Instrukcja obsługi Emos E8466

Emos Stacja pogodowa E8466

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Emos E8466 (56 stron) w kategorii Stacja pogodowa. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/56
E8466
GB Projection wireless weather station
CZ Projekční bezdrátová meteostanice
SK Projekčná bezdrôtová meteostanica
PL Projekcyjna bezprzewodowa stacja
meteorologiczna
HU Vezeték nélküli meteorológiai állomás
kivetítővel
SI
Projekcijska brezžična vremenska
postaja
RS HR| |BA Bežična meteorološka stanica
sprojektorom
DE Projektions-Funkwetterstation
UA Проекційна бездротова метеостанція
RO Stație meteo fără r cu proiecție
LT Projektuojanti belaidė meteorologinė
stotelė
LV Bezvadu meteoroloģiskā stacija
arprojektoru
2606150000_31-E8466 148 × 210 mm
www.emos.eu
2
GB Projection wireless weather station
Specications
radio controlled clock
indoor temperature: -5 °C to +50 °C
outdoor temperature: -20 °C to +60 °C
temperature resolution: 0.1 °C
accuracy of indoor temperature measurement: ±1.5 °C (-5 to 0 °C), ±1 °C (1 to 30 °C), ±1.5 °C (31 to 50 °C)
accuracy of outdoor temperature measurement: ±2 °C (-20 to 0 °C), ±1 °C (1 to 30 °C), ±2 °C (31 to 60 °C)
wireless sensor: transmission frequency 433 MHz
radio signal range: up to 30 m in an open area
number of sensors per connection: max. 3
power supply:
main unit: 1× 3 V CR2032 battery (included), 4.5 V DC/300 mA DC adapter (included)
sensor: 2× 1.5 V AA batteries (not supplied)
dimensions and weight without batteries:
main unit: 163 × 80 × 56 mm, 248 g
sensor: 65 × 100 × 35 mm, 75 g
Description of weather station and sensor
1 – SNOOZE button
2 – reverse projection display button
3 – time and temperature projector
4 – LCD display
A – date, day of week
B – current time
C – indoor temperature (IN), outdoor temperature (OUT)
D – weather forecast icon
5 – TIME button
6 – ALARM button
7 – CHANNEL/UP button
8 – 12/24 / DOWN button
9 – LOOP button
10 – RAINBOW button
11 – TUNE button
12 – FOCUS button
13 – MAX/MIN button
14 – RCC button
15 – °C/°F button
16 – RESET button
17 – display backlight OFF/LO/HI button
18 – connector to connect 4.5 V DC adapter
19 – weather station battery compartment (1× 3 V CR2032)
3
Sensor description
1 – sensor LED
2 – hole to hang the device on the wall
3 – RESET button
4 – sensor channel number switch
5 – battery compartment
Getting started
1. Insert the battery in the weather station (1× 3 V CR2032), connect the included 4.5 V DC adapter. The CR2032 battery is
only intended as a backup power source for storing the readings when the DC adapter is disconnected.
It is therefore necessary to use the DC adapter at all times!
2. Use the switch on the sensor to set the required sensor number and insert the batteries (2× 1.5 V AA). When inserting the
batteries make sure the polarity is correct to avoid damaging the weather station or sensor. Only use alkaline batteries of
the same type, do not use rechargeable batteries.
3. Place the two units next to each other. The weather station detects the remote sensor signal within 3 minutes. If the remote
sensor signal is not detected, press and hold the DOWN button to repeat the search.
4. If the outdoor temperature reading disappears from the display, press and hold the DOWN button on the weather station.
The weather station repeats the search for the sensor signal.
5. We recommend placing the sensor on the north side of the house. The range of the sensor may decrease substantially in
areas with large number of obstacles.
6. The sensor is resistant to dripping water, however, it should not be exposed to rain permanently.
7. Do not place the sensor on metal objects as this will reduce the transmission range.
8. If low battery icon is displayed, replace batteries in the sensor or weather station.
Switching over to another channel and connecting additional sensors
1. Repeatedly press the CHANNEL button at the back of the weather station to choose required channel of the sensor – 1, 2,
or 3. Then press and hold the DOWN button; the sensor number starts ashing.
2. Remove the cover from the battery compartment and insert batteries (2× 1.5 V AA).
3. Use the channel switch to set the required channel number – 1, 2, 3 and then insert batteries in the sensor. Replace the
battery cover. Data from the sensor will be loaded within 3 minutes.
4. If the sensor signal is not detected, remove the batteries and reinsert them.
Radio controlled clock (DCF77)
After registering with the wireless sensor, the weather station will automatically start searching for the DCF77 signal for 7minutes;
the following icon will ash depending on the DCF signal intensity.
no signal weak signal medium signal good signal
DCF signal reception icon
During the search, no other data on the display will be updated and the buttons will be disabled.
Signal detected – the icon stops ashing and displays the current time with the DCF icon.
Signal not detected – DCF icon is not displayed.
Press the RCC button shortly to repeat search for the DCF77 signal for 5 minutes, press and hold the RCC button to stop search
for the DCF77 signal. The DCF77 signal will be synchronised daily at the following times: 2:00, 8:00, 14:00, 20:00. In standard
conditions (at safe distance from sources of interference, such as TV sets, computer monitors), the reception of time signal
takes several minutes.
If the weather station does not detect the signal, follow these steps:
1. Move the weather station to another location and try to detect the DCF signal again.
2. Check the distance of the clock from the sources of interference (computer monitors or television sets). It should be at
least 1.5 to 2 m during the reception of the signal.
3. When receiving DCF signal, do not put the weather station to the proximity of metal doors, window frames and other metal
structures or objects (washing machines, dryers, refrigerators etc.).
4. In reinforced concrete structures (cellars, high-rise buildings etc.), the DCF signal reception is weaker, depending on the
conditions. In extreme cases, place the weather station close to a window toward the transmitter.
The reception of the DCF77 radio signal is aected by the following factors:
• thick walls and insulation, basements and cellars
• inadequate local geographical conditions (these are dicult to assess in advance)

Specyfikacje produktu

Marka: Emos
Kategoria: Stacja pogodowa
Model: E8466

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Emos E8466, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Stacja pogodowa Emos

Emos

Emos E0531 Instrukcja

14 Grudnia 2024
Emos

Emos E8670 Instrukcja

10 Września 2024
Emos

Emos E5111 Instrukcja

10 Września 2024
Emos

Emos E6018 Instrukcja

1 Września 2024
Emos

Emos E5101 Instrukcja

31 Sierpnia 2024
Emos

Emos E0387 Instrukcja

31 Sierpnia 2024
Emos

Emos E3003 Instrukcja

30 Sierpnia 2024
Emos

Emos E8647 Instrukcja

28 Sierpnia 2024
Emos

Emos RST01278 Instrukcja

27 Sierpnia 2024
Emos

Emos E0389 Instrukcja

27 Sierpnia 2024

Instrukcje Stacja pogodowa

Najnowsze instrukcje dla Stacja pogodowa

Ascot

Ascot GT-WS-07s Instrukcja

15 Stycznia 2025
Ventus

Ventus K0382 Instrukcja

14 Stycznia 2025
TFA

TFA 20.1082.17 Instrukcja

12 Stycznia 2025
Oregon Scientific

Oregon Scientific BAR310HG Instrukcja

12 Stycznia 2025
Auriol

Auriol AHFL 433 B2 Instrukcja

12 Stycznia 2025
Oregon Scientific

Oregon Scientific BAR 898 Instrukcja

11 Stycznia 2025
Davis

Davis Weatherlink Touch Console Instrukcja

11 Stycznia 2025
Taylor

Taylor 5156 Instrukcja

8 Stycznia 2025
La Crosse Technology

La Crosse Technology M71633 Instrukcja

8 Stycznia 2025
La Crosse Technology

La Crosse Technology V41CA Instrukcja

8 Stycznia 2025