Instrukcja obsługi Extron MLC 104 IP Plus L

Extron Zdalne sterowanie MLC 104 IP Plus L

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Extron MLC 104 IP Plus L (16 stron) w kategorii Zdalne sterowanie. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/16
Global Confi gurator 2.2,
MLC 226/104 Confi guration Program 3.1.1, and
System 5 IP Confi guration Program 3.1.1
Upgrade Guide
68-1313-01 Rev. A
08 06
PRELIMINARY
1
Global Configurator, Windows-based Control Programs
PRELIMINARY
Introduction
This installation guide provides step by step instructions on how to
• Upgrade to Global Configurator 2.2
• Upgrade from GC 2.0.x
• Upgrade from GC 2.1.x
• Upgrade to MediaLink 226/104 or System 5 IP Configuration Software 3.1.1
• Upgrade the System 5 IP with patch firmware (This includes information on how
to )retain IP settings after upgrading from version 1.0x to 2.00.
If you encounter problems with the following upgrades, please keep in mind that
Extron Technical Support (http://www.extron.com/company/contactus.asp) is only
a phone call or a few mouse clicks away.
Upgrading to Global Configurator 2.2: a Checklist
Prior to upgrading your existing Global Configurator (GC) project to GC 2.2, ensure
that the following four elements are present on your system.
cThe Global Configurator project file
For GC 2.0.x
• Original project files
For GC 2.1.x
• Original project files or
• Import a compressed project file (.gcc) or
• Import the file from an IP Link device
cThe Extron serial and IR drivers used in the project file
These drivers can be found
• On the Extron Web site (http://www.extron.com/iplinkdrivers)
• Via the Driver Subscription feature of GC 2.2
• Via the IR Learner software's user-defined IR drivers (.eir)
N Defective device drivers are routinely removed from the Extron Web site, so you
may find that some drivers are missing. Most of these drivers are replaced with
newer versions.
If a required device driver is missing after you open your project in GC 2.2, and
it cannot be found on the Extron Web site, search for an updated version of the
driver. When the correct driver is found, you must upgrade it for every IP Link
device in your network.
cThe minimum firmware version for the MLC products
Global Configurator 2.2 requires the following minimum firmware
versions. Any IP Link device with an earlier version requires a firmware
upgrade. This firmware can be obtained from the Extron Web site
(http://www.extron.com/iplinkdrivers).
• MLC 104 Series, version 1.03
• MLC 104 IP Series, version 1.03
• MLC 226 IP Series, version 1.05
N For IP Link devices that reside on a network, firmware can be easily upgraded
using IP Link File Manager 1.1.3 or later.
PRELIMINARY
Upgrade Guide, cont’d
Global Configurator, Windows-based Control Programs
2
PRELIMINARY
N If a firmware update is needed, execute the command after the EscZY reset
firmware is updated. See the firmware’s release notes for instructions.
cThe minimum firmware version for the System 5 IP products
Global Configurator 2.2 requires the following minimum firmware
version. Any IP Link device with an earlier version requires a firmware
upgrade. This firmware can be obtained from the Extron Web site
(http://www.extron.com/firmware).
System 5 IP Series, version 2.00
N For instruction on how to retain your System 5 IP settings when upgrading
the firmware from version 1.0x to 2.00, please refer to the System 5 IP Patch
Firmware Upgrade section.
c IP Link devices that are online
Upgrading to Global Configurator 2.2 requires that all IP Link devices
be online to successfully upload the configuration.
N When uploading files to devices, please note that any customized GlobalViewer
(GV) files, including those placed in the GC2 directory of an IP Link device,
must be uploaded the GC 2.2 upload process is complete. after
Upgrading from GC 2.0.x
Upgrading from Global Configurator (GC) 2.0 requires the original project file
(.gc2) and all of its device configuration files (.xml). The Import File option cannot
be used for this configuration.
Step 1: Open the GC project file.
1. Open the Global Configurator file by choosing from the menu Open... File
and choosing the file.
The following message box appears.
2. Click .OK
Step 2: Rebuild all devices in the configuration
1. From the menu, choose . The Upload Manager Build Build All Configurations
appears when the build is complete.
2. On the Upload Manager window, click .Begin
3. Click when the upload is complete.Close
Using this rebuild option saves your project in the new GC 2.2 format.
PRELIMINARY

Specyfikacje produktu

Marka: Extron
Kategoria: Zdalne sterowanie
Model: MLC 104 IP Plus L

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Extron MLC 104 IP Plus L, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Zdalne sterowanie Extron

Extron

Extron IR 501 Instrukcja

8 Października 2024
Extron

Extron MLC 104 IP Plus AAP Instrukcja

8 Października 2024
Extron

Extron TLP 710TV Instrukcja

8 Października 2024
Extron

Extron TLP 1000TV Instrukcja

8 Października 2024
Extron

Extron TLP 350MV Instrukcja

8 Października 2024
Extron

Extron MLC 104 IP Plus Instrukcja

8 Października 2024
Extron

Extron MLC 104 IP Plus L Instrukcja

8 Października 2024

Instrukcje Zdalne sterowanie

Najnowsze instrukcje dla Zdalne sterowanie

Neewer

Neewer RT112 Instrukcja

9 Października 2024
Neewer

Neewer RT113 Instrukcja

9 Października 2024
Zalman

Zalman ZM-VE350 Instrukcja

9 Października 2024
Canon

Canon BG-R20 Instrukcja

9 Października 2024
Canon

Canon BG-R20EP Instrukcja

9 Października 2024
Mosconi

Mosconi DSP6T8 Instrukcja

8 Października 2024
Mosconi

Mosconi RC MINI Instrukcja

8 Października 2024
Ridem

Ridem CRC UNB Instrukcja

8 Października 2024
Ridem

Ridem CRC UNW Instrukcja

8 Października 2024
ORNO

ORNO OR-GB-458 Instrukcja

8 Października 2024