Instrukcja obsługi Felisatti DMF32

Felisatti Wiertarka DMF32

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Felisatti DMF32 (36 stron) w kategorii Wiertarka. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/36
TECHNICAL DATA
Drill DMF23/1150VSE DMF32/1600VSE
Rated power W 1150 1600
No load speed r.p.m 120-480/255-970 130-280/240-510
Bit adaptation cone Morse 2 3
Maximum capacity in steel mm 23/13 32/16
Maximum capacity in aluminium mm 32/16 50/25
Maximum capacity in wood mm 60/32 80/40
∅ head setting neck mm 43 63
A
pprox. weight Kg. 4.4 5.8
The instructions contained in this manual must be strictly
followed, it should be carefully read and kept close at
hand to use when carrying out maintenance on the
indicated parts.
If the machine is used carefully and normal maintenance
is carried out, it will work well for a long time.
The functions and use of the tool you have bought shall
be only those described in this manual. Any other use
of the tool is strictly forbidden.
ILLUSTRATIONS
DESCRIPTION (See figures)
B On-/off switch (Fig.1 and 3)
C Retainer button (Fig.1 and 3)
D Mechanical speed shift lever (Fig.1 and 2)
E Auxiliary grip (Fig.1)
SAFETY INSTRUCTIONS
• See “Safety Instructions” manual, supplied with this
instruction manual.
• Warning! When drilling in amianthus/asbestos
and/or silica stone, the dust produced is extremely
harmful to your health. Wear protection against
inhalation of this dust, in compliance with current
regulations on accident prevention. Follow the in-
surance company’s safety instructions regarding
the responsibility of employees.
• For your personal safety, always connect the machine
to a mains supply protected by a differential and ther-
mal cut-out switch, in accordance with regulations on
low-voltage wiring sitemaps.
• Do not perforate the machine casing, as this would
destroy the protective insulation (use adhesive labels).
• Always unplug the machine before doing any work
on it.
• Warning! Before each use, inspect the plug and lead.
Should they need replacing, have this done by an offi-
cial service centre. Only plug the machine in when it is
switched off.
• Always keep the lead out of the machine’s working
area.
• Only plug the machine in when it is switched off.
• Do not allow the machine to get wet, nor should it be
used in wet environments.
• When using the machine, always wear safety goggles,
gloves and non-slip footwear, and it is advisable to
wear ear protection.
• Do not touch the bit during or immediately after
working, as it becomes very hot and can cause
serious burns.
• Hold the machine firmly by the handle and the auxiliary
handle, otherwise the recoil produced could cause the
machine to work imprecisely or even dangerously.
• Always use the auxiliary handle.
• Never attempt to clean off dust or shavings resulting
from drilling when the machine is operating.
• Do not use diamond core bits.
• When drilling walls, ceilings or floors, take care to
avoid electric wires and gas or water pipes.
BRIEF DESCRIPTION (Mod. DMF32/1600VSE)
The machine is equipped with a safety clutch or mecha-
nism which operates when a bit seizes up, protecting the
user and the machine’s electro-mechanical parts. The
clutch is released automatically.
Warning! This machine must not be used with hole
saws, core bits, etc, as they tend to jam in the hole
easily. This would cause the safety clutch to trip out
too often.
BEFORE USING THIS TOOL
WARNING! Before carrying out any work, check, for
instance, using a metal detector, that there are no elec-
tric wires or gas or water pipes under the surfaces you
wish to work on.
Make sure the mains voltage is correct: it must be
the same as that on the specification label. Ma-
chines with 230V can also be connected to a 220-V
mains supply.
To turn the machine on, press the ON/OFF switch B and
keep it pressed down.
When the ON/OFF switch is released, the machine
stops.
For permanent operation, press the switch and lock it
(Fig.3) by pushing the retainer button C on the actual
trigger. For accurate drilling it is advisable no to lock
the switch.
WARNING! Always disconnect the plug from the socket
before doing any work on the machine.
Mains connection
Warning! Connect only to a single-phase AC current
supply and only to the mains voltage specified on the
rating plate. Connection to sockets without earth protec-
tion is possible as the appliance features protective
class II insulation according to European Standard EN
60745. Radio interference suppression complies with the
European Standard EN 55014.

Specyfikacje produktu

Marka: Felisatti
Kategoria: Wiertarka
Model: DMF32

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Felisatti DMF32, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Wiertarka Felisatti

Felisatti

Felisatti DMF32 Instrukcja

26 Września 2024
Felisatti

Felisatti RH36 Instrukcja

25 Września 2024
Felisatti

Felisatti DMF23 Instrukcja

24 Września 2024
Felisatti

Felisatti RHF45 Instrukcja

24 Września 2024

Instrukcje Wiertarka

Najnowsze instrukcje dla Wiertarka

Ozito

Ozito BDP-500 Instrukcja

15 Października 2024
Einhell

Einhell BM-G1100 E Instrukcja

14 Października 2024
Sun Joe

Sun Joe 24V-DDK-LTX-PNK Instrukcja

14 Października 2024
DeWalt

DeWalt DWD450 Instrukcja

14 Października 2024
Black & Decker

Black & Decker GC1800 Instrukcja

13 Października 2024
Rupes

Rupes BH 252R Instrukcja

13 Października 2024
Makita

Makita HP2070 Instrukcja

13 Października 2024
Makita

Makita DHR263ZJ Instrukcja

12 Października 2024
Black & Decker

Black & Decker BDCDE120 Instrukcja

10 Października 2024
Gamma

Gamma BH-1500W Instrukcja

9 Października 2024