Instrukcja obsługi Elektrobock WS301

Elektrobock odbiornik WS301

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Elektrobock WS301 (4 stron) w kategorii odbiornik. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/4
U N D E R T HE S W I T C H
WS301
WS
WS
WS
WS3
3
3
30
0
0
01
1
1
1
MADE IN CZECH REPUBLIC
W I R E L E S S
R E C E I V E R
for wireless control of various electric devices
R A N G E
UP T O
15 0 M
- to control all transmitters series WS3xx can
be used
- small dimensions allow mounting directly into
the installation box
- for heaters, circulation pumps, lighting, air
conditioning and other equipment up to 16 A
INSTALLATION
Wiring diagram:
230 V/ 50 Hz
L
N
max.
16 A
L N
FUNCTION BUTTON ( R ) :
SHORT PRESSING (for about 1.5s)
- coding.
LONG PRESSING (for about 5s)
- RESET deleting the code from the
memor y (the LED1 and LED2
flash simultaneously).
WS301 is suitable for switching on electric equipment. Transmitters, se-
ries WS3xx, can be used as a remote control (WS310-stick, WS320-
door contact transmitter, the current channel list on www.elbock.cz).
To be installed in internal rooms. Do not locate near power lines! The device
can only be installed by a person with adequate qualification!
The installation must be executed in a voltage-free state!
1. Switch off the main circuit breaker and connect it to the receiver according
to the diagram;
2. Switch on the main circuit breaker; the LED1 lits up on the receiver; BASIC MODE;
3. Pressing the FUNCTION BUTTON for about 5 sec, will erase the memory
(LED1 and LED2 simultaneous long flash), RESET MODE;
4. Pressing the FUNCTION BUTTON for about 1.5 sec, will get the receiver
into a setting mode for SWITCH ON (LED2 flashing);
5. Press the appropriate button, based on a transmmitter, for transmitting of
a code for SWITCH ON, LED1 flashing and receiver waits for SWITCH OFF.
6. In next step press the same button (or another), on the transmitter, for
transmitting of code for SWITCH OFF;
WS301
7. For setting COUNTING MODE proceed in a similar way;
(!When setting other functions do not use RESET - otherwise, the previ-
ous settings will be erased, it is possible to set up to 16 control buttons!)
8. Pressing the FUNCTION BUTTON for about 1.5 sec, will get the receiver
into a setting mode for SWITCH ON (LED2 flashing);;
9. Press the appropriate button, based on a transmmitter, for transmitting of
a code for SWITCH ON, LED1 flashing and receiver waits for SWITCH OFF.
10. Wait for 20sec, then the receiver is on SETTING TIME MODE (LED1 flashing
and LED2 lit); (!Setting range of time is 1s to 8 hours!)
11. Start to count down of the time,for which the device should be switched on. After the
expiry of the time you have requested press the transmitter button to SWITCH OFF.
EXPLANATION: LIT UNLIT FLASHING
LED2 FUNCTIONS OF WS301 - indication on receiver
1, power on 230V/ 50Hz
2, device is off
receiver waits for SWITCH ON code, if the code is not re-
ceived during 20 sec., receiver goes back to BASIC MODE
receiver waits for SWITCH OFF code, if the code is not received
during 20 sec. receiver goes back to SETTING TIME MODE
device is on
From the beginning of the time count down, receiver waits for SWITCH
OFF code, receiver goes back to BASIC MODE after receiving the code.
device is on and counts down the time (after a set time
automatically turns off and goes into BASIC MODE.
BASIC MODE
SWITCH ON MODE
SWITCH OFF MODE
RELAY SWITCHED
TIME SETTING MODE
COUNT DOWN MODE
flashing simultaneously (5x) - code was erased, is
necessary to set receiver again RESET MODE
LED1
flashing alternaltely - indicates that the transmitter, which
controls the reciever, has exhausted batteries! LOW BATTERY
(in the transmitter)

Specyfikacje produktu

Marka: Elektrobock
Kategoria: odbiornik
Model: WS301

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Elektrobock WS301, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje odbiornik Elektrobock

Elektrobock

Elektrobock WS301 Instrukcja

30 Grudnia 2025
Elektrobock

Elektrobock BT001 Instrukcja

16 Września 2024
Elektrobock

Elektrobock BT003 Instrukcja

8 Września 2024
Elektrobock

Elektrobock BT002 Instrukcja

5 Września 2024
Elektrobock

Elektrobock Pocket Home PH-SP1 Instrukcja

5 Września 2024
Elektrobock

Elektrobock Pocket Home PH-SP2 Instrukcja

31 Sierpnia 2024
Elektrobock

Elektrobock Pocket Home PH-PK20 Instrukcja

26 Sierpnia 2024
Elektrobock

Elektrobock Pocket Home PH-BP1-P9 Instrukcja

20 Sierpnia 2024

Instrukcje odbiornik

Najnowsze instrukcje dla odbiornik

Marantz

Marantz SR-8000 Instrukcja

15 Stycznia 2025
AKAI

AKAI AM-32 Instrukcja

15 Stycznia 2025
Peavey

Peavey CKd 608 Instrukcja

15 Stycznia 2025
OSD Audio

OSD Audio Nero HTX4150 Instrukcja

14 Stycznia 2025
S.M.S.L

S.M.S.L PA200 Instrukcja

14 Stycznia 2025
Pyle

Pyle PFMRA340BB.5 Instrukcja

13 Stycznia 2025
Wavtech

Wavtech link700.4plus Instrukcja

13 Stycznia 2025
Behringer

Behringer NU6000DSP Instrukcja

12 Stycznia 2025
Denon

Denon DRA-935R Instrukcja

12 Stycznia 2025
Kenwood

Kenwood KMM-BT508DAB Instrukcja

12 Stycznia 2025