Instrukcja obsługi Etna EN4480

Etna Okap wyciągowy EN4480

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Etna EN4480 (24 stron) w kategorii Okap wyciągowy. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/24

COOKER HOOD

USER INSTRUCTIONS

DUNSTABZUGSHAUBE

GEBRAUCHSANWEISUNG

HOTTE PER CUISINE

MANUEL DUTILISATION

GEBRUIKSAANWIJZING

AFZUIGKAP

MANUAL DE UTILIZACION

CAMPANA EXTRACTORA

MANUAL DO USUÁRIO

CAPPA ASPIRANTE

MANUALE DUSO

BRUKSANVISNING

VENTILATOR

BRUKERVEILEDNING

EMHÆTTE

BRUGERVEJLEDNING

LIESITUULETIN

KÄYTTÖOHJE

ODHGIES CRHSEWS

OKAPA

INSTRUKCJE UZYTKOWNIKA

ODSAVAC

NÁVOD K POÙZITÌ

PARAELSZIVÓ

HASZNÁLATI ÚTMUTATÓ

DEU

FRA

NLD

ESP

ITA

PRT

SVE

NOR

GRC

RUS

POL

CZE

HUN

ARE

FIN

DNK

âûòÿæêà

COIFA ASPIRANTE

OPORROFHTHRAS

ÈÍCÒÐÓÊÖÈÈ ÏO ÝÊÑÏËÓÀÒÀÖÈÈ

GBCDEA

ABCDE

75 -100 588

cm 75 Min 663 : Max 1163

Max 500

cm 100 Min 688 : Max 1188

340

235

330150 150

203

Fig.3

Fig.2

Fig.5

Fig.5A

Fig.5B

Fig.5C

Fig.1 Fig.4

ABCDEF

GENERAL

Carefully read the following important information regarding

installation safety and maintenance. Keep this information booklet

accessible for further consultations.

The appliance has been designed as a exhausting version (external

exhaust) or as a filter version (internal air recycle) cooker hood.

SAFETY PRECAUTION

• Take care when the cooker hood is operating simultaneously with an

open fireplace or burner that depend on the air in the environment and

are supplied by other than electrical energy, as the cooker hood removes

the air from the environment which a burner or fireplace need for

combustion.

The negative pressure in the environment must not exceed 4 Pa (4 x 10

–5 bar).

Provide adequate ventilation in the environment for a safe operation of

the cooker hood.

Follow the local laws applicable for external air evacuation.

• WARNING!!

In certain circumstances electrical appliances may be a danger

hazard.

A) Do not check the status of the filters while the cooker hood

is operating

B) Do not touch the light bulbs after appliance use

C) Flambè cooking is prohibited underneath the cooker hood

D) Avoid free flame, as it is damaging for the filters and a fire

hazard

E) Constantly check food frying to avoid that the overheated oil

may become a fire hazard

F) Disconnect the electrical plug prior to any maintenance.

INSTALLATION INSTRUCTIONS

• Electric Connection

The appliance has been manufactured as a class II, therefore no earth

cable is necessary.

The connection to the mains is carried out as follows:

BROWN = L line

BLUE = N neutral

If not provided, connect a plug for the electrical load indicated on the

description label. Where a plug is provided, the cooker hood must be

installed in order that the plug is easily accessible.

An omnipolar switch with a minimum aperture of 3mm between contacts,

in line with the electrical load and local standards, must be placed

between the appliance and the network in the case of direct connection

to the electrical network.

• The appliance must be installed at a minimum height of 650mm

from cooker stove.

If a connection tube composed of two parts is used, the upper

part must be placed outside the lower part.

Do not connect the cooker hood exhaust to the same conductor

used to circulate hot air or for evacuating fumes from other

appliances generated by other than an electrical source.

• Mounting the cooker hood to the wall

Drill holes A-C-D according to indications quoted in (fig. 3).

Use screws and screw anchors suitable for wall (e.g. reinforced cement,

plasterboard) for the mounting of the cooker hood.

Where screws and screw anchors are supplied ensure that they are

suitable for the type of wall where the cooker hood is to be mounted.

Lock in the flange connector Y to the cooker hood (fig. 2).

Affix the bracket Z to the wall via the drill holes A

Hang the cooker hood on the wall using the drill holes C.

Fasten the cooker hood using the fastening drill holes D.

• Exhausting version

Connect the flange Y to the discharge opening with a connecting tube

(do not carry out for filter version).

Insert the upper exhausting of the chimney E inside the lower section F.

Fix the lower of the chimney tothe hood by the screws H supplied (fig.

2). Pull out the upper section up to bracket Z and fix the screws L (fig.

2)In order to transform your cooker hood from suction version to filter

version, ask your local retailer for active carbon filters and then carry

out instructions for mounting filter version cooker hood.

• Filter Version

Install the cooker hood and the two connectors as described in the

paragraph mounting the exhausting version cooker hood.

To mount the filter connector refer to instructions included in the kit.

If the kit is not supplied, then order the kit as an accessory from your

local dealer.

The filters must be fitted to the fan unit placed inside the cooker hood.

The air is replaced in the environment via the eyelets impressed on the

connector E.

USE AND MAINTENANCE

• It is recommended to operate the appliance prior to cooking.

It is recommended to leave the appliance in operation for 15 minutes

after cooking is terminated in order to completely eliminate cooking

vapours and odours.

The proper function of the cooker hood is conditioned by the regularity

of the maintenance operations, in particular, the active carbon filter.

• The anti-grease filters capture the grease particles suspended in the

air, and are therefore subject to clogging according to the frequency

of the use of the appliance.

In order to prevent fire hazard, it is recommendable to clean the filter

at a maximum of 2 months by carrying out the following instructions:

- Remove the filters from the cooker hood and wash them in a solution

of water and neutral liquid detergent, leaving to soak.

- Rinse thoroughly with warm water and leave to dry.

- The filters may also be washed in the dishwasher.

The aluminium panels may alter in colour after several washes. This

is not cause for customer complaint nor replacement of panels.

• The active carbon filters purify the air that is replaced in the environment.

The filters are not washable nor re-useable and must be replaced at

maximum every four months. The saturation of the active carbon filter

depends on the frequency of use of the appliance, by the type of cooking

and the regularity of cleaning the anti-grease filters.

• Clean the fan and other surfaces of the cooker hood regularly using

a cloth moistened with denatured alcohol or non abrasive liquid

detergent.

• COMANDS: (Fig.5A) LUMINOUS_(Fig.5B) MECHANICAL the

key symbols are explained below:

A = LIGHT

B = OFF

C = SPEED I

D = SPEED II

E = SPEED III

F = AUTOMATIC STOP TIMER - 15 minutes

G= MOTOR WORKING indicator

(Fig. 5C) DISPLAY:

Push-button A = on/off lights switch

Push-button B = on/off cooker hood switch. The appliance switches on

at speed level 1, If the cooker hood is on depress the push-button for ½

a second to switch off the cooker hood. If the cooker hood is at speed level

1 it will not be necessary to depress the push-button to switch the cooker

hood off. Decreases the motor speed.

Display C = indicates the motor speed level selected and activates the

timer.

Push-button D = switches on the cooker hood. Increases the motor

speed. Depressing the push-button for 1 about second initiates the

intensive speed level for 10’ [minutes] and then returns to the speed level

prior to activation of this function.

Push-button E = Timer, when active should be visible via the decimal

point flashing in the Display “C”. Depressing the push-button when the

cooker hood is in the off mode will switch on the appliance at the first speed

level for 15’ [minutes]. The Timer switches the cooker hood off completely

(lamps and motor) after 15’ [minutes].

E.g.: if the lamps only switch on, and the timer switch is depressed then

the lamp will turn off after 15’ [minutes]. To deactivate the timer depress

the push-button a second time (twice).

The "Automatic stop timer" delays stopping of the hood, which will

continue functioning for 15 minutes at the operating speed set at the

time this function is activated.

THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR

EVENTUAL DAMAGES CAUSED BY BREACHING THE ABOVE

WARNINGS.

ENGLISH

Specyfikacje produktu

Marka:	Etna
Kategoria:	Okap wyciągowy
Model:	EN4480

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Etna EN4480, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Okap wyciągowy Etna

Etna HF2019 Instrukcja

15 Października 2024

Etna AB260RVS Instrukcja

7 Października 2024

Etna AB290ZT Instrukcja

4 Października 2024

Etna AB791RVS Instrukcja

30 Września 2024

Etna AB791ZT Instrukcja

30 Września 2024

Etna AB390ZT Instrukcja

30 Września 2024

Etna 4436 Instrukcja

24 Września 2024

Etna A4429RVS Instrukcja

17 Września 2024

Etna AD570ZT Instrukcja

13 Września 2024

Etna A4515L Instrukcja

10 Września 2024

Instrukcje Okap wyciągowy

Najnowsze instrukcje dla Okap wyciągowy

Pelgrim ISW990 Instrukcja

15 Października 2024

PKM 6080X Instrukcja

15 Października 2024

M-System MSPK 761 IX Instrukcja

15 Października 2024

Pelgrim ISWA991RVS Instrukcja

15 Października 2024

Pelgrim ISW751RVS Instrukcja

15 Października 2024

Pelgrim ISW771RVS Instrukcja

15 Października 2024

Amana WVW53UC6HV Instrukcja

15 Października 2024

Haier HPH60IMB2 Instrukcja

15 Października 2024

Haier HC60BMB2 Instrukcja

15 Października 2024

Haier HPH90IMB2 Instrukcja

15 Października 2024