Instrukcja obsługi Erica Synths Black Hole DSP III

Erica Synths nieskategoryzowany Black Hole DSP III

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Erica Synths Black Hole DSP III (3 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/3
OUT ROUT LDRY/WET CVIN RIN L
PATCH CVPARAM3 CVPARAM2 CVPARAM1 CV
BLACK HOLE DSP2
PARAM 1 PARAM 2 PARAM 3
IN LEVEL CRUSH CV LVL
CRUSH CV
PATC HCRUSH
BLACK HOLE DSP II
THANK YOU FOR CHOOSING ERICA
SYNTHS BLACK SERIES MODULE!
Erica Black Series include high-end,
unique functionality and superior quality
modules. Only the best, highest quality
components are used, all inputs and
outputs are protected against undesired
overvoltage. When designing Black
Series, we put design and usability
superior. Big knobs are assigned to key
functions of the module, which makes
Black Series ideal for live performances.
Enjoy!
If the doors of perception were cleansed
everything would appear to man as it is,
infinite.
/
William Blake
/
Erica Synths Black Hole DSP II , an
updated version of Black Hole DSP features
24 custom eects, designed in close
co-operation of Erica Synths team rider
KODEK and creator of Spin CAD software
Gary Worsham. Each eect has 3 manually
and CV controllable parameters, manual
and CV control over sampling frequency
for spanning from 48kHz to really Lo-Fi
crunchy sound and full analogue dry/
wet control. All eect parameter settings
can be saved to the memory and instantly
recalled with the eect, which makes Black
Hole DSP II ideal for live performances.
FEATURES:
24 custom eects based on Spin FV-1 chip
Stereo INs and OUTs
3 manually and CV controllable parameters
CV controlled eect select
Manually and CV controllable clock rate
reduction for noisy bitcrush
Eect settings memory
Full analogue Dry/Wet control
Audio clipping LED
The display shows currently selected eect.
The eect is activated by pushing the
PATCH encoder promptly, and a dot in the
bottom left corner will appear –
this indicates that the eect is on.
When a Parameter knob returns to the
saved position, a dot will blink once.
The encoder
has several features.
Rotate the encoder to select
one of 24 eects.
Push the encoder promptly
to confirm the selection and
activate the eect.
Push and hold the encoder
to save (a display will indicate
SA) all parameter settings
with the eect!
To recall parameter settings,
push the encoder twice (the
display will indicate RC)
This is Crush CV attenuator
This is manual Dry/Wet
control. If you want to use
the Black Hole DSP II as
send eect unit make sure
you set this knob all way CW
(full wet)
These are CV inputs for
each parameter control.
Patches will change on very
slow CV rates only, as the
module requires some time to
read patch from the memory
TECHNICAL SPECIFICATIONS:
Input signal amplitude ...........-5…+5V (or 0…+10V)
Output signal amplitude........................-10V - +10V
Max sampling rate.........................................48kHz
CV level (full span).....................................-5V - +5V
Power consumption…....................+170mA, -56mA
Module width…………………….............................16HP
Module depth……….........................................35mm
These are audio signal
inputs. The Left input is
normaled to the Right, so
you can input mono signal
and get impressive
stereo eect
This is Dry/Wet CV input.
The module has full
analogue dry/wet
circuit
Use these potentiometers
to adjust the eect
parameters!
Refer to the table below for
parameter description!
All parameter settings can
be saved with the eect
(PATCH) and recalled
instantly. If you wish to alter
saved parameter settings,
rotate the potentiometer
until the segments in the
patch number screen flash
once – this means, you
have reached initial setting
of the parameter and you
start to altering it.
This is the input level
attenuator – make sure that
clipping LED is not lit
Clipping LED. Adjust the
input signal level so that
LED lights up accidentally
This is sample rate
knob. Turn it clockwise
to reduce clock rate and
get vintage tape echo
like eects and extreme
bitcrush
Signal outputs. All eects
are designed for stereo
outputs, but they sound
great also mono
BLACK HOLE DSP II
PARAMETER 1
FEEDBACK
FEEDBACK
FEEDBACK
FEEDBACK
FEEDBACK
FEEDBACK
FEEDBACK
FEEDBACK
FEEDBACK DELAY TIME PITCH SHIFTER
PRE DELAY REVERB SIZE SHIMMER PITCH (-/+12 semi)
PRE DELAY REVERB SIZE SHIMMER AMOUNT (+12 semi)
PRE DELAY REVERB SIZE SHIMMER AMOUNT (-12 semi)
PRE DELAY SIZE TONE
PRE DELAY SIZE TONE
FEEDBACK SIZE TONE
SATURATION TONEREVERB SIZE
RATE WIDTH
FEEDBACK TIME LEFT TIME RIGHT
OVERDRIVE BITCRUSH RIP
FEEDBACK PHASE LEFT PHASE RIGHT
SHIFT 1 (-12/+12) SHIFT 2 (-12/+12) CROSSFADE (1/MIX/2)
AFTER 12 - RECORD 10ms - 500ms LOW PASS FILTER
AFTER 12 - RECORD 10ms - 500ms HI PASS FILTER
FREQ 1 FREQ 2 FREQ 3
PARAMETER 2 PARAMETER 3FXNr.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
TIME LEFT TIME RIGHTDUAL DELAY
DELAY TIME HI PASS FILTERHIPASS DELAY
DELAY TIME PHAZER AMOUNT // ADDS 3RD TAPPHAZED DELAY
DELAY TIME CHIRP AMOUNTCHIRP DELAY
DELAY TIME FEEDBACK TAP TIMETAP TAP DELAY
GRAIN SIZE WIDTH
GRANULAR DELAY
PITCH SHIFT DELAY
SHIMMER DRIFT
SHIMMER +
SHIMMER -
BIG / HALL REVERB
ROOM REVERB
STALKER REVERB
SATURATED REVERB
HAVOC CHORUS
SERVO FLANGER
RIPPER
SPACE PHASER
DUAL PITCH SHIFTER
LP FREEZER
HP FREEZER
DRONE BANK
* For effects 19, 22, 23, 24 dry/wet control should be full wet.
** Controls in bold may increase output level radically - use them carefully!
DELAY TIME LOW PASS FILTERLOWPASS DELAY
DELAY TIME RAISER // ON AFTER 12 O CLOCK
HELLRAISER DELAY
FEEDBACK
BLACK HOLE DSP II
SAFETY INSTRUCTIONS
Please follow the instructions for use of this
Erica Synths module below, ‘cause only this
will guarantee proper operation of the module
and ensure warranty from Erica Synths.
Water is lethal for most of the electric devices,
unless they are made waterproof. Erica
Synths module is NOT intended for use in
a humid or wet environment. No liquids or
other conducting substances must get into
the module. Should this happen, the module
should be disconnected from mains power
immediately, dried, examined and cleaned by
a qualified technician.
Do not expose the module to temperatures
above +50° C or below -20° C.
Transport the instrument with modules
installed carefully, never let it drop or fall over.
Warranty does not apply to modules with
visual damages.
The module has to be shipped in the original
packaging only. Any module shipped to us
for return, exchange and/or warranty repair
has to be in its original packaging. All other
deliveries will be rejected and returned to you.
Make sure you keep the original packaging
and technical documentation.
DISPOSAL
You will find Erica Synths terms of warranty at
http://ericasynths.lv/en/terms/
Items for return, exchange and/or warranty
repair have to be sent to: Erica Synths,
Andrejostas Str. 43, Riga, Latvia, LV-1045
This device complies to the EU guidelines and is
manufactured RoHS conforming without use of
lead, mercury, cadmium and chrome.
Nevertheless, this device is special waste and
disposal in household waste is not
recommended.
Designed and made in Latvia.
User manual by Girts Ozolins@Erica Synths.
Design by Edmunds Pavlovskis.
Copying, distribution or any commercial use in
any way is prohibited and needs the written
permission by Erica Synths.
Specifications are subject to change without
notice.
In case of any questions feel free to contact us
via e-mail info@ericasynths.lv
Check out other Erica Synths modules & devices
at www.ericasynths.lv

Specyfikacje produktu

Marka: Erica Synths
Kategoria: nieskategoryzowany
Model: Black Hole DSP III

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Erica Synths Black Hole DSP III, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje nieskategoryzowany Erica Synths

Erica Synths

Erica Synths Black DADSR EG Instrukcja

20 Czerwca 2024
Erica Synths

Erica Synths Black VC Clock v2 Instrukcja

20 Czerwca 2024
Erica Synths

Erica Synths Black Code Source Instrukcja

20 Czerwca 2024
Erica Synths

Erica Synths Sonic Potions LXR 7 Instrukcja

20 Czerwca 2024
Erica Synths

Erica Synths Trigger Out Instrukcja

20 Czerwca 2024
Erica Synths

Erica Synths Hi-Hats A Instrukcja

20 Czerwca 2024
Erica Synths

Erica Synths Black CV Expander Instrukcja

20 Czerwca 2024
Erica Synths

Erica Synths Black Hole DSP II Instrukcja

20 Czerwca 2024
Erica Synths

Erica Synths Fusion Instrukcja

20 Czerwca 2024
Erica Synths

Erica Synths Pico EF Instrukcja

20 Czerwca 2024

Instrukcje nieskategoryzowany

Najnowsze instrukcje dla nieskategoryzowany

Asko

Asko DBI644MIB.S.TW/1 Instrukcja

28 Października 2024
Asko

Asko DFS233IB.S.TW/1 Instrukcja

28 Października 2024
Emko

Emko EZM-9920 Instrukcja

27 Października 2024
Emko

Emko ESM-3712-H Instrukcja

27 Października 2024
Emko

Emko ATS-10 Instrukcja

27 Października 2024
Emko

Emko EAOM-11.2 Instrukcja

27 Października 2024
Emko

Emko EPM-3790 Instrukcja

27 Października 2024
Emko

Emko EPM-7790 Instrukcja

27 Października 2024
Livarno Lux

Livarno Lux IAN 108340 Instrukcja

27 Października 2024
Livarno Lux

Livarno Lux HG06009A-BS Instrukcja

27 Października 2024