Instrukcja obsługi FeiyuTech G4S

FeiyuTech Niesklasyfikowane G4S

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla FeiyuTech G4S (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

OFF

18350 18350

MINI-USB

10Pin

1 2 3

Joystick

360°

°360°

For other functions

Switch operating modes

Turn on/off

The working mode and

function can be identified

by the LED status

JoystickJoystick

Video Output Cable

5Read the GoPro SD card and Charge the GoPro

GoPro Mini

Video / SD

to Micro port

reading switch

GoPro charging

switch

USB Cable

Read the GoPro SD card and

charge the GoPro without dismount

the GoPro

When the gimbal and GoPro are

powered on , connect the Analog

Monitor to the function port with

the Video Output Cable, to output

the video to the Analog Monitor.

G4S 3-Axis handheld gimbal has a mini to micro port, It can connect the GoPro with a micro usb cable. You can read the GoPro SD card and

Charge the GoPro without dismount the GoPro, and it works when the gimbal is powered off.

The GoPro charging switch and the SD card reading switch works independently, and it works when the gimbal is powered off. The default is off.

Rolling

Tilting

Panning

Function Button

（ ON / OFF ）

1/4 Inch Screw Hole

If the indicator light flashes red, the

Gimbal will not work correctly due to

Attention !

an error.

1Beginner Guide

2Product Appearance Instructions

4Video Output

Operation Instructions

Inversion Mode

When in any working mode, press the function button

for three times in succession, the Gimbal will enter into the inversion mode

and switch to the Panning Mode automatically.

Invert the Gimbal to capture more excited scenes easily by switching mode

combination. When in inversion working condition press the function button

for three times in succession to reset the Gimbal back to the original state.

Reset

Indicator Explanation

LED Status Explain

Blue light flashes

three times Full Power

Blue light flashes

twice Enough Power

Blue light flashes

once Low Power

Blue light keeps

flashing No Power

If any comments or suggestions please do not hesitate

Remove the power switch

cap, insert two 18350

batteries into the handle.

to e-mail us directly : service@feiyu-tech.com

Mount the camera carefully to

the mounting bracket and make

sure the camera is firmly connected

with the MINI-USB 10Pin.

Press the clip at both ends of the

clip, clip it as above picture.

Power On / Off

Assembly the clipMount the CameraInsert The Batteries

Joystick

You can control

the direction by

the joystick

Function

Interface

Indicator

Working Mode Instructions

Camera is permitted to pan left or right. Vertical tilts or rolls are restricted.

Camera stays in its current orientation. All panning, tilting and rolls are restricted.

Panning Mode

Camera is permitted to pan left or right and tilt up and down. Rolls are restricted. Panning and Tilng Mode

Lock Mode

Function

Interface Analog Monitor

( Equipped By Users )

Function Button

( Indicator Light )

Version 2.0

Applicable to the firmware V1.25 and above version

Power On: Single tap the function button,the

gimbal shall be powered on after 2 seconds.

Power Off: Hold down the function button for

3 seconds to turn off the gimbal.

Attention: Turn the gimbal on

after ensuring the camera is secure.

Operation

Double tap

Reset the tilting axis of the gimbal to initial orientation and initial mode

Function

Single tap

Explanation

Panning Mode / Lock Mode

Panning and Tilting Mode

Triple tap

Single tap to switch between panning mode and lock mode

Under panning and tilting mode, single tap to switch to lock mode

Inversion Mode It is possible to switch to other modes under inversion mode,

triple tap again to exit inversion mode and reset

Long press for 3 seconds Power off

Quadruple tap Reset

Tap button for six times Please refer to“Gimbal Horizontal Angle Adjustment”for operations

Single tap again to awake the gimbal, or triple tap

to initialize the gimbal

Rolling angle adjustment

Long press for 1 second Standby

LED Status Mode / Status

Single flash

Double flashes

Panning mode

Panning and Tilting mode

Lock mode / Initialize the gimbalAlways on

Flash quickly Rolling angle adjustment /

Initialization failure / Malfunction

Three flashes

Indicator

Standby

Operating Instructions of Function Button

Light

Status

Reset the tilting axis of the gimbal to initial orientation

and initial mode.

In standby model, keep the gimbal in power-up state,

the motor stops working, the indicator light flashes for

three times, and single tap again to wake the gimbal.

Standby

Other Function

!( 1 ) Please install the suitable camera first before power on the Gimbal.

( 2 ) Please turn off the power when not in use.

GND

Video

Down

Left

Down

Left

RightRight

Joystick Direction

Joystick Control

micro port

Suitable for GoPro HERO 4 / HERO 3+ / HERO 3

G4S 3-Axis Handheld Gimbal

Initialize the gimbal

Gimbal Horizontal Angle Adjustment

STEP 1

STEP 2

Tap button for six times for roll angle adjustment, the tilt

and roll angle restore to the horizontal status. Under the

roll angle adjustment state, move the joystick to the left

or to the right to adjust the roll angle, single tap again to

save the setting and exit after adjusting.

The horizontal angle needs to be adjusted

whenever the following situations happen

to the gimbal, user can adjust the horizontal

angle by gimbal initialization and joystick.

Note: Please adjust in this state

Type：18350

USB CableUSB Connector

Charger

Input: DC 5V

Rechargeable

Output: DC 4.2V

Battery

Video Output

Cable

How to Charging

USB Cable

USB Power

Adapter

（Not included）

mini port

Remote Control（Optional Item）

č Ď

Wireless

remote control

Note: The joystick and function button will be disabled after connecting with the remote control.

Receiver

for wireless

Joystick

Steps to connect wireless remote control:

remote control

Wireless Remote Control

USB Cable

Power

Panning Mode / Lock Mode

Panning and Tilting Mode

Inversion Mode

OFF

Function

Reset (Restore to the boot-up state)

Button

Operation

Long press for 0.5 second

Long press for 3 seconds

Keep the gimbal powered on, restart the remote control and

connect the receiver of RC to the gimbal, press the remote control function

button for 7 times in 5 seconds, if the indicator on the RC flashes 5 times it

means the receiver and the transmitter of RC match successfully, then

customer can control the gimbal by the RC.

▲ RC needs to be match code whenever the following situations：

（1）Connecting properly but still control in fail.

（2）Change the receiver or wireless remote control

Match Code

Left Right

Down

Wired Remote Control

Install the receiver for wireless remote control: Insert the receiver for

wireless remote control into the function port of gimbal .

Open the wireless remote control.

Open the gimbal.

Use the wireless remote control to control the gimbal.

15 meters in an open environment.

Connect the Micro interface of wireless remote control with 5V

charger(Not included) by USB cable.

Charging

Remote Control Distance

Power on / off

Please install

the receiver properly

before power on

Function

Button

Direction

Direction button

Button

of the wired remote control

Remote Control Operation Instructions

Turn Off The Gimbal and RC

Calibration Using Remote Control

Operation

Explanation

Remark

Tap Button Six Times

Match Code Mode

Match code when connecting properly but still control in fail or change

the receiver/wireless remote control.

Tap Button Seven Times

Double Tap

Single Tap

Triple Tap

Quadruple Tap

Long Press For 3 Second

StandbyLong Press For 1 Second

Wireless RC

G4S 3-Axis Handhled Gimbal is a feature-rich camera stabilizer, yet

lightweight and portable.

DISCLAIMER ATTENTION

Firmware Upgrade

USB Cable

9Specification

Upgrade........

Please visit the official website of Feiyu Tech

Standard And Optional Accessories

to get related information: www.feiyu-tech.com

Technical support: service@feiyu-tech.com

260 g (Without batteries & camera)

800 mA

3°/s ~ 150°/s

Adaption GoPro HERO 4 / HERO3+ / HERO3

Usage Time 3 ~ 5 Hours

2°/s ~ 75°/s

360°

6.0 V ~ 9 V360°

360°

Working Voltage

Overload Current Protection

Vertical Tilting Angle

Rolls Angle

Horizontal Panning Angle

Tilting Increments

Panning Increments Weight

Reset the tilting axis of the gimbal to initial orientatiozn and initial mode

Single tap to switch between panning mode and lock mode

Under panning and tilting mode, single tap to switch to lock mode

It is possible to switch to other modes under inversion mode, triple tap

again to exit inversion mode and reset

Please refer to“Gimbal Horizontal Angle Adjustment”for operations

Single tap again to awake the gimbal, or triple tap to initialize the gimbal

Tip：It will be automatically powered

off to save battery if there is no

operation within three minutes.

Adjusting steps:

( 1 ) After powering the gimbal on, hold down the function button for one second to enter

standby mode, and the LED indicator shall flash for three times;

( 2 ) Consecutively tap the function button for three times, LED indicator shall be always

on, place the gimbal on a flat surface and keep it stationary;

( 3 ) When the initialization is completed, the LED indicator will flash for three times.

Afterward pick up the gimbal and single tap to awake the gimbal.

Initialize the gimbal

（1）The tilt angle is not leveled with the horizontal

surface.

（2）The roll angle is not parallel to the horizontal

surface.

（3）Under lock mode, the panning angle drifts. When the initialization failed, the LED indicator will flash quickly, repeat step (2) & (3)

to reinitialize.

After finished the , the rolling angle still not parallel to the horizontal surface,

you can use the joystick to adjust the rolling angle according to .

STEP 1

Rolling angle adjustment

STEP 2

Please assemble the gimbal in accordance to the diagram provided .

Please upgrade the firmware and configuration settings with the

provided USB data cable.

Please charge the battery with the provided battery charger.

Please install the camera securely before powering on the gimbal.

When the gimbal is not in use or placed on the table, please

ensure it is powered off.

Function

Interface

Function

Interface

Function

Interface

Attention !

Make sure that the

connection to the

computer is done by the

USB Connector

Upgrade steps

(1) Download and install the USB driver and the software for updating and the latest firmware

from www.feiyu-tech.com

Connect the USB cable to mini port as the diagram. Attention please use the USB connector.

Please update the firmware as the manual.

(2)

(3)

Prohibit any user for any illegal purpose. Users will be responsible for

all behaviors of purchase and use products.

The Company assumes no liability for any risks related to or resulting

from the debug and use of this product (including the direct, indirect or

third-party losses).

For any unknown sources of using, we will not be at any services.

Feiyu Tech reserves the right to amend this manual and the terms and

mini port

conditions of use the gimbal at any time.

micro port

Everyone

Can Make a Movie

Specyfikacje produktu

Marka:	FeiyuTech
Kategoria:	Niesklasyfikowane
Model:	G4S

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z FeiyuTech G4S, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Niesklasyfikowane FeiyuTech

FeiyuTech MG Lite Instrukcja

3 Października 2024

FeiyuTech G4S Instrukcja

3 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024

Stihl HT 70 Instrukcja

15 Października 2024

Ernesto H14270 Instrukcja

15 Października 2024

Uniden BT MIC KIT Instrukcja

15 Października 2024

Vaude Omnis Bike 26 Instrukcja

15 Października 2024

ART ProChannel II Instrukcja

15 Października 2024

Aukey DR02J Instrukcja

15 Października 2024

Master Lock 653EURD Instrukcja

15 Października 2024

Roland FR-18 Diatonic Instrukcja

15 Października 2024