Instrukcja obsługi Elica Varna EVR636S2

Elica Okap wyciągowy Varna EVR636S2

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Elica Varna EVR636S2 (24 stron) w kategorii Okap wyciągowy. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/24
Use, Care, and Installation Guide
Guide d’utilisation, d’entretien et d’installation
Guía de instalación, uso y mantenimiento
READ AND SAVE THESE INSTRUCTIONS
LISEZ CES INSTRUCTIONS ET CONSERVEZ-LES
READ AND SAVE THESE INSTRUCTIONS
Printed in Mexico
5
List of Materials
Parts supplied
Removing the packaging
CAUTION!
Removing the packaging
CAUTION:Wearglovestoprotectagainstsharpedges.First
remove the carton carefully and take out the duct cover.
CAUTION:Removecarefullytheglasscanopyfromthebox
and put it on a smooth safe surfaces.
Grasp the hood structure from the body and lift straight off the
box.
Remove and properly discard every carton and plastic wrap-
ping content in the package.
Remove parts out of the box, duct covers and other contents.
WARNING!
Removetheprotectivelmcoveringtheproductbefore
putting into operation.
Hoodcanopyassemblywithblower,transition.
2Halogenlamps.
2Greaselters.
Duct cover.
Hardwarebagwith:
Template.
Ductcoversupportbracket(1piece)
Use, care and installation guide
Woodscrews(6pieces-3/16”x1”3/4)
Hoodattachmentanchors
2 - 8x40 anchors
4 - 10x50 anchors
Assemblyscrews
2 - 2.9x6.5 mounting screws
2 - 3.5x9.5 mounting screws
Parts not supplied
Optional Accessories
DuctlessRecirculatingKit
TobeusedonlyintheDuctless(Recirculating)version
 includes:2charcoalltersanddeector
ProfessionalStainlessSteelGreaselter
Tools/Materials required
Wire nuts
Tapetomounttemplate
6”roundedmetalductlengthtosuitinstallation
Measuring tape
Pliers
Gloves
Knife
Safety glasses
Electricdrillwith5/16”and3/8”Bits
Strain relief
Spirit level
Duct tape
Screwdrivers:
Phillips(Posidrive)#2
Torx#2
Wire cutter/stripper
Masking tape
Hammer
Saw, jig saw or reciprocating saw
Dimensions and Clearances
*Ductless(Recirculating)versionOnly
**DuctingversionOnly
30” (76.2cm)
36” (91.2 cm
1½”
(4 cm)
20” (50.8 cm)
241/8
(61 cm)
10”
(25.4 cm)
7¼” (18.4 cm
*28
7/8” (73.3 cm) min
*421/16
” (106.9 cm) max
**283
/8” (72 cm) min
**38” (96.6 cm) max
6”
81/8” (20.7 cm
7
Mounting the duct cover bracket
Option A - Fixed heigh duct cover
Fromthehorizontallinetracedintheprevioussection,
 traceahorizontalparallellineasshownbelow.
Centerthebracketinthetophorizontallineandalignit
with the centerline, as described in the followinG
drawing.
Mark screw holes locations in the wall.
IMPORTANT. Check to be sure that holes locations are
leveled, and correctly centered by the vertical centerline.
Drill5/16”pilotholesinthemarkedlocations.
Install wall fastener anchors.
Drive wood screws, by hand, into the fasteners to allow an-
chors to expand. Remove screws.
Secure the bracket to the wall with wood screws and/or
fasteners.
Option B - Telescopic duct cover
Theductbracketshouldbeinstalledagainstthebackwall
andushwiththeceiling.Thisbracketwillholdthe
ductcoverinplaceatthetop(thisaextraaccessoryavailable
notincludedwiththehood).
Secure the bracket to the wall:
Alignthemarkedcenterlineonthebracketwiththe
centerline on the wall.
Mark 2 screw hole locations in the wall.
Drill5/16”pilotholesinthemarkedlocations.
Install wall fastener anchors.
Drive wood screws, by hand, into the fastener to allow
anchors to expand. Remove the screws.
Secure the bracket to the wall with wood screws and/or
fasteners.
Ceiling ducting
If the duct will vent straight up to the ceiling:
Use level to draw a line straight up, from the centerline on
the template to the ceiling.
Measureatleast4-12/16”fromthebackwalltothecircle
centerofan6-½”holeontheceiling.
Wall ducting
If ductwork will vent to rear:
Use a level to draw a line straight up from the centerline
on the template.
Measureatleast23-12/16”(themeasuremightvary
dependigontheelbowused)abovethepencillinethat]
indicates the bottom installation height, to the circle center
ofan6-½”diameterducthole(Holemaybeelongatedfor
 ductelbow).
House wiring location
Thejunctionboxislocatedonthetopleftsideofthehood.
Wiringshouldenterthebackwallatleast20”abovethe
bottomoftheinstallationheight,andwithin5-7/8”and
 4-7/8”oftheleftsideofthecenterline.
Centerline
Bracket line
27 28/32
Horizontalstraightpencilmarkedline
Desired installation height
VerticalCenterline
Ceiling
Wall
For ceiling vent ducting4
12/16”circlecenter
to wall
Ceiling
6½”diameterhole
FORWALLVENTDUCT Circle center at
2312/ 16”abovethe
marked bottom
pencil line
Horizontalstraight
pencil line


Specyfikacje produktu

Marka: Elica
Kategoria: Okap wyciągowy
Model: Varna EVR636S2

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Elica Varna EVR636S2, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Okap wyciągowy Elica

Elica

Elica EST630SS Instrukcja

15 Stycznia 2025
Elica

Elica Haiku EHK624SS Instrukcja

8 Października 2024
Elica

Elica Haiku EHK613SS Instrukcja

8 Października 2024
Elica

Elica ERA C PRF0194197 Instrukcja

3 Października 2024
Elica

Elica ERA PRF0194191 Instrukcja

3 Października 2024
Elica

Elica HAIKU PRF0146254 Instrukcja

3 Października 2024
Elica

Elica Fold S PRF0189419 Instrukcja

3 Października 2024

Instrukcje Okap wyciągowy

Najnowsze instrukcje dla Okap wyciągowy