Instrukcja obsługi Electrolux EWE451PX-DWX5

Electrolux Kotły i bojlery EWE451PX-DWX5

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Electrolux EWE451PX-DWX5 (3 stron) w kategorii Kotły i bojlery. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/3

ELECTRIC WATER HEATER USER MANUAL

1. PARTS IDENTIFICATION

1. Front Cover

2. LED Indicators

i) Earth LED Indicator

ii) Power/ELCB LED Indicator

3. Test / Reset Button

4. Temperature Control Knob

Valve

Valve Lever

5. 3 in 1 Stop

i) Stop

ii) Flow Regulator Valve Adjustment

iii) Built-in-Filter

6. Mesh Filter

7. Handshower

Shower Bracket Holder

9. PVC Hose

10. Heater Base

14. Main PCB Board

15. Water Outlet Connection

16. Terminal Block

17. ELCB Board

18. TRIAC

19. Reed Switch Assy

20. Water Inlet Connection

11. Thermostat

12. Heater Tank

13. PCB Board (Test & Reset)

SAFETY INFORMATION

2.1 Products manufactured by Electrolux are safe

provided they are installed, used and maintained

in good working order in accordance with our

instructions and recommendations. Always refer

to this manual if you have any doubt.

2.2 The Electric Water Heater must be earthed.

Improper grounding could cause electrical shock.

2.3 If any of the following conditions occur as

shown below, immediately switch off the power

supply and contact the Electrolux Consumer

2.5 When the Electric Water Heater is

used by someone such as child, elderly

person, sick person and physically

handicapped person, the person

concerned is kindly requested to pay

attention and check the shower

temperature by hand from time to time.

2.6 During lightning/thunder, switch off the power

supply to the Electric Water Heater in ad vance to protect

the Electric Water Heater against possible damage.

2.7 The earth continuity conductor of the electrical

installation must be effectively connected to all

exposed metal parts of other appliances and

services in the room, which in the Electric Water

Heater is to be installed to conform to local

regulations and ensure proper earthing/grounding

for ELCB to be effective.

NOTE : When removing the Electric Water Heater

from package, a small amount of water may be

found inside. This is normal as the Electric Water

Heater is tested during manufacturing process.

WARNING !

If the Electric Water Heater begins to make an

odd noise, smell or smoke.

If ELCB trips and Electric Water Heater Indicator

does not light up.

Water temperature cannot be controlled.

If the Electric Water Heater shows signs of a

distinct change in performance.

If water leaks from inside.

2.9 Installation must be carried out by a

quali ed personnel and in compliance local ﬁ

2.10 This Electric Water Heater must be

permanently connected to the direct main line

supply. A plug and socket is not recommended

to be used.

2.11 For the correct size of wire conductor

corresponding to different electrical loadings,

2.12 This Electric Water Heater operates at a

minimum water ow rate of 2.0 litre/minﬂ

and maximum working

2.13 The Electric Water Heater will not function

if there is insuf cient water ow (min 2.0 litre/minﬁ ﬂ

2.14

The built-in ELCB will automatically cut off

the power supply in case there is a current

2.15

The thermostat will automatically cut off the

power supply if it has sensed an abnormal rise in

water temperature.

CAUTION !

authority regulations.

please refer to Table 1.

pressure of 6 bars.

For direct connection from the water tank, the

Electric Water Heater must have an installation

minimum 1.0m below the water tank.

leakage over 15mA.

Care Center. Never attempt to re pair the Electric

Water Heater yourself:

User is advised to test and adjust the

water temperature before using.

2.8 WARNING : Metallic / chromed hose and

conductive control valve shall not be used.

3. ELECTRIC WATER HEATER UNIT INSTALLATION

3.1 Select a suitable position in the bathroom.

3.2 Remove the screw (A) at the bottom of the

Electric Water Heater

. (Fig. 2)

3.3 Remove the Front Cover from the bottom and then lift up the front cover.

3.4 Mark 3 Screw points of the Heater Base on the wall. The

Electric Water Heater

position should be

1.5m above the bathroom floor. (Fig. 2)

3.6 Use 6mm diameter drill and make the wall plug holes in depth of 34mm, for mount the Electric

Water Heater.

3.7 Insert the wall plugs and mount the

Electric Water Heater

firmly in position with the screws provided.

ELECTRIC WATER HEATER

UNIT INSTALLATION DIAGRAM

Fig. 2

Screw

3 in 1

stop valve

inlet

178mm

Washer

connect to

water inlet

connection

139mm

OFF

PLUMBING PROCEDURE

CAUTION!

IMPORTANT

This Electric Water Heater is a single point

system and the “Water Outlet” can only be

fitted to the Hose and Handshower set

provided. NO CONTROL VALVE OF

FITTING CAN BE FITTED TO THE WATER

OUTLET.

WARNING!

5. ELECTRICAL INSTALLATION

WARNING!

PROCEDURE :

5.7 Connect the cable as following: (Fig. 5)

BROWN or RED --LINE (L)

BLUE or BLACK --NEUTRAL (N)

GREEN or GREEN/YELLOW --EARTH (

)

5.8 Clamp the cable to the correct position.

Technician need to confirm the wire before

installation.

CHECK IF THE WIRING CONNECTION IS

CORRECT and replace the cover.

5.9 When putting back the Front Cover,

please take note of the procedure sho wn below :

-Ensure the position is correct, turn the

Temperature Control Knob Insert to OFF

position as shown in Fig.A (At the Heater Base)

-Install the Front Cover,turn the Temperature

Control Knob to OFF position to align with the

VR shaft as shown in Fig.B (At the Front Cover)

5.10 Fix the Temperature Control Knob and

screw ‘A’ (Fig. 2).

5.1 This Electric Water Heater must be

earthed. Improper grounding could cause

electrical shock.

5.2 Remember to SWITCH OFF the power

supply before carrying out any electrical work.

5.3 Refer to TABLE 1 for the correct cable size.

5.4 Use double insulation cable of over 2.5mm²

for 2.4kW, 3.5kW 3.8kW, 4.5kW 4.8kW models

and 4mm² for 3.6kW and 6.0kW model.

5.5 Lead the power cable from MCB to a

“ON/OFF’’ double pole Linked Switch having a

contact separation of at least 3mm in all poles

outside the bathroom, then lead a cable to the

terminal block inside the Electric Water Heater.

(Fig. 4)

5.6 Insert the wall embedded cable through

Side Entry ‘A’ by cutting a hole at the source

cord rubber holder and lead the cable to

Cable Bracket ‘B’. (Fig. 6)

Always KEEP the water supply to the Electric Water

Heater free from mud and dirt at all time during usage.

4.1 Connect the 3 in 1 Stop Valve to the Water

Inlet with washer. Use correct tools to tighten

and be careful not to over tighten and damage

the plastic nut.

4.2 Connect the incoming water piping to the 3 in

1 Stop Valve (1/2” BSP).

Make sure to put the Mesh Filter between 3

in 1 Stop Valve and incoming water piping.

4.3

If in any case, the 3 in 1 Stop Valve is not use or

omitted, make sure to put the Mesh Filter

between the Electric Water Heater inlet pipe

and incoming water pipe.

4.4 Turn on the water mains to drain out all plumbing

dirts before connecting the water supply to the

Electric Water Heater, the water supply to the

Electric Water Heater must be free from mud and

dirt.

4.6 Hook the Handshower to the Slider Rail

Shower Holder and adjust to your ideal position.

4.7 Check if any water leakage.

4.8 Do not use sealing tape during piping

installation.

THE HEATER TANK MUST BE FILLED UP WITH

WATER BEFORE TURNING ON THE POWER

SUPPLY TO PREVENT ANY DRY BURNT DAMAGE

TO THE HEATING ELEMENT.

4.5 Connect the Hose and Handshower to the

outlet of Electric Water Heater, be sure to put in the

Washer in between the connection. (Fig. 2)

4.10 DO NOT APPLY PLUMBING CEMENT ON

CONNECTION. WHENEVER NECESSARY, USE

ONLY THREAD OR SEALING TAPE.

4.9 THE WATER INLET AND OUTLET MUST BE

INSTALLED CORRECTLY, OTHERWISE ELECTRIC

WATER HEATER WILL NOT FUNCTION.

5. ELECTRICAL INSTALLATION (CONT’D)

6. TABLE 1 - CABLE SIZE TABLE

Power Current

(kW) (A)

220V ~

50/60 Hz

Conductor Size (csa)

mm Conduit Cable Flexible Cable

On/ Off Fuse /

Switch (A) MCB (A)

2.4 10.9 2.5 7 / 0.67mm 50 / 0.25 mm 20 20

3.5 15.9 2.5 7 / 0.67mm 50 / 0.25 mm 20 20

4.5 20.5 2.5 7 / 0.67mm 50 / 0.25 mm 32 32

6.0 27.3 4.0 7 / 0.85mm 56 / 0.30 mm 32 32

Voltage

(AC)

3.6 15.0 4.0 7 / 0.85mm 56 / 0.30 mm 20 20

240V ~

50/60 Hz

(Malaysia Model)

METHOD OF ALIGNMENT WHEN REPLACING FRONT COVER

Cable

Fig. 4

Brown or Red = Line (L)

Blue or Black = Neutral (N)

Green or Green/ Yellow = Earth ( )

Fig. 5

Fuse Distributor Board

Miniature Circuit Breaker (MCB)

ON/OFF Double Pole Switch

Double PVC cable

NOTE:

Refer to TABLE 1 for electrical loading and

correct size of wire conductor

Fig. 6

Front CoverFig A Fig B

1 2

3 4 5

(2.2 ℓ/Min for 4.8kW & 2.5 ℓ/min for 6.0kW model

only)

/ 2.2 ℓ/Min for 4.8kW & 2.5 ℓ/min for 6.0kW model

only) to trigger the flow switch.

REV0

Fig. 3

SHOWER SET INSTALLATION DIAGRAM

PVC Hose

Shower

Screw

Shower

Holder

Cover

Shower

Holder

Head

BRACKET ACCESSORIES

3.5. Open the Shower Holder cover, mark 2 screw point of the Shower Holder beside the Electric Water Heater.

It is recommended that the top of the portion is in level the top Electric Water Heater. After screw the Shower

Holder, put back the shower holder cover.

EWE351PX-DWX5

EWE451PX-DWX5

3.8 17.3 2.5 7 / 0.67mm 50 / 0.25 mm 20 20

4.8 21.8 2.5 7 / 0.67mm 50 / 0.25 mm 32 32

2.4 If the Red (POWER) Indicator does not go off

when you turn off the water, switch OFF the

mains supply and contact Electrolux Consumer

Care Centre for repair service.Special skill is

required for repairing.

NEVER try to repair the unit by yourself.

Fig. 1

OFF

Position

this Way

connect to

water outlet

connection

Position

this Way

7. TEST RUN

7.1 Turn on the water supply and 3 in 1

Stop Valve, the water will flow through the

Handshower.

7.2 Switch on the power supply. The 3

LED Indicator light shall run ON/OFF 3

times in sequences to indicate the set are

self checking.

If the

Electric Water Heater

is not earthed

properly, the Earth Led indicator light will

OFF, during usage or standby. Earth Led

indicator light also OFF if Line & Neutral

reverse connection.

7.4 The

Electric Water Heater

might not be

hot enough even at the ‘MAX’ position if

incoming water supply from the mains is too

cold or the pressure of water is too high. In

this case, you may adjust the 3 in 1 Stop Valve

to reduce the water inflow in order to get the

desired showering temperature.

7.5 Check the Built-in ELCB as following:

- Press the “TEST” Button, the Built-in ELCB

should trip and cut off the power supply,

ELCB and Power Indicators should light off.

-Press the “RESET” Button, the 3 LED

Indicator light shall run ON/OFF 3 times in

sequences to indicate self checking as in 7.2

above and the

Electric Water Heater

should

resume normal function, the Green LED

Indicator should light on. If procedures stated

above prevailed, the ELCB is functioning in

normal condition.

7.6 Move the Handshower to the desired

angle. A ratchet mechanism in the Shower

Holder will hold the Handshower in selected

position.

7.7 It is unnecessary to turn the Temperature

Control Knob to “OFF” position when the

Instant Hot Shower is not in use.

7.8 Switch OFF the power supply after shower.

(Recommended flow rate of below 6litre/min)

8. HANDSHOWER SPRAY

9. MAINTENANCE

9. MAINTENANCE - continue

Clean the Handshower Head holes by using the soft brush from time to time.

(Recommended once a week)

Note: Take care not to damage the holes of the Handshower Head during cleaning.

Fig. 8 Fig. 9

FILTER UNIT CLEANING

OPEN

INTERNAL

STRAINER

OPEN CLOSE

FLOW REGULATOR

MESH FILTER

BUILT-IN FILTER

9.1 TEST THE ‘ELCB’ REGULARLY

(This procedure is highly recommended test at

least once a month)

9.2 CLEAN THE FILTER REGULARLY

Clean the Mesh Filter regularly to prevent

blockage (Fig. 8) . Remove the Built-in Filter by

turning its cap anticlockwise. Whenever need

Read the section ‘ SAFETY INFORMATION ’ first.

WARNING!

9.3 If the Red (POWER) Indicator does not

go off when you press the ELCB Test Button,

switch OFF the mains supply and contact

Electrolux Consumer Care Centre for repair

service. Special skill is required for repairing.

NEVER try to repair the unit by yourself.

9.4 CLEANING PRECAUTION !

Do not use thinner,alcohol,petrol or any other

organic solutions to clean the set. Use only

damped cloth with mild detergent.

flush the internal stainer with water to remove

any trapped sediments. Whenever fixing back

the Built-In Filter, beware of the alignment of

Internal Strainer. Use the protruded guideline

within Stop Valve to position the Internal

Strainer.

10. WIRING DIAGRAM

WIRING DIAGRAM -WITH ELCB, NO PUMP DPDT MODEL

11. ELECTRICAL SPECIFICATION

Note : The specification, actual product’s cosmetic design and accessories parts shown are

correct at the time of printing and may be subjected to change without prior notice.

1.3 kg

ELECTRONIC POWER CONTROLTYPE

LELECTRICA LOADING

Min. WATER FLOW RATE

WATER CONNECTION

DIMENSIONS

NETT WEIGHT

1/2” BSP SINGLE POINT

SYSTEM

6.0 Bar (0.6 MPa ;

Max. INLET WATER PRESSURE

Min. INLET WATER PRESSURE

0.1 Bar (10 kPa ;

87.02 psi)

1.45 psi)

* Manual Reset (90° C Thermostat)Thermostat

For Models rated 4.8kW and below, thermostat is manually resetable.

For models rated 6.0kW and above, thermostat needed to be replaced once permanently tripped.

3.5kW 15.9A 220V a.c. 50/60Hz

4.5kW 20.5A 220V a.c. 50/60Hz

2 Litre / min

CONSUMER CARE

Indonesia

Hotline service: 0 041119999 8

PT. Electrolux Indonesia

Electrolux Building

Jl.Abdul Muis No.34, Petojo Selatan,

Gambir Jakarta Pusat 10160

Email:customercare@electrolux.co.id

SMS WA : 0 12. 0 . 63 & 8 8 88 88

Malaysia

Consumer Care Center Tel: 1300- -11-22 88

Electrolux Home Appliances Sdn. Bhd.

Corporate Office Address: Unit T2-7, 7th Floor, Tower 2 ,

Jaya33 Hyperoffice, No. 3, Jalan Semangat, Seksyen 13,

46100 Petaling Jaya, Selangor

Office Tel : (+60 3) 7 43 5999 8

Office Fax : (+60 3) 7955 5511

Consumer Care Center Address: Lot C6, No. 2 , 8

Jalan 15/22, Taman Perindustrain Tiong Nam,

40200 Shah Alam, Selangor

Consumer Care Center Fax : (+60 3) 5524 2521

Email : malaysia.customercare@electrolux.com

Philippines

Consumer Care Center Toll Free : 1- 00-10- 45-CARE 2273 8 8

Consumer Care Hotline : (+63 2) 45 CARE 2273 8

Electrolux Philippines, Inc.

10th Floor. W5th Avenue Building

5th Avenue Corner 32nd Street

Bonifacio Global City,

Taguig Philippines 1634

Trunkline: +63 2 737- 4756

Website : www.electrolux.com.ph

Email : wecare@electrolux.com

Singapore

Consumer Care Center Tel: (+65) 6727 3699

Electrolux S.E.A. Pte Ltd.

1 Fusionopolis Place,

#07-10 Galaxis, West Lobby

Singapore 13 522. 8

Office Fax : (+65) 6727 3611

Email : customer-care.sin@electrolux.com

Thailand

Consumer Care Tel : (+66 2) 725 9000

Electrolux Thailand Co., Ltd.

Electrolux Building 14th Floor

1910 New Phetchaburi Road,

Bangkapi, Huai Khwang, Bangkok 10310

Office Tel : (+66 2) 7259100

Office Fax : (+66 2) 7259299

Email : customercarethai@electrolux.com

Vietnam

Consumer Care Center Toll Free : 1 00-5 - -99 8 8 88

Tel : (+ 4 ) 3910 5465 8 8

Electrolux Vietnam Ltd.

Floor 9th, A B Tower &

76 Le Lai street - Ben Thanh Ward - District 1

Ho Chi Minh City ，Vietnam

Office Tel : (+ 4 ) 3910 5465 8 8

Office Fax : (+ 4 ) 3910 5470 8 8

Email : vncare@electrolux.com

Hongkong

Tel: (+ 52) 203 029 8 8 8

Dah Chong Hong, Ltd. - Service Centre

8/F., Yee Lim Godown Block C

2-2 Kwai Lok Street, Kwai Chung, N.T.8

6 7 8

9 10

.Fig 7

STANDARD SINGLE SPRAY

7.3 Turn the Temperature Control Knob to

‘ON’, the Red indicator light (HEATER POWER)

will turn on, (ELCB/Power Led indication are

combine Led indicator light- ELCB is GREEN

& Power is RED) hot water will flow out within

a few seconds. The more Temperature Control

Knob being turned in clockwise direction, the

hotter is the water.

Turn on the power supply and water supply , both

Red (HEATER) and Green (ELCB) Indicators will

light up if the Temperature Control Knob is in ‘ON’

position. Press the ELCB Test Button, both

HEATER and ELCB Indicators should go off.

Press the Reset Button to resume the power

supply.

WE’RE THINKING OF YOU

Thank you for purchasing an Electrolux appliance. You’ve chosen a product that brings with

it decades of professional experience and innovation. In genious and stylish, it has been

designed with you in mind. So whenever you use it, you can be safe in knowledge that

you’ll get great results every time. Welcome to Electrolux.

Visit our website to:

Get usage advice, brochures, trouble shooter, service information:

www.electrolux.co.th

https://www.electrolux.co.th/support/register-warranty/

Buy Accessories, Consumables and Original spare parts for your appliance:

www.electrolux.com/shop

CONSUMER CARE AND SERVICE

We recommend the use of original spare parts.

When contacting Service, ensure that you have the following data available.

The information can be found on the rating plate. Model, PNC, Serial Number.

(Right side of unit).

Warning/ Caution-Safety information.

General information and tips.

Environmental information.

Subject to change without notice.

LINE

NEUTRAL

Power On/Off

Temperature

Control

TRIAC

Lout

Nout

in )

Auto-Reset * Manual-Reset

Power Supply

220 V~a.c.

Double Action Thermostat

Electronic

ELCB,15mA

Sensitivity

Reset

Test

Relay 1

Relay 2

Heater Control

On/Off Switch

189 (W) X 270 (H) X 102 (T) mm

Specyfikacje produktu

Marka:	Electrolux
Kategoria:	Kotły i bojlery
Model:	EWE451PX-DWX5

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Electrolux EWE451PX-DWX5, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Kotły i bojlery Electrolux

Electrolux EWH30SIEEC Instrukcja

30 Września 2024

Electrolux EWH100SIEEC Instrukcja

29 Września 2024

Electrolux EWH100SIBEEEC Instrukcja

29 Września 2024

Electrolux EWH80SI Instrukcja

29 Września 2024

Electrolux EWH80SIBEEEC Instrukcja

29 Września 2024

Electrolux EWH30SIBEEEC Instrukcja

29 Września 2024

Electrolux EWH80SISEEEC Instrukcja

29 Września 2024

Electrolux EWH-S Instrukcja

5 Lipca 2024

Electrolux EWH-SL Instrukcja

4 Lipca 2024

Electrolux EWE601LX1DPX2 Instrukcja

2 Lipca 2024

Instrukcje Kotły i bojlery

Najnowsze instrukcje dla Kotły i bojlery

Sencor SWK 7706GD Instrukcja

14 Października 2024

Hotpoint HE30S01SAG Instrukcja

13 Października 2024

Nibe VPA 300/200 E Instrukcja

9 Października 2024

Noritz NC199OD Instrukcja

9 Października 2024

Nibe Melite 120 Instrukcja

8 Października 2024

Nibe VPB 500-1000 Instrukcja

8 Października 2024

MicroHeat CFEWH SERIES 2 Instrukcja

8 Października 2024

Elba EWH-E3881(SW) Instrukcja

8 Października 2024

Elba EWH-E3885DC(SG) Instrukcja

8 Października 2024

Elba EWH-G3661(MB) Instrukcja

8 Października 2024