Instrukcja obsługi Electro Harmonix Nano Battalion
Electro Harmonix
wzmacniacz gitarowy
Nano Battalion
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Electro Harmonix Nano Battalion (4 stron) w kategorii wzmacniacz gitarowy. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/4

NANO BATTALION
BASS PREAMP + OVERDRIVE
Congratulations on your purchase of the Electro-Harmonix Nano
Battalion. The all-analog circuitry of the Nano Battalion provides you
with an amazing variety of bass tones in a sturdy and compact pedal. At
the core of the Nano Battalion’s tone is a versatile MOSFET drive circuit
that can range from a subtle, light overdrive to fully saturated distortion.
A flexible three band equalizer includes a three way EQ Position switch
to select where the EQ falls in the pedal’s signal path.
The Nano Battalion features a normal ¼” input, plus a ¼” output that
can output either a normal, unbalanced signal (with a normal TS cable)
or a balanced signal (with a TRS cable) to go right into a mixing console
or recording interface. The Nano Battalion features buffered bypass and
runs on a standard 9.6VDC center negative supply, drawing 45mA.
- Using the Nano Battalion -
Plug the 9VDC adapter into the jack on the top of the Nano Battalion.
The unit must be powered to pass signal even in bypass. Connect an
instrument cable from your bass into the jack. Insert a normal INPUT
TS instrument cable between the jack and a suitable amplifier, OUTPUT
or insert a TRS cable (or TRS to male XLR cable) between the OUTPUT
jack and a suitable mixing console or recording interface. Click the
BYPASS footswitch to engage the Nano Battalion. The LED lights to
indicate that the unit is active.
WARNING:
Your
Nano Battalion
comes equipped with an Electro
-
Harmonix 9.6DC
-
200BI
power supply (same as used by Boss
®
& Ibanez
®
: 9.6 Volts DC 200mA). The Nano
Battalion requires at 9VDC with a center negative plug. Use of the wrong adapter 45mA
or a plug with the wrong polarity may damage your Nano Battalion and void the warranty.

- Main Control -
BYPASS Footswitch & LED – The LED illuminates when the effect is
engaged. The LED will not light if the Nano Battalion is bypassed. Press
the footswitch to toggle between effect on and buffered bypass mode.
VOL Knob – Sets master output level of the pedal.
BLEND Knob – Sets the ratio between clean signal and distorted signal.
Turn BLEND up for more distorted signal.
DRIVE Knob – Sets the intensity and saturation of the distortion.
TONE Knob – Cuts high frequencies from the distortion as you turn the
knob down.
EQ CONTROLS:
TREBLE Knob – Boost or cut high end. No effect when the knob is at
50%. Boosts/cuts frequencies starting above 1kHz. Maximum boost/cut
about +/-12dB around 5kHz.
BASS Knob – Boost or cut low end. No effect when the knob is at 50%.
Boosts/cuts frequencies starting below 200Hz. Maximum boost/cut
about +/-12dB around 60Hz.
MID Switch – No effect when the switch is in the middle position. In
the upwards position, 9dB boost around 500Hz. In the downwards
position, 9dB cut around 500Hz.
- EQ POS. & Signal Path -
The EQ POS switch determines where the EQ (TREBLE, BASS, and MID
controls) falls in the Nano Battalion’s signal path. In all cases, the TONE
control comes immediately after the distorted signal, and the VOL control
is last in the signal path. There are three EQ POS modes, illustrated on
the next page.

- FCC COMPLIANCE -
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. If the device
is not installed and used in accordance with the instructions, it may
cause harmful interference to radio communications and void the user's
authority to guarantee the equipment.
Note:
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help .
Modifications not expressly approved by the manufacturer could void the
user's authority to operate the equipment under FCC rules.
The CE logo indicates that this product has been tested and shown to conform
with all applicable European Conformity directives.
DIST MODE:
In DIST mode the EQ comes after the distortion signal, having a strong
effect on the sound of the distorted signal. The clean signal is not
affected by the EQ at all.
INPUT MODE:
In INPUT mode the EQ comes first in the signal path, affecting both the
clean signal and the signal fed into the distortion. Boosting frequencies
in this mode can help drive the distortion signal to a more saturated
tone.
DRY MODE:
In DRY mode the EQ affects the clean signal, but doesn’t affect the
distorted signal at all.
Specyfikacje produktu
Marka: | Electro Harmonix |
Kategoria: | wzmacniacz gitarowy |
Model: | Nano Battalion |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Electro Harmonix Nano Battalion, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje wzmacniacz gitarowy Electro Harmonix

9 Września 2024

8 Września 2024

8 Września 2024
Instrukcje wzmacniacz gitarowy
- wzmacniacz gitarowy Yamaha
- wzmacniacz gitarowy Roland
- wzmacniacz gitarowy Behringer
- wzmacniacz gitarowy Boss
- wzmacniacz gitarowy Line 6
- wzmacniacz gitarowy Empress Effects
- wzmacniacz gitarowy Marshall
- wzmacniacz gitarowy Blackstar
- wzmacniacz gitarowy TC Electronic
- wzmacniacz gitarowy Peavey
- wzmacniacz gitarowy ART
- wzmacniacz gitarowy Hartke
- wzmacniacz gitarowy Palmer
- wzmacniacz gitarowy VOX
- wzmacniacz gitarowy Harley Benton
- wzmacniacz gitarowy Fender
- wzmacniacz gitarowy Mooer
- wzmacniacz gitarowy Fishman
- wzmacniacz gitarowy Radial Engineering
- wzmacniacz gitarowy API Audio
- wzmacniacz gitarowy SPL
- wzmacniacz gitarowy Budda
- wzmacniacz gitarowy Ampeg
- wzmacniacz gitarowy Valeton
- wzmacniacz gitarowy Hughes & Kettner
- wzmacniacz gitarowy Laney
- wzmacniacz gitarowy Ashdown Engineering
- wzmacniacz gitarowy Dimavery
- wzmacniacz gitarowy Markbass
- wzmacniacz gitarowy NUX
- wzmacniacz gitarowy Orange
- wzmacniacz gitarowy AER
- wzmacniacz gitarowy EBS
- wzmacniacz gitarowy Rivera
- wzmacniacz gitarowy Suhr
- wzmacniacz gitarowy Two Notes
- wzmacniacz gitarowy GR Bass
- wzmacniacz gitarowy Voodoo Lab
- wzmacniacz gitarowy Bugera
- wzmacniacz gitarowy AMT
- wzmacniacz gitarowy DV Mark
- wzmacniacz gitarowy DACS Audio
Najnowsze instrukcje dla wzmacniacz gitarowy

11 Stycznia 2025

9 Stycznia 2025

9 Stycznia 2025

8 Stycznia 2025

30 Grudnia 2025

29 Grudnia 2024

29 Grudnia 2024

29 Grudnia 2024

27 Grudnia 2024

25 Grudnia 2024