Instrukcja obsługi Dynaudio DA-BM6A

Dynaudio monitor DA-BM6A

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Dynaudio DA-BM6A (6 stron) w kategorii monitor. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/6
DA-BM6A
OWNERS MANUAL
Congratulations on your purchase of the Dynaudio Acoustics BM6A monitor system. With the
right care and attention it will give you many years of trouble free audio reproduction. It is
most important, however, that you take a few minutes at this early stage in your BM6A’s life to
read the following paragraphs. They contain essential information to enable you to get the
best from your monitors.
Electrical Safety Warning
This unit is supplied with a 3 wire power cord. Under no circumstances should the
earth wire be disconnected.
To prevent possibility of shock hazard do not expose the unit to moisture
There are no user serviceable parts inside. Do not open cover. Refer servicing to
qualified personnel only
Ensure correct mains voltage and fuse are selected before connection to mains
BM6A Owner’s Manual - Issue 2 Page 2
November 1997
Setting Up
Mai
Mai
Mai
MaiMains Po
ns Po
ns Po
ns Pons Power Co
wer Co
wer Co
wer Cower Connect
nnect
nnect
nnectnnectio
io
io
ioions
ns
ns
nsns
Mains power is applied via a fused IEC inlet. The unit must be earthed. The voltage selector
switch is used to match the unit to the mains voltage in your territory. The mains fuse must be
the correct value for the voltage selected, 115V requires a T3.15A fuse while 230V requires a
T1.6A fuse. The ‘T’ signifies a slow blow type fuse.
You must ensure that the correct voltage and fuse have been selected before
switching the unit on.
Audio Co
Audio Co
Audio Co
Audio CoAudio Connect
nnect
nnect
nnectnnectio
io
io
ioions
ns
ns
nsns
Audio input is via a female XLR connector. The input is electronically balanced with +ve on
pin 2, -ve on pin 3 and ground on pin 1. If your signal source is unbalanced it is usual to
connect the unused signal pin (i.e. Pin 3) to ground. This is normally done inside the
connecting cable. For best results use only good quality screened cables and connectors.
Your local dealer will be able to advise you
Positioning
Positioning
Positioning
PositioningPositioning
The BM6A is designed primarily as a ‘nearfield’ monitor and would normally be positioned
1-3m from the listener. They can be mounted on stands or on the meter bridge of the console
(providing this is substantial enough). For best results the speakers should be ‘aimed’ at the
listener in both vertical and horizontal planes.
In any situation ensure that there is adequate space for ventilation around the heatsink.
BM6A Owner’s Manual - Issue 2 Page 3
November 1997
Operation
Controls
Controls
Controls
ControlsControls
Level switch. This sets the input sensitivity of the unit. The +4 position is intended for
professional use and means that full power is reached with an input level of
+4dBm (balanced). The -10 position is intended for semi-professional or
domestic use and means that full power is reached with an input level of
-10dBm (unbalanced).
HF Trim. This control allows the high frequency level to be adjusted. The control
works from 3kHz upwards and has a range of 5dB (see figure 1).
LF Trim. This control allows the low frequency level to be adjusted. The control works
from 100Hz downwards and has a range of 5dB (see figure 1). This section
uses a special equaliser design which effectively swaps bandwidth for power.
As you turn the LF trim level down the low frequency extension is improved.
The trim controls are intended to allow the user to make some adjustment of the speaker
response to accommodate personal tastes and variations in acoustic environment.
Figure 1 - Trim Control Response
Indicators
Indicators
Indicators
IndicatorsIndicators
There are two LED indicators on the front baffle of the BM6A.
The right hand one is the power/fault indicator. On switching the unit on this will shine red for
about ten seconds and then turn green to indicate normal operation. If for any reason the
amplifier protection circuitry is engaged the LED will turn back to red.
The left indicator is a true clip indicator and lights when the low frequency amplifier clips. It is
acceptable to run the system with this lighti running the system withng occasionally but avoid
this lighting most of the time
Running In
Running In
Running In
Running InRunning In

Specyfikacje produktu

Marka: Dynaudio
Kategoria: monitor
Model: DA-BM6A

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Dynaudio DA-BM6A, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje monitor Dynaudio

Dynaudio

Dynaudio BM6A Instrukcja

28 Grudnia 2024
Dynaudio

Dynaudio LYD 48 Instrukcja

12 Września 2024
Dynaudio

Dynaudio DA-BM6A Instrukcja

12 Września 2024

Instrukcje monitor

Najnowsze instrukcje dla monitor

Philips

Philips Brilliance B-line 241B4LPYCS Instrukcja

23 Marca 2025
Viewsonic

Viewsonic VX2428J2 Instrukcja

22 Marca 2025
ProDVX

ProDVX SD-18 Instrukcja

21 Marca 2025
ProDVX

ProDVX SD-15 Instrukcja

21 Marca 2025
AOC

AOC CQ32G4 Instrukcja

20 Marca 2025
Viewsonic

Viewsonic XG275D1-4K Instrukcja

19 Marca 2025
Viewsonic

Viewsonic XG275D-4K Instrukcja

19 Marca 2025
Philips

Philips 27E1N1600AM Instrukcja

17 Marca 2025
Acer

Acer EI322QURV Instrukcja

14 Marca 2025
Acer

Acer CS272K Instrukcja

14 Marca 2025