Instrukcja obsługi Erica Synths Black MIDI-CV

Erica Synths nieskategoryzowany Black MIDI-CV

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Erica Synths Black MIDI-CV (2 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 11 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
GLIDE
BLACK MIDI-CV
CV2 GATE2
GATE1CV1
CLK MOD
1 VOICE
2 VOICE
THANK YOU FOR PURCHASING
ERICA SYNTHS BLACK SERIES
MODULE!
Erica Black Series include high‑end,
unique functionality and superior
quality modules. Only the best,
highest quality components are
used, all inputs and outputs are
protected against undesired
overvoltage. When designing Black
Series, we put design and usability
superior. Big knobs are assigned to
key functions of the module, which
makes Black Series ideal for live
performances. Enjoy!
Erica Synths Black MIDI-CV
is compact, highly accurate and
easy to use duophonic MIDI
interface. It emulates classical
monophonic and duophonic
synth behaviour, as well as can
be configured for use in two
independent MIDI channels. Bonus
features – MIDI clock output
and analogue glide circuit on
both channels.
FEATURES:
Two CV and Gate outputs
MIDI clock output (4ppq –
sequencer friendly)
Configurable MOD output –
modulation wheel or velocity
Analogue glide on both MIDI
channels
One or two MIDI channel
configuration
One or two voice switch
SPECS:
CV range ....................................... 0‑8V
Max CV deviation 0.001V; 1cent ..........
Gate and Clock level .......................5V
Glide time ....................................0 – 2”
Power consumption +40mA, ‑9mA ....
Module width ................................6HP
Module depth ........................... 30mm
Use this knob to set
the glide time on the
output CV! It aects both
channels simultaneously
This is 4ppq Clock
output – ready to control
your sequencers. In two
MIDI channel mode
make sure, only one MIDI
device has MIDI clock
activated
These are CV outputs.
In one voice mode CV2
duplicates CV1, in two
voice mode CV2 is highest
note priority; CV1 – lowest
note priority
This in MIDI activity and
configuration indictor LED
This is MIDI input
In one MIDI channel
mode you can select
between one voice mode
(highest note priority) or
two voice mode (lowest
and highest note priority)
Push PROGRAMM button
promptly to send MIDI
panic message. Push and
hold the button and you
will enter configuration
mode. Please, refer
to the table below on
configuration settings
This is Gate output of the
first channel
This is Modulation CV
output. You can configure
it for modulation wheel
CV output or key velocity.
Refer to the table below!
This is Gate output of
the second channel.
Classic mono‑ duophonic
synths had just only one
gate, therefore in single
MIDI channel mode it
duplicates Gate1, but in
two MIDI channel mode,
it works independently
This is clock rate LED
Setting MIDI channel
Connect MIDI keyboard to the module!
Push PROGRAMM button for “4”. MIDI LED
will start to blink slowly. Select midi channel
by pushing a key on the keyboard. C of any
octave corresponds to MIDI channel 1, C# ‑
channel 2, D – channel 3, etc. Channels 1‑12
can be assigned to send midi messages to
the module.
For two MIDI channel configuration push
and hold two keys simultaneously.
CV1/Gate1 will be assigned to the lowest
midi channel, CV2/Gate2 – to highest.
Push the PROGRAMM button to advance
to MOD output configuration.
MOD output
configuration
In MOD output configuration mode MIDI
LED starts to blink faster.
If you wish to assign a modulation wheel
to MOD output, simply rotate it on the midi
controller.
If you wish to assign key velocity to
the MOD output, push any key on the
keyboard.
Push PROGRAMM button to confirm, and
the module will exit configuration mode.
1V/OCT calibration (optional)
Black MIDI‑CV modules come precisely
calibrated, but you may wish to adjust
calibration to your modular system
specifics. To do so, connect midi keyboard
to the module, set VOICE switch to 1
Voice mode and connect CV1 output
to a calibrated VCO 1V/oct input and a
chromatic tuner to the output of the VCO.
Disconnect MIDI‑CV module from the PSU.
Then push and hold PROGRAMM button
and connect the module to PSU busboard!
MIDI LED will start to blink, which means
the module is in calibration mode.
Play C3 on the keyboard, and tune the VCO
so that tuner reads C3!
Play C4 on the keyboard and check the
reading on the tuner. If it reads something
higher than C4, play B3 on the keyboard
repeatedly until the tuner reads C4. If it
reads something lower than C4, play C#4
repeatedly until the tuner reads C4.
Play C5 on the keyboard and check the
tuner. If it reads something higher than C5,
play repeatedly B4 until the tuner reads C5,
etc. Continue until you have perfect tuning
along all octaves.
Push the PROGRAMM button to start
calibration of the second CV output.
The procedure is exactly same.
Once calibration is completed, push
PROGRAMM Button to exit calibration
mode.
BLACK MIDI-CV
SAFETY INSTRUCTIONS
DISPOSAL
Please follow the instructions for use of this
Erica Synths module below, ‘cause only this
will guarantee proper operation of the module
and ensure warranty from Erica Synths.
Water is lethal for most of the electric devices,
unless they are made waterproof. Erica
Synths module is NOT intended for use in
a humid or wet environment. No liquids or
other conducting substances must get into
the module. Should this happen, the module
should be disconnected from mains power
immediately, dried, examined and cleaned by
a qualified technician.
Do not expose the module to temperatures
above +50° C or below ‑20° C.
Transport the instrument with modules
installed carefully, never let it drop or fall over.
Warranty does not apply to modules with
visual damages.
The module has to be shipped in the original
packaging only. Any module shipped to us
for return, exchange and/or warranty repair
has to be in its original packaging. All other
deliveries will be rejected and returned to you.
Make sure you keep the original packaging
and technical documentation.
You will find Erica Synths terms of warranty at
http://ericasynths.lv/en/terms/
Items for return, exchange and/or warranty
repair have to be sent to: Erica Synths,
Andrejostas Str.12, Riga, Latvia, LV‑1045
This device complies to the EU guidelines and is
manufactured RoHS conforming without use of
led, mercury, cadmium and chrome.
Nevertheless, this device is special waste and
disposal in household waste is not
recommended.
Designed and made in Latvia.
User manual by Girts Ozolins@Erica Synths.
Design by Baiba Stelle.
Copying, distribution or any commercial use in
any way is prohibited and needs the written
permission by Erica Synths.
Specifications are subject to change without
notice.
In case of any questions feel free to contact us
via e‑mail info@ericasynths.lv
Check out other Erica Synths modules & devices
at www.ericasynths.lv
BLACK MIDI-CV

Specyfikacje produktu

Marka: Erica Synths
Kategoria: nieskategoryzowany
Model: Black MIDI-CV

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Erica Synths Black MIDI-CV, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje nieskategoryzowany Erica Synths

Erica Synths

Erica Synths Black DADSR EG Instrukcja

20 Czerwca 2024
Erica Synths

Erica Synths Black VC Clock v2 Instrukcja

20 Czerwca 2024
Erica Synths

Erica Synths Sonic Potions LXR 7 Instrukcja

20 Czerwca 2024
Erica Synths

Erica Synths Trigger Out Instrukcja

20 Czerwca 2024
Erica Synths

Erica Synths Hi-Hats A Instrukcja

20 Czerwca 2024
Erica Synths

Erica Synths Black CV Expander Instrukcja

20 Czerwca 2024
Erica Synths

Erica Synths Black Hole DSP II Instrukcja

20 Czerwca 2024
Erica Synths

Erica Synths Fusion Instrukcja

20 Czerwca 2024
Erica Synths

Erica Synths Black MIDI-CV Instrukcja

20 Czerwca 2024
Erica Synths

Erica Synths Black Stereo Mixer Instrukcja

20 Czerwca 2024

Instrukcje nieskategoryzowany

Najnowsze instrukcje dla nieskategoryzowany

Meec Tools

Meec Tools 010-084 Instrukcja

6 Października 2024
Outwell

Outwell Scenic Road 250 Instrukcja

5 Października 2024
Impact

Impact Qualite QL-3560-LED Instrukcja

4 Października 2024
Impact

Impact QuikBalance Instrukcja

4 Października 2024
Impact

Impact CA-112 Instrukcja

4 Października 2024
Impact

Impact Forever Ready Cool FRC-24-LED Instrukcja

4 Października 2024
Impact

Impact LS-BHA Instrukcja

4 Października 2024
Impact

Impact LKB-5C Instrukcja

4 Października 2024
Impact

Impact Varipole Drop Ceiling Adapter Instrukcja

4 Października 2024
Impact

Impact RST-001 Instrukcja

4 Października 2024