Instrukcja obsługi ENTES DTR-10

ENTES Niesklasyfikowane DTR-10

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla ENTES DTR-10 (36 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 13 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/36
www.entes.eu
DTR-10 User Manual and
Menu Map
Adr: Dudullu OSB; 1. Cadde; No:23 34776 Ümraniye - İSTANBUL / TÜRKİYE
Tel: Fax: E-mail: Web: +90 216 313 01 10 +90 216 314 16 15 contact@entes.eu www.entes.eu
Call Center Technical Support: 0850 888 84 25 A5299 / Rev.4
1 2
DTR-10, which has a real time clock, is an electronic timer that calculates the sunset and sunrise periods automat-
ically. It is designed for controlling the devices which are connected to its contacts according to sunset, sunrise
and the time periods which are programmed by the user.
ESC Button : It is used to switch between monitoring menus. In the programming mode, it is used to cancel
a parameter change or to return to the previous menu.
SET Button : It is used to switch between monitoring menus. When it is pressed for 3 seconds, programming
YUKARI mode is entered. In the programming mode, it is used to apply a parameter change or to enter
to a menu.
DOWN Buttons :
In the monitoring menu, it is used to switch between programs to show their activity in a day.
When the DOWN button is pressed for 3 seconds, C1 relay goes into manual mode and when
the UP button is pressed for 3 seconds, C2 relay goes into manual mode. In the programming
menu; it is used to browse between menus, to select parameters and to adjust values with digits.
Precautions for Installation and Safe Use
If below precautions are not properly observed and carried out, it may result in cases with injury or death. -
Disconnect power before working on the device.
- When device is connected to the network, do not remove the front panel.
- Do not clean the device with solvent or similar items. Only clean with dry cloth.
- Verify correct terminal connections before energizing the device.
- Install the device on the electrical panel.
- Contact your authorized reseller in case problems occur with your device.
No responsibility is assured by the manufacturer or any of its subsidiaries for any consequences rising
out of the use of this material.
- The output loads connected to the relays do not function if auxiliary supply is absent. Even if the relay status
is monitored as “on”( and/or ), auxiliary supply is a must for the operation.
- There are two reserves in the device. Programmed data is protected by these reserves against power outages.
- For long time reserve, a battery is used. If the device is not continously supplied with voltage and waited on the shelf,
the battery life is 5 years.
- Reserve battery should only be changed by the authorized service.
MANUAL MODE :
In order to use the relay outputs manually, DTR-10 has to be in the monitoring mode. The DOWN button is used to
switch the C1 relay to manual mode and the UP button is used to switch the C2 relay to manual mode. When the UP
or DOWN button is pressed for 3 seconds, “MANUAL” indication appears on the screen. If this is done while the relay
C1 or C2 is activated, that relay will be deactivated. If it is done while the relay C1 or C2 is deactivated, no switching
will occur. When the device is in manual mode and the relay is not energized, and the DOWN button is pressed once
C1 contact will turn o its contact or when the UP button is pressed once C2 contact will turn o its contact at the
end of a 3-second delay. During this delay, the symbol indicating the state of the relay contact is ashing. After the
activation of the contact, when the DOWN button is pressed again for 3 sec, C1 relay will exit the manual mode. When
the UP button is pressed again for 3 sec, C2 relay will exit the manual mode. The relay will stay activated or deactivated
according to the program ow. When both of the the relays are in manual mode, “AUTO” indication will dissappear
from the screen.

Specyfikacje produktu

Marka: ENTES
Kategoria: Niesklasyfikowane
Model: DTR-10

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z ENTES DTR-10, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane ENTES

ENTES

ENTES GKRC-22E Instrukcja

3 Stycznia 2025
ENTES

ENTES GKRC-21E Instrukcja

3 Stycznia 2025
ENTES

ENTES SER-YU Instrukcja

27 Grudnia 2024
ENTES

ENTES ERB-50 Instrukcja

8 Października 2024
ENTES

ENTES GEM-10SH Instrukcja

8 Października 2024
ENTES

ENTES RGSR-24S-OG Instrukcja

8 Października 2024
ENTES

ENTES RGSR-20S-OG Instrukcja

8 Października 2024
ENTES

ENTES RG3-15CL Instrukcja

8 Października 2024
ENTES

ENTES MPR-53S-96 Instrukcja

8 Października 2024
ENTES

ENTES MPR-47S-L Instrukcja

8 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

GBC

GBC ThermaBind T500Pro Instrukcja

15 Stycznia 2025
Da-Lite

Da-Lite Parallax 29850 Instrukcja

15 Stycznia 2025
Crivit

Crivit IAN 290909 Instrukcja

15 Stycznia 2025
Tripp Lite

Tripp Lite SmartRack SRW12US Instrukcja

15 Stycznia 2025
Powerfix

Powerfix IAN 280221 Instrukcja

15 Stycznia 2025
AGM

AGM Rattler TC35-640 Instrukcja

15 Stycznia 2025
AGM

AGM Wolf-7 Pro Instrukcja

15 Stycznia 2025
AGM

AGM Anaconda TC50-640 Instrukcja

15 Stycznia 2025
AGM

AGM Secutor Pro TS50-640 Instrukcja

15 Stycznia 2025
Microchip

Microchip AT91SAM9M11 Instrukcja

15 Stycznia 2025