Instrukcja obsługi DSC TL250

DSC nieskategoryzowany TL250

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla DSC TL250 (2 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 14 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

Contact your DSC distributor

www.dsc.com

1-888-888-7838

Supported by PC1864, PC1832, PC1616, Power864

™and MAXSYS®

control panels via built-in PC-Link, or stand-alone mode for all

other control panels

2-way, always-on IP communication

Works over local LAN/WAN network or the Internet

128-bit AES encryption (NIST approved)

Supports DHCP (dynamic IP addresses)

Reports events to 2 different receiver IP addresses

Polling and hardware substitution protection

Programmable heartbeat timer allows you to adjust the interval

that the heartbeat signal is sent from the TL250 module to the

central station IP receiver

Low network bandwidth requirements

Compatible with 10/100BaseT networks

4 on-board programmable inputs (expandable to 12

using PC5108 zone expander module)

2 programmable voltage outputs

Programmable through the panel keypad or T-Link Console software

Software upgrades via network

Download control panel via Internet with DLS2002SA software

UL AA High-Line Security and ULC Level 3/4/5 listed

T-Link TL250 Internet alarm communicators create fully

supervised security solutions between protected

premises and central monitoring stations. The simple-to-

install modules save end-users money by taking advantage of

their existing networks to provide secure Internet

communications over a private network (LAN/WAN) or the

Internet, between the control panel and the Sur-Gard

™System

ll/III central station receivers. This method provides flexibility

and an always-on, two-way line of communication. The TL250

communication stream is small and requires only a limited

amount of network bandwidth. This ensures that the integrity

of the data being transferred never becomes compromised. To

reduce security risks, the TL250 utilizes

industry-leading, 128-bit AES encryption, polling and hardware

substitution protection.

ttt t

Product Features:

tttt ttt tt t

DSC T-LinkTM Internet Alarm Communicator TL250

Distributed by:

For product information

www.dsc.com

Product specifications and availability subject to

change without notice. Certain product names

mentioned herein may be trade names and/or

registered trademarks of other companies.

P/N 29007074 R003 Printed in Canada

Value Added

To ensure dependable and timely event notification, the TL250 is

capable of reporting to two different receiver IP addresses—a

back-up feature that allows communication to continue in the

event one of the IP addresses is inaccessible. The TL250 can also

be programmed to communicate events to two different e-mail

addresses. These e-mail addresses can be associated with a

personal computer, pager, enabled mobile phone or PDA.

Flexibility

Programming the TL250 can be accomplished locally using the

control panel keypad or T-Link Console software over the IP

network connection made directly to TL250’s Ethernet port.

By interfacing to TL250’s four on-board programmable inputs,

the unit can be configured to operate as a stand-alone

communicator for interfacing existing third-party control

equipment. Full two-way communication with the TL250 is

achieved using the Sur-Gard System II or the Sur-Gard System III

and its IP line card, the SG-DRL3-IP.

Secure Communication

The TL250 utilizes industry-leading 128-bit AES encryption, polling,

hardware substitution protection, and application-specific

hardware to help eliminate security risks.

Because the TL250 communication stream is minimal and draws

only small amounts of network bandwidth, data transfer remains

timely and accurate.

DLS2002SA Download Software

Simple installation of the TL250 is assured through

utilization of the built-in PC-Link and T-Link Console

software. Administration of accounts can be

accomplished over the Internet from anywhere in the

world using DLS2002SA download software—no other

software application is required.

Software updates can be downloaded remotely from

any personal computer as the hardware platform of the

TL250 features flash upgradeable memory.

Compatibility

The TL250 is compatible with the following control

panels via the built-in PC-Link:

• PC1864 PowerSeries 8-64 zone control panel

• PC1832 PowerSeries 8-32 zone control panel

• PC1616 PowerSeries 6-16 zone control panel

• Power864 PC5020 (version 3.2 or higher)

• MAXSYS PC4020 (version 3.31 or higher)

Direct trigger inputs of the TL250 can be controlled

by outputs on any control panel.

Central station IP receivers:

• Sur-Gard System lll with SG-DRL3-IP line card

• Sur-Gard System ll

Specifications

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . 3.25” x 5.25”

(83 mm x 133 mm)

Input Voltage . . . . . . . . . . . . . . . . . . . . . .12 V DC

Current Draw . . . . . . . . . . . . . . . . . . . . . . 250 mA

(275 mA with PGM or PC5108)

Operating Environment . . . . . . . . . . . . 32° to 120° F

(0° to 49° C)

Relative Humidity . . . . . . . . . . . . . . . . . . 5% to 93%

Ordering Information:

TL250 . . . . . . . . . . . . . . . . . . . . . . . . . . . Internet Alarm Communicator

PC5108 . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Hardwire Zone Expander

DSC T-Link

Internet Alarm Communicator TL250

Specyfikacje produktu

Marka:	DSC
Kategoria:	nieskategoryzowany
Model:	TL250
Typ produktu:	Ethernetowy komunikator alarmowy
Wysokość produktu:	83 mm
Szerokość produktu:	133 mm
Prędkość transferu danych przez Ethernet LAN:	10, 100 Mbit/s
Zakres temperatur (eksploatacja):	0 - 49 °C
Zakres wilgotności względnej:	5 - 93 %
Napięcie:	12 V
Szyfrowanie / bezpieczeństwo:	128-bit AES
Prąd wejściowy:	0.25 A
Rodzaj interfejsu sieci Ethernet:	Fast Ethernet
Obsługiwane produkty:	- PC1864 PowerSeries 8-64 zone control panel\n- PC1832 PowerSeries 8-32 zone control panel\n- PC1616 PowerSeries 6-16 zone control panel\n- Power864 PC5020 (version 3.2 or higher)\n- MAXSYS PC4020 (version 3.31 or higher)