Instrukcja obsługi Fellowes Powershred DS-1200C

Fellowes Niszczarka do papieru Powershred DS-1200C

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Fellowes Powershred DS-1200C (4 stron) w kategorii Niszczarka do papieru. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

Quality Office Products Since 1917

Please read these instructions before use.

Do not discard: keep for future reference.

POWERSHRED®

DS-1200Cs

CAPABILITIES

ENGLISH

Model DS-1200Cs

Will shred: Paper, credit cards, staples, small paper clips and junk mail

Will not shred: Continuous forms, adhesive labels, transparencies, newspaper,

CD/DVDs, cardboard, large paper clips, laminates, file folders, X-rays or plastic other than

noted above

Paper shred size:

Cross-Cut ......................................................................................................4mm x 50mm

Maximum:

Sheets per pass ........................................................................................................... 12*

Cards per pass ............................................................................................................... 1*

Paper entry width .................................................................................................. 225mm

* A4 (70g), paper at 220-240V, 50/60 Hz, 2.45Amps; heavier paper, humidity or other than

rated voltage may reduce capacity. Maximum recommended daily usage rates: 120 sheets;

10 credit cards. 12 sheets per pass to avoid jams.

Fellowes SafeSense® shredders are designed to be operated in home and office environments ranging

between 50 – 80 degrees Fahrenheit (10 – 26 degrees Celsius) and 40 – 80% relative humidity.

KEY

H. Control Switch and Indicator lights

R 1. Reverse

O 2. OFF

I 3. Auto-On (green)

4. Overheat (red)

5. SafeSense

indicator (yellow)

A. SafeSense

Technology

B. Paper/Card entry

C. Handle

D. Window

E. Pull-out Bin

F. Disconnect power switch

1. OFF

2. ON

G. See safety instructions

B. G.

IMPORTANT SAFETY INSTRUCTIONS — Read Before Using!

• Operation,maintenance,andservicerequirementsarecoveredin

the instruction manual. Read the entire instruction manual before

operating shredders.

• Keepawayfromchildrenandpets.Keephandsawayfrompaper

entry. Always set to off or unplug when not in use.

• Keepforeignobjects–gloves,jewelry,clothing,hair,etc.–away

from shredder openings. If object enters top opening, switch to

Reverse (R) to back out object.

• Never use aerosol products, petroleum based lubricants or other flammable

products on or near shredder. Do not use canned air on shredder.

• Donotuseifdamagedordefective.Donotdisassembleshredder.

Do not place near or over heat source or water.

• This shredder has a Disconnect Power Switch (F) that must be in the ON (I)

position to operate shredder. In case of an emergency move switch to OFF (O)

position. This action will stop shredder immediately.

• Avoidtouchingexposedcuttingbladesundershredderhead.

• Shreddermustbepluggedintoawalloutletorsocketofthevoltageandamperage

designatedonthelabel.Theoutletorsocketmustbeinstalledneartheequipment

and easily accessible. Energy converters, transformers, or extension cords should

not be used with this product.

• FIREHAZARD–DoNOTshredgreetingcardswithsoundchipsorbatteries.

• Forindooruseonly.

• Unplugshredderbeforecleaningorservicing.

BASIC SHREDDING OPERATION

Continuous operation:

Upto5minutemaximum

NOTE: Shredder runs briefly after

each pass to clear entry. Continuous

operation beyond 5 minutes will

trigger a 30-minute cool down period.

PAPER/CARD

DS-1

Set to Auto On

(I)

Feed paper/card

straight into paper

entry and release

When finished

shredding set to

OFF (O)

Plug in and put

disconnect power

switch in ON (I) position

21 3 4

LIMITED PRODUCT WARRANTY

TROUBLESHOOTING

Alternate slowly back and forthSet to Reverse (R)

for 2-3 seconds

Set to Off (O)

and unplug

Gently pull uncut paper

from paper entry. Plug in.

Set to Auto-On (I) and

resume shredding

1 2 3 4 5 6

PAPER JAM

ADvANCED PRODUCT FEATURES

SafeSense®

Technology

Stops shredding immediately when

hands touch the paper opening.

Overheat Indicator: When the Overheat Indicator is illuminated, the shredder has exceeded its maximum operating temperature and needs to cool down. This indicator

will remain illuminated and the shredder will not operate for the duration of the recovery time. See Basic Shredding Operation for more information about the

continuous operation and recovery time for this shredder.

SafeSense

Indicator: If hands are too close to the paper entry, the SafeSense

indicator will illuminate and the shredder will stop shredding.

PRODUCT MAINTENANCE

TO CLEAN THE SENSORS

CLEANING AUTO-START INFRARED SENSORS

Paper detection sensors are designed for maintenance free operation. However, on rare occasions, the

sensors may become blocked by paper dust causing the motor to run even if there is no paper present.

(Note: two paper detection sensors are located in the center of the paper entry).

Allcross-cutshreddersrequireoilforpeakperformance.Ifnotoiled,a

machine may experience diminished sheet capacity, intrusive noise when

shredding, and could ultimately stop running. To avoid these problems, we

recommend you oil your shredder each time you empty your waste bin.

OILING SHREDDER

* Only use a non-aerosol vegetable oil in long

nozzle container such as Fellowes 35250

Turn off and unplug

shredder

Locate Auto-start

infrared sensor

Usingcottonswab,wipe

away any contamination

from the paper sensors.

Dip cotton swab in

rubbing alcohol

FOLLOW OILING PROCEDURE BELOW AND REPEAT TWICE

* Apply oil

across entry

Set to Off (O) Set to Reverse (R)

2-3 seconds

DS- 1200C

1 3 1

DS-1200C

Limited Warranty: Fellowes, Inc. (“Fellowes”) warrants the parts of the machine to be free of

defects in material and workmanship and provides service and support for 2 years from the date

of purchase by the original consumer. Fellowes warrants the cutting blades of the machine to

be free from defects in material and workmanship for 5 years from the date of purchase by the

original consumer. If any part is found to be defective during the warranty period, your sole and

exclusive remedy will be repair or replacement, at Fellowes’ option and expense, of the defective

part. This warranty does not apply in cases of abuse, mishandling, failure to comply with product

usage standards, shredder operation using an improper power supply (other than listed on

label), or unauthorized repair. Fellowes reserves the right to charge the consumers for any

additional costs incurred by Fellowes to provide parts or services outside of the country where the

shredderisinitiallysoldbyanauthorizedreseller.ANYIMPLIEDWARRANTY,INCLUDINGTHATOF

MERCHANTABILITYORFITNESSFORAPARTICULARPURPOSE,ISHEREBYLIMITEDINDURATION

TO THE APPROPRIATE WARRANTY PERIOD SET FORTH ABOVE. In no event shall Fellowes be liable

foranyconsequentialorincidentaldamagesattributabletothisproduct.Thiswarrantygivesyou

specific legal rights. The duration, terms, and conditions of this warranty are valid worldwide,

exceptwheredifferentlimitations,restrictions,orconditionsmayberequiredbylocallaw.For

more details or to obtain service under this warranty, please contact us or your dealer.

Australia Residents Only:

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other

reasonablyforeseeablelossordamage.Youarealsoentitledtohavethegoodsrepairedorreplacedifthegoodsfailtobeofacceptablequalityandthefailuredoesnotamounttoamajorfailure.