Instrukcja obsługi Ernitec ELECTRA-S-04

Ernitec przełącznik ELECTRA-S-04

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Ernitec ELECTRA-S-04 (4 stron) w kategorii przełącznik. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/4
© 2015 Ernitec. All rights reserved
www.ernitec.com
Ernitec
Tempovej 41
2750 Ballerup
Denmark
Follow us on
Professional Surveillance Solutions
Electra
by
Manual
Electra S04
© 2015 Ernitec. All rights reserved
www.ernitec.com
Ernitec
Tempovej 41
2750 Ballerup
Denmark
Follow us on
Manual Electra S09 V011016
Introduction
Power- -over Ethernet (PoE) eliminates the need to run DC power to other devices on a single wired
LAN. Using Power- -Over Ethernet, installers only need to run a single CAT 5cable carries that both
data and power to each device. This allows flexibilliy greater in the location of the network
devices. And in many cases significantly decreases the installation costs.
There are two system components in the PSE (Power Sourcing Equipment) and the PD PoE –
(Powered Device). The IEEE 802.3af/at specification defines PSE as a device that inserts power
onto an Ethernet cable. The PSE may be located at the switch (Endspan configuration). Or it may
be a separate device (Poe Injector) located between the switch and the PD (Midspan
configuration). The PD is the natural termination of this link, receiving the power and the data
And it could be an IP camera or an IP phone or a WLAN Access Point that require power.
The current is transmitted over 2 of the 4 twisted pairs of wires in a Category 5, 6, 7 cable.-
Power- -over Ethernet follows the IEEE 802.3af/at specification and is completely compatible
with existing Ethernet switches and networked devices. Because the Power Sourcing Equipment
(PSE) tests whether a networked device is PoE-capable, power is never transmitted unless a
Powered Device is at the other end of the cable. It also continues to monitor the channel. If the
Powered Device does not draw a minimum current, because it has been unplugged or physically
turned off, the PSE shuts down the power to that port.
Optionally, the standard permits Powered Devices to signal th the PSEs exactly how much power
they need.
The PoE switch is a multi-port fast Ethernet switch that can be used to build high-performance
switched workgroup networks. This switch is a store- -and forward device that offers low latency for
high-speed networking. It also features a “store- -and forward” switching scheme that allows the
switch to auto-learn and store source addresses in a 8K-entry MAC address table. The switch is
targeted at workgroup, department or backbone computing environments.
© 2015 Ernitec. All rights reserved
www.ernitec.com
Ernitec
Tempovej 41
2750 Ballerup
Denmark
Follow us on
Manual Electra S04 V011016
Hardware Description
The Front Panel:
The front panel constists of LED Indicationes and 5 auto ports-sensing
4 x 10/100 Ports and 1 X 10/100 PoE Uplink port
LED Indicators:
Per Device: Power
Per Port: LINK/ACTY (Link activity)
Per PoE Port: Poe (On or off)
Figure 2. Front panel view of LED indications
Figure 2
LED
Status
Color
Description
Power
On
Green
The switch is supplied with suitable power
LINK/ACT
ON
Green
The port is
connecting
Blinks
-
The port is
recieving or transmitting data
Off
-
The port is not
linked successfully with the device
PoE
On
Green
PD is
connected
Of
-
No PD is
connected or the device does not need power

Specyfikacje produktu

Marka: Ernitec
Kategoria: przełącznik
Model: ELECTRA-S-04

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Ernitec ELECTRA-S-04, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje przełącznik Ernitec

Ernitec

Ernitec ELECTRA-S-24F Instrukcja

22 Września 2024
Ernitec

Ernitec ELECTRA-S-04 Instrukcja

20 Września 2024

Instrukcje przełącznik

Najnowsze instrukcje dla przełącznik

Powerfix

Powerfix PSSS 2 A1 Instrukcja

14 Stycznia 2025
INOGENI

INOGENI CAM230 Instrukcja

14 Stycznia 2025
Schneider

Schneider CCT15225 Instrukcja

14 Stycznia 2025
Luxul

Luxul XMS-5248P Instrukcja

14 Stycznia 2025
Luxul

Luxul AMS-2624P Instrukcja

14 Stycznia 2025
Luxul

Luxul XGS-1005 Instrukcja

14 Stycznia 2025
Luxul

Luxul AGS-1008M Instrukcja

14 Stycznia 2025
Luxul

Luxul XMS-1208P Instrukcja

14 Stycznia 2025
Luxul

Luxul XMS-7048P Instrukcja

14 Stycznia 2025
Luxul

Luxul AMS-2600 Instrukcja

14 Stycznia 2025