Instrukcja obsługi Electrolux EFT7516K

Electrolux Okap wyciągowy EFT7516K

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Electrolux EFT7516K (11 stron) w kategorii Okap wyciągowy. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/11
USER MANUAL : COOKER HOOD
EFT7516K
EFT7516X
EFT9516K
EFT9516X
Description................................................1
Installation ................................................1
Installation Ducting Version ... ....................1
Installation Filtering Version .. ....................2
Operation ................................................. 3
Warning ....................................................3
Wiring Diagram .........................................4
Diagram ....................................................4
Warranty Condition ...................................8
CONTENTS
DESCRIPTION
The hood may be installed in the filtering or the ducting version.
Ducting version (Fig.1): The hood aspirates the kitchen air saturated with fumes and odour,
passes it through the grease filters and expels it to the outside through an outlet pipe. With
this version the charcoal filters are not required.
Decide from the outset on the type of installation (filtering or ducting). For greater efficiency,
we recommend you install the hood in the ducting version (if possible).
Filtering version (Fig.2): The hood aspirates the kitchen air saturated with fumes and odour.
Purifies it through the grease filters and charcoal filters and returns clean air into the room.
For constant efficiency, the charcoal filters must be replaced periodically.
INSTALLATION
-Before beginning installation, to better handle the hood, we advise removing the grease
filters.
-To remove the grease filter/s (Fig.3), in line with the handle, push the stop inwards and pull the
filter down.
INSTALLATION IN DUCTING VERSION:
-Before fixing, the outlet pipe for air evacuation to the outside must be installed. Use an outlet
pope with: - minimum indispensable length; -Minimum possible bends (maximum angle of
bend:90°); -certified material (according to the state); _ an as smooth as possible inside. It is
also advisable to avoid any drastic changes in pipe cross-section (recommended diameter:
155mm).
-Decide on the position of the hole for the air outlet: The hole may be in the wall or the ceiling,
according to your requirements, but must be in vertical line with your hood. Bear in mind that
the hood just expel air through the top opening A (Fig.4).
-Mounting the air outlet adapter to the top opening A by securing two screws. Bear in mind that
the opening B(Fig.4) must be closed by two ventilation cover with 4 screws(Fig.5) then insert
the nameplate into the ventilation covers(Fig.6).
-Drill the hole in the wall for the air outlet (163 mm diameter) referring to Fig.7 where the
measurements for the various possibilities are indicated.
-Prepare a suitable power supply. For the electrical connection, follow all the other instructions
on the other instructions on the page 3.
-Proceed with fixing the hood: Based on your requirements, you can fit the hood on the wall or
on a wall unit of your kitchen. IMPORTANT: Respect the distance between the hob and lower
part of the hood which must be at least 650 cm.
-Fixing to the wall:
Before fixing the hood to the wall, mount two mounting brackets to the hood
from two side with 4 screws provided(Fig.8) and drill a hole of 163mm diameter in the wall unit
(Fig.7). In any case, check the position of the power outlet and consider where the power
cable will run, since a hole might have to be made in the wall unit to accommodate it. Draw a
line on the wall in vertical line with your hob. Mark the2 holes to be drilled in the wall,
respecting the distances indicated in Fig. 7; Make the 2 holes and fit the 2 screw anchors
provided then without screwing that 2 of screws down completely. Hang the hood on the 2
screws; tighten the 2 screws completely. Now proceed with connecting a flexible tube to the
hood outlet adapter tight well by mounting 2 screws. Tube is not provided. Make the electrical
connection.
Page1

Specyfikacje produktu

Marka: Electrolux
Kategoria: Okap wyciągowy
Model: EFT7516K

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Electrolux EFT7516K, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Okap wyciągowy Electrolux

Electrolux

Electrolux EFP9500XA Instrukcja

3 Stycznia 2025
Electrolux

Electrolux EFP6500XA Instrukcja

8 Października 2024
Electrolux

Electrolux DMSL8335UO Instrukcja

5 Października 2024
Electrolux

Electrolux DMSL8330AO Instrukcja

5 Października 2024
Electrolux

Electrolux ERCE9025BK Instrukcja

4 Października 2024
Electrolux

Electrolux LFE116W Instrukcja

4 Października 2024
Electrolux

Electrolux EFG50300W Instrukcja

24 Września 2024
Electrolux

Electrolux EFT635X Instrukcja

24 Września 2024
Electrolux

Electrolux EFC60151W Instrukcja

24 Września 2024
Electrolux

Electrolux EFC90990X Instrukcja

24 Września 2024

Instrukcje Okap wyciągowy

Najnowsze instrukcje dla Okap wyciągowy

Silverline

Silverline PRW 800 Instrukcja

15 Stycznia 2025
Silverline

Silverline STW 600 C Instrukcja

15 Stycznia 2025
CATA

CATA F 2260 X Instrukcja

15 Stycznia 2025
Bosch

Bosch DWK09M760 Instrukcja

15 Stycznia 2025
Zanussi

Zanussi ZHC 1000 x Instrukcja

15 Stycznia 2025
AEG-Electrolux

AEG-Electrolux X69453MVO Instrukcja

15 Stycznia 2025
Beko

Beko CWB 9441 Instrukcja

15 Stycznia 2025
Bosch

Bosch DWB097A51 Instrukcja

15 Stycznia 2025
Elica

Elica EST630SS Instrukcja

15 Stycznia 2025
Atag

Atag WS90211EM Instrukcja

15 Stycznia 2025