Instrukcja obsługi Extech 42270

Extech Sprzęt pomiarowy 42270

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Extech 42270 (1 stron) w kategorii Sprzęt pomiarowy. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/1
User's Guide
Model 42270 Temperature & Humidity Datalogger
Model 42260 Temperature Datalogger
Introduction
Congratulations on your purchase of the Extech Datalogging Module. The following
models are covered in this manual.
Model 42270: Temperature and Humidity Datalogging Module
Model 42260: Temperature-only Datalogging Module
The Dataloggers can be used to monitor the temperature of greenhouses,
warehouses, food transports, aircraft cabins, refrigerated trucks, containers,
museums, and HVAC equipment. The Model 42270 records Relative Humidity
readings in addition to temperature readings. Instructions on how to program the
dataloggers are not included this manual. Programming and data retrieval
instructions are included in the 42275, 42265, 42276 and 42266 kits.
Description
1. Mounting hole
2. Status LEDs (Record and Alarm)
3. LCD display
Displays
LCD Display
REC: Displayed while logging readings.
HI and LOW: Displayed when the High or Low Alarm limit is exceeded.
RH%: Relative Humidity (42270 only)
C or F: Temperature units.
COMM: Appears when Datalogger is communicating with a PC.
Recording Status Indication
Both the RED status LED and the display indicator ‘REC’ will ash every 5 seconds if
the sampling rate is set to 5 seconds or higher. If the sampling rate is set lower than 5
seconds, the indicators will ash every 1, 2, 3, or 4 seconds as programmed.
ALARM Status Indication
Both the YELLOW status LED and the display indicator ‘ALM’ will ash when the
recorded value is higher than the user programmed High Alarm value or lower than the
Low Alarm value. The Alarm status LED and the ‘ALM’ display indicator flash every 5
seconds if the sampling rate is programmed for 5 seconds or higher. If the sampling
rate is set lower than 5 seconds, the indicators will ash every 1, 2, 3, or 4 seconds as
programmed.
Low Battery Indication
When the lithium battery voltage nears the critical operating level, the LCD displays
‘LO’. To replace the battery, refer to the Battery Replacement section of this manual.
Specications
Front panel status LEDs Two (2): RECORD and ALARM
Temperature range -40 to 85°C (-40 to 185°F)
Temperature resolution 0.1° up to 99.9°; 1° from 100° to 185°
Temperature accuracy ±0.6°C (1.2°F) from -20 to 50°C (-4 to 122°F)
±1.2°C (2.4°F) all other ranges
Humidity range & accuracy 0.0 to 99.9% Relative Humidity; Accuracy: ± 3%
Datalogger Memory 16,000 temperature readings (8,000 temperature and
8,000 humidity readings on the 42270)
Sampling rate Programmable from 1 to 7200 seconds (2 hours)
Power supply One 3.6V ½ ‘AA’ lithium battery
Battery Life 1 year: 5 second sample rate in sleep mode
3.8 months: 24 hour sample rate in non-sleep mode
Low battery Indicator Display shows ‘LO’
Dimensions 76.2 x 57.2 x 22.3mm (3 x 2.3 x 0.88")
The datalogger display will not switch on
until activated by software or the printer
programmer.
THESE DATALOGGERS CANNOT BE USED WITHOUT THE
SOFTWARE FROM KIT 42275 (42265) OR THE PRINTER
PROGRAMMER 42276 (42266).
Battery Replacement
When the low battery icon (‘LO’) appears on the LCD display, replace the Lithium CR2
battery.
1. Open Datalogger housing by rst removing the four (4) rear Phillips screws.
2. Carefully pry off the rear of the Datalogger.
3. The cylindrical lithium battery is located on the bottom of the PCB board.
4. Replace the battery, observing polarity.
5. Assemble the Datalogger housing.
You, as the end user, are legally bound (Battery ordinance) to return all
used batteries and accumulators; disposal in the household garbage
is prohibited!
You can hand over your used batteries / accumulators at collection
points in your community or wherever batteries / accumulators are sold!
Disposal: Follow the valid legal stipulations in respect of the disposal of
the device at the end of its lifecycle
Copyright 2008 Extech Instruments Corporation©
All rights reserved including the right of reproduction in whole or in part in any form.
42270_42260-EU-EN V2.2 7/09

Specyfikacje produktu

Marka: Extech
Kategoria: Sprzęt pomiarowy
Model: 42270

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Extech 42270, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Sprzęt pomiarowy Extech

Extech

Extech 44550 Instrukcja

18 Marca 2025
Extech

Extech CO15 Instrukcja

30 Stycznia 2025
Extech

Extech 380941 Instrukcja

8 Stycznia 2025
Extech

Extech 380926 Instrukcja

8 Stycznia 2025
Extech

Extech PRC20 Instrukcja

8 Października 2024
Extech

Extech PRC30 Instrukcja

8 Października 2024
Extech

Extech SD900 Instrukcja

8 Października 2024
Extech

Extech PRC15 Instrukcja

8 Października 2024
Extech

Extech 412300A Instrukcja

8 Października 2024
Extech

Extech 412400 Instrukcja

8 Października 2024

Instrukcje Sprzęt pomiarowy

Najnowsze instrukcje dla Sprzęt pomiarowy

BAXTER

BAXTER WM600C Instrukcja

22 Marca 2025
PCE Instruments

PCE Instruments PCE-RDM 5 Instrukcja

14 Marca 2025
PCE Instruments

PCE Instruments PCE-STM 5 Instrukcja

14 Marca 2025
PCE Instruments

PCE Instruments PCE-313 S Instrukcja

14 Marca 2025
Sauter

Sauter TVL-O Instrukcja

10 Marca 2025
Sauter

Sauter TVM 20KN120N-LB Instrukcja

10 Marca 2025
Sauter

Sauter TVL-E Instrukcja

10 Marca 2025
Panasonic

Panasonic BE-A301P Instrukcja

10 Marca 2025
Panasonic

Panasonic BE-A201P Instrukcja

10 Marca 2025
Panasonic

Panasonic BE-A401P Instrukcja

10 Marca 2025