Instrukcja obsługi Ei Electronics Ei146 Optical

Ei Electronics Detektor dymu Ei146 Optical

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Ei Electronics Ei146 Optical (2 stron) w kategorii Detektor dymu. Ta instrukcja była pomocna dla 15 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

Shannon Free Zone, Shannon, Co. Clare, Ireland.

Ph. Fx. +353 61 471277 +353 61 471053

Email. eielectronics@eiltd.ie

Web: www.eielectronics.com

E & OE As our policy is one of continuous product development, we reserve the right to alter product details without prior notice. Ei146 DataSht RevA

Model Ei146 Optical

 Easi-Fit base

 9V Alkaline Battery back up

 High performance optical chamber with integral

insect screen

 Test/Hush button

 Advanced suppression and calibration technology

 Interconnectable to other Ei mains powered alarms

 Built in auto self test feature

 Low power cell warning

 Kitemarked to BS EN14604:2005

 5 year guarantee

Product Description

The Ei146 is an Optical Smoke Alarm that runs on 230V

AC mains power, and has a 9V alkaline battery back up

in the event of mains failure. The 9V battery will last for

up to 4 years in standby mode, and capable of powering

the smoke detector for up to 2 years in the event of

mains failure.

The Ei146 is supplied with the Easi-Fit base that allows

very quick and simple installation of the smoke alarm,

combined with simple detector head removal and

replacement. The Easi-Fit base automatically connects

both mains power and battery as the detector head

slides on to the Easi-Fit base.

The Ei146 has other advanced features such as high

performance optical chambers ﬁtted with integral insect

screens to reduce the chances of false alarms, as well

as the ability to interconnect up to twelve alarms to allow

all alarms to sound if just one of the interconnected

alarms should be triggered.

The Ei146 has built in circuitry to aid suppression of

voltage transients and RF interference to further reduce

the chances of false alarms under such conditions.

Operation

 The green indicator will illuminate to show mains

power is present

 The red indicator will ﬂash every 40 seconds to

show that the detector has performed an automatic

self test

 The red indicator will ﬂash rapidly to show an alarm

condition for the smoke detector

 The “Test/Hush” button will either silence false

alarms or perform a unit self test

 In “Test” mode the alarm will perform a self test and

sound the horn

 In “Hush” mode the alarm enters a ten minute period

of reduced sensitivity to overcome false alarm

conditions, and will then automatically reset itself

 When interconnected to other Ei mains powered

alarms, an alarm on one detector will trigger all other

interconnected alarms within one second (only the

triggered alarm will ﬂash a red indicator)

 The smoke detector will emit a beep and ﬂash the

red light every 40 seconds to indicate that the

battery back up is depleted and needs replacing

MAINS POWERED 230V~

9V Alkaline Battery Back- Up

Shannon Free Zone, Shannon, Co. Clare, Ireland.

Ph. Fx. +353 61 471277 +353 61 471053

Email. eielectronics@eiltd.ie

Web: www.eielectronics.com

E & OE As our policy is one of continuous product development, we reserve the right to alter product details without prior notice. Ei146 DataSht RevA

Model Ei146 Optical

Installation & Placement

Wiring for Interconnected Alarms

Be very careful about correctly wiring the alarms as mixing Live and Neutral

will blow/damage interconnected alarms.

Alarms should be placed in accordance with the general guidelines shown in

the diagram above. These recommendations are based on the problem of

areas of “dead air” close to corners of rooms and apexes of ceilings, which

could result in the prevention of smoke reaching the smoke detector

Please consult instruction booklet for speciﬁc installation details

Important Precaution:

Do not install the actual smoke/heat alarm

itself in new or renovated buildings until all

work is completed (including ﬂoor coverings)

and the building has been fully cleaned. The

wiring can be installed when appropriate.

(Excessive dust and debris from building work

can contaminate the smoke chamber and

cause problems, and it will also invalidate the

guarantee). If it must be installed, cover it

completely, particularly around the edges, with

a dust cover (eg. a plastic bag), until all

cleaning is ﬁnished.. Connect wires to the unit

as in wiring diagram. All wiring must comply

with local codes.

Technical Speciﬁcation

Sensor Optical, uses light scatter from

smoke

Sensitivity: Complies with BS 5446 Part 1:

2000

Source: Contains no radioactive material

Airspeed: Essentially immune to the eﬀect

of airspeed.

Button Test: Simulates the eﬀect of smoke and

checks chamber, electronics and

horn.

Ambient Light: Chamber housing design and

compensation overcomes

problems with stray light.

AutomaticSelf-Test: Smoke Chamber is tested every 40

Sec. and unit beeps (without LED

ﬂash) if it is degraded.

Insect Screen: Prevents insects or debris entering

chamber (1.00mm mesh size)

Supply Voltage: 230V AC

Battery back up: 9V Alkaline Battery

Speciﬁcations are subject to change

Power-On Indicator: Continuous green LED

Alarm: Electronic Piezoelectric horn

Alarm Sound Output: 85dB (minimum) at 3m

Alarm Status: Red LED ﬂashes every second on

unit sensing ﬁre

Temperature Range: 0° to 40°C

Humidity Range: 15% to 95% Relative Humidity

Interconnect: Up to 12 interconnected mains

powered easi-ﬁt smoke or heat

alarms, along with an EI128 relay

base

Fixing: Easi-Fit mounting base

Plastic material: UL94VO ﬂame retardant

Dimensions: 152mm x 50mm depth

Weight: 345g

Warranty: 5 year (limited) warranty

Approvals: Kitemarked to BS EN14604:20005

CE Approved

Specyfikacje produktu

Marka:	Ei Electronics
Kategoria:	Detektor dymu
Model:	Ei146 Optical

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Ei Electronics Ei146 Optical, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Detektor dymu Ei Electronics

Ei Electronics Ei3024 Instrukcja

24 Września 2024

Ei Electronics Ei630IRF Instrukcja

17 Września 2024

Ei Electronics Ei261EN Instrukcja

21 Sierpnia 2024

Ei Electronics Ei166RC Instrukcja

6 Lipca 2024

Ei Electronics Ei146 Optical Instrukcja

6 Lipca 2024

Ei Electronics Ei146 Instrukcja

4 Lipca 2024

Ei Electronics Ei225E Instrukcja

4 Lipca 2024

Ei Electronics Ei184 Instrukcja

2 Lipca 2024

Instrukcje Detektor dymu

Najnowsze instrukcje dla Detektor dymu

First Alert HD6135FB Instrukcja

14 Października 2024

Kidde 3SFWR Instrukcja

9 Października 2024

Kidde KF30R Instrukcja

9 Października 2024

Kidde P4010ACS-WCA Instrukcja

9 Października 2024

Kidde P4010DCSCO-WCA Instrukcja

9 Października 2024

Kidde i12020CA Instrukcja

9 Października 2024

Kidde i12040CA Instrukcja

9 Października 2024

Kidde KF20R Instrukcja

9 Października 2024

Kidde CP9000CA Instrukcja

9 Października 2024

Kidde Pi2010CA Instrukcja

9 Października 2024