Instrukcja obsługi Extron DA HD 8K L

Extron odbiornik DA HD 8K L

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Extron DA HD 8K L (2 stron) w kategorii odbiornik. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
1
DA4 HD 8K L and DA6 HD 4K L • Setup Guide
IMPORTANT NOTE:
Go to www.extron.com for the complete user guide, installation instructions, and specications before connecting
the product to the power source.
This guide provides basic instructions for an experienced technician to install the DA HD 8K L distribution ampliers.
Overview
The Extron DA4 HD 8K L and DA6 HD 8K L distribution ampliers distribute one HDMI input signal to four or six outputs
simultaneously at resolutions up to 8K @ 30 Hz 4:4:4 or 8K @ 60 Hz 4:2:0, and comply with HDMI 2.1 and HDCP 2.2. The DAs also
feature EDID Minder® Plus, remote control and monitoring via Ethernet, USB, or RS-232, and discrete display control via CEC.
For complete instructions, see the DA HD 8K L Series User Guide at www.extron.com.
Front Panel
DA4 HD 8K L
CONFIG
INPUT 1
SIGNAL
HDCP
e
2 3 4
OUTPUTS
DA6 HD 8K L
CONFIG
INPUT 1
SIGNAL
HDCP
e
2 3 4 5 6
OUTPUTS
A
A
A
A
A
A C
C
C
C
C
CB
B
B
B
B
B D
D
D
D
D
D
A — Lights when power is applied to the unit.Power status LED
B USB-C Config port — Connect a PC to this port to configure and monitor the DA via Simple Instruction Set (SIS™ ™) or
Product Configuration Software (PCS).
C — Input LEDs
• Signal LED — Lights when a TMDS signal is detected on the HDMI input. If the source requires HDCP encryption, this LED
may light only when HDCP is authenticated.
• HDCP LED — Lights when the source requires HDCP encryption and it has been authenticated with the HDMI input.
D — Outputs LEDs
• HDCP LEDs — Light when HDCP is authenticated between a DA output and the corresponding sink device.
• Signal LEDs — Light when HPD is detected from the corresponding sink device and a TMDS signal is detected at the
input.
Rear Panel
POWER
12V
--A MAX 21 43
INPUT
REM O T E
OUTPU T S
LAN
RS-232
T x R x G
R
POWER
12V
--A MAX 21 63 4 5
INPUT
REM O T E
OUTPU T S
LAN
RS-232
T x R x G
R
D
D
D
D
D
D
A
A
A
A
A
A B
B
B
B
B
BE
E
E
E
E
E F
F
F
F
F
F
C
C
C
C
C
C
A Power input — Connect the provided 12 VDC, 3.0 A power supply to this 2-pole 3.5 mm captive screw port (see the power
Attention and diagram to wire the connector on ).page 2
2
68-3435-50 Rev. A
08 24
SECTION A–A
Ridges
Smooth
A
A
3/16"
(5 mm) Max.
POWER
12V
--A MAX ATTENTION:
• Do not connect the power supply before reading the
Attention in the Power Supply section of the DA HD 8K L
Series User Guide.
• Ne branchez pas la source d’alimentation externes
avant d’avoir lu les mises en garde dans la section
« Power Supply » du DA HD 8K L Series User Guide.
B (see on page 1HDMI input Rear Panel ) — Connect a source device to this female HDMI type A input.
C HDMI outputs — Connect up to four or six display devices to these female HDMI type A outputs.
D Remote RS-232 port — Connect the provided 3-pole captive screw connector for SIS configuration, monitoring, and firmware
updates (Pin 1 = Tx, Pin 2 = Rx, Pin 3 = Ground). Protocol: 9600 baud, 8 data bits, 1 stop bit, no parity.
E LAN port — Connect to an Ethernet LAN or WAN via this RJ-45 port to control the DA from a remote location. When connected
to an Ethernet LAN or WAN, the DA can be accessed and operated from a computer with a standard internet browser.
Ethernet connection indicators — The Link and Activity LEDs indicate the status of the Ethernet connection.
• Green Link LED — Indicates the distribution amplier is properly connected to an Ethernet LAN. This LED lights steadily.
• Amber Activity LED — Indicates transmission of data packets on the RJ-45 port. This LED ickers as the distribution
amplier communicates.
F Reset button — Use an Extron Tweeker or small screwdriver to press and hold the button while the DA is running or while
powering up, for different reset levels.
• Press and hold the reset button while applying power to revert to factory default rmware for a single power cycle, but
maintain IP settings.
• Press and hold the reset button for 3 seconds and again for <1 second within 1 second to reset the unit to factory settings.
• Press and hold the reset button for 6 seconds and again for <1 second after the LED blinks twice to reset all IP settings
back to factory defaults.
• Press and hold reset button for 9 seconds and again for <1 second after the LED blinks 3 times to reset all settings to
default except the rmware.
Installation
1. Mount the DA in a suitable location with one of the recommended mounting kits (see www.extron.com for mounting options).
Follow the instructions provided with the mounting kit.
2. If required, connect a control PC to the USB-C Cong port (see Front Panel,
B on page 1), Remote RS-232 port (see Rear
Panel, D, see the diagram below for wiring), or LAN port (E, see the diagram below, right for wiring).
RS-232
Tx Rx G
REMOTE
TransmitReceive
ReceiveTransmit
GroundGround
DB9 Pin Locations
Female
5 1
9 6
Pin 2 = Rx
Pin 3 = Tx
Pin 5 = G
Computer DA HD 8K
NOTE: Use PCS to congure EDID Minder, mute the video signal, mute the
audio signal, adjust the video color bit depth, or monitor the signal and
HDCP status (see the DA HD 8K L Series Help File).
3. Connect the display devices to the rear panel HDMI outputs (see Rear Panel,
C)
and power them on.
123 45678
RJ-45 Connector
Insert Twisted
Pair Wires
Pins:
Pin
1
2
3
4
5
6
7
8
Wire color
White-green
Green
White-orange
Blue
White-blue
Orange
White-brown
Brown
Wire color
T568A T568B
White-orange
Orange
White-green
Blue
White-blue
Green
White-brown
Brown
4. Connect the source device to the rear panel HDMI input (
B).
NOTE: Use the LockIt® HDMI cable lacing brackets provided to secure the HDMI connectors.
5. Connect the provided 12 VDC, 3.0 A power supply to the 2-pole captive screw inlet (
A, see the diagram at the top of the page
to wire the connector).
6. Power on the source device.
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the Extron
Safety and Regulatory Compliance Guide on the Extron website.
© 2024 Extron — All rights reserved. www.extron.com
All trademarks mentioned are the property of their respective owners.
Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876

Specyfikacje produktu

Marka: Extron
Kategoria: odbiornik
Model: DA HD 8K L

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Extron DA HD 8K L, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje odbiornik Extron

Extron

Extron XTP R HWP 201 4K Instrukcja

9 Października 2024
Extron

Extron DP DA2 Instrukcja

9 Października 2024
Extron

Extron DA HD 8K L Instrukcja

9 Października 2024
Extron

Extron XTP SFR HD 4K Instrukcja

9 Października 2024
Extron

Extron XPA U 1002 Instrukcja

9 Października 2024
Extron

Extron XPA U 2004 FX Instrukcja

9 Października 2024
Extron

Extron XPA U 1004 SB Instrukcja

9 Października 2024
Extron

Extron XPA U 358 Instrukcja

9 Października 2024
Extron

Extron XPA U 358C Instrukcja

9 Października 2024
Extron

Extron XPA U 758 Instrukcja

9 Października 2024

Instrukcje odbiornik

Najnowsze instrukcje dla odbiornik

Denon

Denon AVR-S900W Instrukcja

15 Października 2024
Pro-Ject

Pro-Ject Amp Box DS2 Instrukcja

15 Października 2024
AKG

AKG HP12U Instrukcja

15 Października 2024
Apart

Apart SBR160 Instrukcja

14 Października 2024
American Audio

American Audio VLP 600 Instrukcja

14 Października 2024
Chord

Chord Anni Instrukcja

14 Października 2024
Sennheiser

Sennheiser EM 9046 SU Instrukcja

14 Października 2024
Yamaha

Yamaha MusicCast RX-V481 Instrukcja

13 Października 2024
JL Audio

JL Audio VX600/6i Instrukcja

12 Października 2024
Pioneer

Pioneer SX-303RDS Instrukcja

10 Października 2024