Instrukcja obsługi Emos P4518

Emos Flesz P4518

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Emos P4518 (20 stron) w kategorii Flesz. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/20
1450000180_31-P4518_00_01 148 × 210 mm
www.emos.eu/download
P4518|E709A-COB3W+6
GB LED Work Light
CZ LED pracovní svítilna
SK LED pracovné svietidlo
PL Lampa warsztatowa LED
HU LED-es munkalámpa
SI Delovna LED svetilka
RS|HR|BA|ME LED radna svjetiljka
DE LED-Arbeitsleuchte
UA Світлодіодний робочий ліхтарик
RO|MD Lampă LED de lucru
LT Darbinis šviesos diodų žibintas
LV LED lukturis darbam
EE LED-töötuli
BG LED pаботна лампа
2
1.
2.
4.
5. 6.
3.
6× LED 20 lm 24 h 27 m
COB LED 200 lm 7 h 19 m
380 lm 3,5 h 26 m
GB | LED Work Light
Specications
The rechargeable lamp is resistant to rough conditions (dust, dirt) and is therefore suitable for technicians, handymen and
cottagers, as well as for use in the car. The lamp has a magnet and a hook for hanging. The reector of the lamp can be rotated
– the top part horizontally by 360° and vertically by 180° to either side, the bottom part (handle) with a magnet horizontally by
360°. The lamp can be charged, or recharged, from a 100–240 V AC, 50/60 Hz network or from a 12/24 V DC car socket.
Description
1. Hook
2. Switch
3. Rotating handle with a magnet
4. Recharging LED indicator, connector for power supply
5. COB source
6. 6 LED source
Specications:
Light source: COB LED + 6× LED
Accumulator pack: Li-Ion 18650–3.7 V DC/2 500 mAh
Electric grid charging power source: type SD-G0501000D
input 100–240 V AC, 50/60 Hz,
output 5 V DC/1 000 mA
Recharging from car: 12/24 V DC
Power source for car adapter: input: 12/24 V DC; output: 5 V DC/1 000 mA
Recharging the Accumulator
Before the rst use or if the lamp does not light up or ashes (which indicates a weak battery) the accumulator has to be
recharged. Charging the accumulator pack when it is completely at takes about 3 hours (depending on the degree to which
the accumulator has been discharged). Recharge the lamp in dry indoor areas.
1. Connect the network power adapter (type SD-G0501000D) to a 100–240 V AC, 50/60 Hz network.
2. Turn the switch on the lamp to the o position.
3. Connect the network power adapter into the lamp’s power connector – a red light will turn on on the lamp. When the lamp
(accumulator) is fully recharged, the LED will turn green.
4. After recharging, disconnect the adapter from the lamp.
The accumulator can be recharged intermittently – it has no memory eect.
The lamp can also be recharged in a car – through the 12/24 V DC lighter socket. Procedure for plugging in and recharging is
similar as when using a network adapter. After recharging, disconnect the car adapter. The lamp can be recharged using a car
adapter only when the vehicle is stationary and the engine is turned o. Do not under any circumstances charge the lamp when
the car engine is running or the car is in motion.
The LED light sources have a 50 000 hour service life and therefore need not be recharged. After exhausting, the entire lamp
can disposed of.
3
Changing the Accumulator:
The accumulator should only be changed by a skilled user, ideally with qualications in electrical engineering.
1. When changing the accumulator, turn the lamp switch to the o position.
2. Carefully remove the screws from the rear cover of the lamp and take the lamp apart.
3. Remove the accumulator pack and replace with a new one with same dimensions and electrical parameters. The new
accumulator must be purchased only from the manufacturer. Never use non-original components. Make sure to observe
the correct polarity when changing the accumulator.
4. Reassemble the lamp by reversing the procedure for disassembly.
WARNING
• When new, the lamp must rst be charged before use.
• The lamp’s accumulator must be kept charged to prevent the voltage from dropping below the threshold level. Therefore,
it is recommended to recharge the lamp at least once every 3 months even when it is not being used.
• If the lamp does not shine or the light is weak or ashes, immediately recharge the accumulator.
• If the accumulator is damaged or destroyed due to non-observance of the above rules, complaints led within the warranty
period regarding the lamp (accumulator) will not be recognized.
• Use the network adapter type SD-G0501000D only for recharging the lamp; do not recharge any batteries designed for
other purposes.
• The network adapter and car adapter must be used in dry indoor areas.
• When replacing the accumulator, make sure to observe the correct polarity.
• Do not throw the accumulator into a re and do not disassemble or short-circuit it.
• After depletion, the accumulator becomes hazardous waste. After depletion, do not dispose of the accumulator in municipal
waste. Turn the accumulator in at take-back sites such as the shop where the lamp was purchased.
• Upon completion of the lamp’s life cycle, dispose of the lamp in an environmentally-friendly way.
• If water enters the interior of the lamp, remove the accumulator and dry the interior of the lamp thoroughly. Do not under
any circumstances use the lamp.
• The lamp is not intended for use by persons whose physical, sensory or mental disability or lack of experience and expertise
prevents its safe use, unless they are supervised or instructed in the use of the appliance by a person responsible for their
safety. Children should not be allowed to play with the lamp.
Do not dispose with domestic waste. Use special collection points for sorted waste. Contact local authorities for informa-
tion about collection points. If the electronic devices would be disposed on landll, dangerous substanoes may reach
groundwater and subsequently food chain, where it could aect human health.
Delivery List:
Lamp
Electric grid charging power source, type SD-G0501000D
Car adapter 12/24 V DC
Recharge cable
Manual
CZ | LED pracovní svítilna
Specikace
Nabíjecí svítilna je odolná proti nešetrnému zacházení (prach, špína), proto je vhodná pro techniky, kutily, chataře a také do
auta. Svítilna má magnet a hák na zavěšení. Reektor svítilny je možné natáčet - horní část horizontálně o 360° a současně také
do stran vertikálně o 180°, dolní část (rukojeť) smagnetem horizontálně lze otáčet o 360°. Svítilnu lze nabíjet, případně dobíjet
ze sítě 100–240 V AC, 50/60Hz, nebo z automobilové zásuvky 12/24 V DC.
Popis
1. Hák
2. Vypínač
3. Otočná rukojeť s magnetem
4. LED indikace nabíjení, konektor pro připojení napájecího zdroje.
5. COB zdroj
6. 6 LED zdroj
Technická specikace:
Zdroj světla: COB LED + 6× LED
Akumulátorový pack: Li-Ion 18650–3,7 V DC/2 500 mAh
Síťový napájecí zdroj: typ SD-G0501000D;
vstup 100–240 V AC, 50/60 Hz
výstup 5 V DC/1 000 mA
Nabíjení z automobilu: 12/24 V DC
Napájecí zdroj do automobilu: adaptér do auta, vstup: 12/24 V DC; výstup: 5 V DC/1 000 mA

Specyfikacje produktu

Marka: Emos
Kategoria: Flesz
Model: P4518

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Emos P4518, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Flesz Emos

Emos

Emos P4544 Instrukcja

8 Października 2024
Emos

Emos P4541 Instrukcja

3 Października 2024
Emos

Emos P4525 Instrukcja

17 Września 2024
Emos

Emos P4532 Instrukcja

11 Września 2024
Emos

Emos P4518 Instrukcja

10 Września 2024

Instrukcje Flesz

Najnowsze instrukcje dla Flesz

Ledlenser

Ledlenser P9R Core LEP Instrukcja

15 Października 2024
LED Lenser

LED Lenser P5R Instrukcja

11 Października 2024
Brennenstuhl

Brennenstuhl TL 1201 AF Instrukcja

9 Października 2024
Brennenstuhl

Brennenstuhl TL 601 AF Instrukcja

9 Października 2024
Klein Tools

Klein Tools KHH56308 Instrukcja

9 Października 2024
Brennenstuhl

Brennenstuhl HL 400 AC Instrukcja

9 Października 2024
Nitecore

Nitecore MH40 Pro Instrukcja

8 Października 2024
Nitecore

Nitecore HU2000 Instrukcja

8 Października 2024
AccuLux

AccuLux UniLux PRO Instrukcja

8 Października 2024
AccuLux

AccuLux SL6 LED Instrukcja

8 Października 2024