, and 4000 Hz.
F. Reverb control- This control adjusts the amount of reverb to
be mixed with the dry signal. The input to the reverb circuitry
is the sum of channels 1, 2 and 3.
G. Effects Send jack- This jack provides an unbalanced
output signal from the preamp. This output can be used with
the Effects Return jack (item H) as a patch point for mono
effects devices. The Effects Send is connected to the input of
the effect (digital delay or other effects device) and the output
of the effect is connected to the Effects Return jack (item H).
The Effects Send can also be used to provide a signal to a
KXR 100 Front Panel Functions

Specyfikacje produktu

Marka: Fender
Kategoria: klawiatura
Model: KXR 100

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Fender KXR 100, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje klawiatura Fender

Fender

Fender KXR 100 Instrukcja

14 Września 2024
Fender

Fender KXR 60 Instrukcja

12 Września 2024
Fender

Fender KXR 200 Instrukcja

5 Września 2024

Instrukcje klawiatura

Najnowsze instrukcje dla klawiatura

Trust

Trust 14960 Instrukcja

15 Stycznia 2025
Yamaha

Yamaha Electone B-4C Instrukcja

14 Stycznia 2025
Samson

Samson Graphite M32 Instrukcja

14 Stycznia 2025
Samson

Samson Graphite 25 Instrukcja

14 Stycznia 2025
Logitech

Logitech K120 Toetsenbord QWERTY Instrukcja

14 Stycznia 2025
Kawai

Kawai ESX Instrukcja

11 Stycznia 2025
Apple

Apple wireless keyboard Instrukcja

11 Stycznia 2025
ModeCom

ModeCom MC-TPK2 VOYAGER Instrukcja

11 Stycznia 2025
Evolveo

Evolveo K1050 Instrukcja

9 Stycznia 2025
Perixx

Perixx PERIBOARD-716 III Instrukcja

8 Stycznia 2025